[v5,0/4] Add CMN PLL clock controller driver for IPQ9574

Message

Jie Luo Oct. 28, 2024, 2:04 p.m. UTC

The CMN PLL clock controller in Qualcomm IPQ chipsets provides
the clocks to the networking hardware blocks that are internal
or external to the SoC, and to the GCC. This driver configures
the CMN PLL clock controller to enable the output clocks. The
networking blocks include the internal blocks such as PPE
(Packet Process Engine) and PCS blocks, and external hardware
such as Ethernet PHY or switch. The CMN PLL block also outputs
fixed rate clocks to GCC, such as 24 MHZ as XO clock and 32 KHZ
as sleep clock supplied to GCC.

The controller expects the input reference clock from the internal
Wi-Fi block acting as the clock source. The output clocks supplied
by the controller are fixed rate clocks.

The CMN PLL hardware block does not include any other function
other than enabling the clocks to the networking hardware blocks
and GCC.

The driver is being enabled to support IPQ9574 SoC initially, and
will be extended for other SoCs.

Signed-off-by: Luo Jie <[e-mail]>
---
Changes in v5:
- Move the hardware configurations into set_rate() from determine_rate().
- Remove the dependency on IPQ_GCC_9574.
- Correct the header files included.
- Update reference clock of CMN PLL to use fixed factor clock.
- Link to v4: https://lore.kernel.org/r/[e-mail]

Changes in v4:
- Rename driver file to ipq-cmn-pll.c
- Register CMN PLL as a 12 GHZ clock.
- Configure CMN PLL input ref clock using clk_ops::determine_rate().
  Add the additional output clocks to GCC and PCS.
- Update the same information in dtbindings.
- Use PM clock APIs for input clock enablement.
- Link to v3: https://lore.kernel.org/r/[e-mail]

Changes in v3:
- Update description of dt-binding to explain scope of 'CMN' in CMN PLL.
- Collect Reviewed-by tags for dtbindings and defconfig patches.
- Enable PLL_LOCKED check for the stability of output clocks.
- Link to v2: https://lore.kernel.org/r/[e-mail]

Changes in v2:
- Rename the dt-binding file with the compatible.
- Remove property 'clock-output-names' from dt-bindings and define
  names in the driver. Add qcom,ipq-cmn-pll.h to export the output
  clock specifier.
- Alphanumeric ordering of 'cmn_pll_ref_clk' node in DTS.
- Fix allmodconfig error reported by test robot.
- Replace usage of "common" to "CMN" to match the name with the
  hardware specification.
- Clarify in commit message on scope of CMN PLL function.
- Link to v1: https://lore.kernel.org/r/[e-mail]

---
Luo Jie (4):
      dt-bindings: clock: qcom: Add CMN PLL clock controller for IPQ SoC
      clk: qcom: Add CMN PLL clock controller driver for IPQ SoC
      arm64: defconfig: Enable Qualcomm IPQ CMN PLL clock controller
      arm64: dts: qcom: Add CMN PLL node for IPQ9574 SoC

 .../bindings/clock/qcom,ipq9574-cmn-pll.yaml       |  85 ++++
 arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi   |  16 +-
 arch/arm64/boot/dts/qcom/ipq9574.dtsi              |  26 +-
 arch/arm64/configs/defconfig                       |   1 +
 drivers/clk/qcom/Kconfig                           |   9 +
 drivers/clk/qcom/Makefile                          |   1 +
 drivers/clk/qcom/ipq-cmn-pll.c                     | 436 +++++++++++++++++++++
 include/dt-bindings/clock/qcom,ipq-cmn-pll.h       |  22 ++
 8 files changed, 594 insertions(+), 2 deletions(-)
---
base-commit: d61a00525464bfc5fe92c6ad713350988e492b88
change-id: 20241014-qcom_ipq_cmnpll-bde0638f4116

Best regards,