@@ -316,6 +316,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8064-ifc6410.dtb \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq8064-ap148.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb
dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
new file mode 100644
@@ -0,0 +1,85 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+/ {
+ model = "Qualcomm IPQ8064/AP148";
+ compatible = "qcom,ipq8064-ap148", "qcom,ipq8064";
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ soc {
+ pinmux@800000 {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+
+ i2c4: i2c@16380000 {
+ status = "ok";
+
+ clock-frequency = <200000>;
+
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "default";
+ };
+ };
+
+ gsbi5: gsbi@1a200000 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "ok";
+
+ spi4: spi@1a280000 {
+ status = "ok";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 0>;
+
+ flash: m25p80@0 {
+ compatible = "s25fl256s1";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partition@0 {
+ label = "rootfs";
+ reg = <0x0 0x1000000>;
+ };
+
+ partition@1 {
+ label = "scratch";
+ reg = <0x1000000 0x1000000>;
+ };
+ };
+ };
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1 @@
+#include "qcom-ipq8064.dtsi"
new file mode 100644
@@ -0,0 +1,250 @@
+/dts-v1/;
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+
+/ {
+ model = "Qualcomm IPQ8064";
+ compatible = "qcom,ipq8064";
+ interrupt-parent = <&intc>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "qcom,krait";
+ enable-method = "qcom,kpss-acc-v1";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
+ };
+
+ cpu@1 {
+ compatible = "qcom,krait";
+ enable-method = "qcom,kpss-acc-v1";
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
+ };
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ cpu-pmu {
+ compatible = "qcom,krait-pmu";
+ interrupts = <1 10 0x304>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ nss@40000000 {
+ reg = <0x40000000 0x1000000>;
+ no-map;
+ };
+
+ smem@41000000 {
+ reg = <0x41000000 0x200000>;
+ no-map;
+ };
+ };
+
+ soc: soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "simple-bus";
+
+ qcom_pinmux: pinmux@800000 {
+ compatible = "qcom,ipq8064-pinctrl";
+ reg = <0x800000 0x4000>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <0 32 0x4>;
+ };
+
+ intc: interrupt-controller@2000000 {
+ compatible = "qcom,msm-qgic2";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x02000000 0x1000>,
+ <0x02002000 0x1000>;
+ };
+
+ timer@200a000 {
+ compatible = "qcom,kpss-timer", "qcom,msm-timer";
+ interrupts = <1 1 0x301>,
+ <1 2 0x301>,
+ <1 3 0x301>;
+ reg = <0x0200a000 0x100>;
+ clock-frequency = <25000000>,
+ <32768>;
+ cpu-offset = <0x80000>;
+ };
+
+ acc0: clock-controller@2088000 {
+ compatible = "qcom,kpss-acc-v1";
+ reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+ };
+
+ acc1: clock-controller@2098000 {
+ compatible = "qcom,kpss-acc-v1";
+ reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+ };
+
+ saw0: regulator@2089000 {
+ compatible = "qcom,saw2";
+ reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+ regulator;
+ };
+
+ saw1: regulator@2099000 {
+ compatible = "qcom,saw2";
+ reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+ regulator;
+ };
+
+ gsbi2: gsbi@12480000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ reg = <0x12480000 0x100>;
+ clocks = <&gcc GSBI2_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ serial@12490000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x12490000 0x1000>,
+ <0x12480000 0x1000>;
+ interrupts = <0 195 0x0>;
+ clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ i2c@124a0000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x124a0000 0x1000>;
+ interrupts = <0 196 0>;
+
+ clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ };
+
+ gsbi4: gsbi@16300000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ reg = <0x16300000 0x100>;
+ clocks = <&gcc GSBI4_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ serial@16340000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x16340000 0x1000>,
+ <0x16300000 0x1000>;
+ interrupts = <0 152 0x0>;
+ clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ i2c@16380000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x16380000 0x1000>;
+ interrupts = <0 153 0>;
+
+ clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ gsbi5: gsbi@1a200000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ reg = <0x1a200000 0x100>;
+ clocks = <&gcc GSBI5_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ serial@1a240000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x1a240000 0x1000>,
+ <0x1a200000 0x1000>;
+ interrupts = <0 154 0x0>;
+ clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ i2c@1a280000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x1a280000 0x1000>;
+ interrupts = <0 155 0>;
+
+ clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi@1a280000 {
+ compatible = "qcom,spi-qup-v1.1.1";
+ reg = <0x1a280000 0x1000>;
+ interrupts = <0 155 0>;
+
+ clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ qcom,ssbi@500000 {
+ compatible = "qcom,ssbi";
+ reg = <0x00500000 0x1000>;
+ qcom,controller-type = "pmic-arbiter";
+ };
+
+ gcc: clock-controller@900000 {
+ compatible = "qcom,gcc-ipq8064";
+ reg = <0x00900000 0x4000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+ };
+};
@@ -18,6 +18,8 @@ static const char * const qcom_dt_match[] __initconst = {
"qcom,apq8064",
"qcom,apq8074-dragonboard",
"qcom,apq8084",
+ "qcom,ipq8062",
+ "qcom,ipq8064",
"qcom,msm8660-surf",
"qcom,msm8960-cdp",
NULL
Add basic IPQ8064 SoC include device tree and support for basic booting on the AP148 Reference board with support for UART, I2C, and SPI. Signed-off-by: Kumar Gala <galak@codeaurora.org> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 85 +++++++++++ arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi | 1 + arch/arm/boot/dts/qcom-ipq8064.dtsi | 250 +++++++++++++++++++++++++++++++ arch/arm/mach-qcom/board.c | 2 + 5 files changed, 339 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq8064-ap148.dts create mode 100644 arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi create mode 100644 arch/arm/boot/dts/qcom-ipq8064.dtsi