| Message ID | 1407845127-8448-1-git-send-email-srinivas.kandadgatla@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Aug 12, 2014 at 2:05 PM, Srinivas Kandagatla <srinivas.kandagatla@linaro.org> wrote: > From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > This patch moves ST specific sdio setup under a vendor id condition, > this will ensure that the ST specfic setup is not done on other vendor > like Qualcomm. > > Originally the issue was detected while testing WLAN ath6kl on IFC6410 > board with APQ8064 SOC. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> So instead of again checking hw_designer (I think that's a bit messy) and instead of having the flag bool sdio from patch 1, why not introduce 2 flags in vendor_data: bool st_sdio; bool qcom_sdio; > +++ b/drivers/mmc/host/mmci.c > @@ -828,7 +828,8 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data) > * otherwise the transfer will not start. The threshold > * depends on the rate of MCLK. > */ > - if (data->flags & MMC_DATA_WRITE && > + if (host->hw_designer == AMBA_VENDOR_ST && > + data->flags & MMC_DATA_WRITE && And this becomes just if (variant->st_sdio)... > (host->size < 8 || > (host->size <= 8 && host->mclk > 50000000))) > clk = host->clk_reg & ~variant->clkreg_enable; Yours, Linus Walleij -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Thankyou Linus for the feedback. On 13/08/14 09:58, Linus Walleij wrote: > On Tue, Aug 12, 2014 at 2:05 PM, Srinivas Kandagatla > <srinivas.kandagatla@linaro.org> wrote: > >> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >> >> This patch moves ST specific sdio setup under a vendor id condition, >> this will ensure that the ST specfic setup is not done on other vendor >> like Qualcomm. >> >> Originally the issue was detected while testing WLAN ath6kl on IFC6410 >> board with APQ8064 SOC. >> >> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > So instead of again checking hw_designer (I think that's a bit > messy) and instead of having the flag bool sdio from patch > 1, why not introduce 2 flags in vendor_data: > > bool st_sdio; > bool qcom_sdio; Thats good idea, If we rename the existing sdio flag to st_sdio, then we can get rid of the first patch too. As there is no specific sdio logic required for qcom. I will send the change in next version. thanks srini > >> +++ b/drivers/mmc/host/mmci.c >> @@ -828,7 +828,8 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data) >> * otherwise the transfer will not start. The threshold >> * depends on the rate of MCLK. >> */ >> - if (data->flags & MMC_DATA_WRITE && >> + if (host->hw_designer == AMBA_VENDOR_ST && >> + data->flags & MMC_DATA_WRITE && > > And this becomes just > > if (variant->st_sdio)... > >> (host->size < 8 || >> (host->size <= 8 && host->mclk > 50000000))) >> clk = host->clk_reg & ~variant->clkreg_enable; > > Yours, > Linus Walleij > -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index 848e2bb..1783be7 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -828,7 +828,8 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data) * otherwise the transfer will not start. The threshold * depends on the rate of MCLK. */ - if (data->flags & MMC_DATA_WRITE && + if (host->hw_designer == AMBA_VENDOR_ST && + data->flags & MMC_DATA_WRITE && (host->size < 8 || (host->size <= 8 && host->mclk > 50000000))) clk = host->clk_reg & ~variant->clkreg_enable;