| Message ID | 1429796773-7151-6-git-send-email-rnayak@codeaurora.org (mailing list archive) |
|---|---|
| State | RFC |
| Headers | show |
On Thu, Apr 23 2015 at 07:52 -0600, Rajendra Nayak wrote: >Add thermal zones, tsens and eeprom nodes I dont see corresponding patches for 8084 and 8916. -- Lina > >Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> >--- > arch/arm/boot/dts/qcom-msm8974.dtsi | 105 ++++++++++++++++++++++++++++++++++++ > 1 file changed, 105 insertions(+) > >diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi >index e265ec1..5716e89 100644 >--- a/arch/arm/boot/dts/qcom-msm8974.dtsi >+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi >@@ -57,6 +57,88 @@ > }; > }; > >+ thermal-zones { >+ cpu-thermal0 { >+ polling-delay-passive = <250>; >+ polling-delay = <1000>; >+ >+ thermal-sensors = <&tsens 5>; >+ >+ trips { >+ cpu_alert0: trip@0 { >+ temperature = <100000>; >+ hysteresis = <2000>; >+ type = "passive"; >+ }; >+ cpu_crit0: trip@1 { >+ temperature = <125000>; >+ hysteresis = <2000>; >+ type = "critical"; >+ }; >+ }; >+ }; >+ >+ cpu-thermal1 { >+ polling-delay-passive = <250>; >+ polling-delay = <1000>; >+ >+ thermal-sensors = <&tsens 6>; >+ >+ trips { >+ cpu_alert1: trip@0 { >+ temperature = <100000>; >+ hysteresis = <2000>; >+ type = "passive"; >+ }; >+ cpu_crit1: trip@1 { >+ temperature = <125000>; >+ hysteresis = <2000>; >+ type = "critical"; >+ }; >+ }; >+ }; >+ >+ cpu-thermal2 { >+ polling-delay-passive = <250>; >+ polling-delay = <1000>; >+ >+ thermal-sensors = <&tsens 7>; >+ >+ trips { >+ cpu_alert2: trip@0 { >+ temperature = <100000>; >+ hysteresis = <2000>; >+ type = "passive"; >+ }; >+ cpu_crit2: trip@1 { >+ temperature = <125000>; >+ hysteresis = <2000>; >+ type = "critical"; >+ }; >+ }; >+ }; >+ >+ cpu-thermal3 { >+ polling-delay-passive = <250>; >+ polling-delay = <1000>; >+ >+ thermal-sensors = <&tsens 8>; >+ >+ trips { >+ cpu_alert3: trip@0 { >+ temperature = <100000>; >+ hysteresis = <2000>; >+ type = "passive"; >+ }; >+ cpu_crit3: trip@1 { >+ temperature = <125000>; >+ hysteresis = <2000>; >+ type = "critical"; >+ }; >+ }; >+ }; >+ }; >+ > cpu-pmu { > compatible = "qcom,krait-pmu"; > interrupts = <1 7 0xf04>; >@@ -85,6 +167,29 @@ > <0xf9002000 0x1000>; > }; > >+ qfprom: qfprom@fc4bc000 { >+ #address-cells = <1>; >+ #size-cells = <1>; >+ compatible = "qcom,qfprom"; >+ reg = <0xfc4bc000 0x1000>; >+ tsens_calib: calib@d0 { >+ reg = <0xd0 0x18>; >+ }; >+ tsens_backup: backup@440 { >+ reg = <0x440 0x10>; >+ }; >+ }; >+ >+ tsens: thermal-sensor@fc4a8000 { >+ compatible = "qcom,msm8974-tsens"; >+ reg = <0xfc4a8000 0x2000>; >+ calib = <&tsens_calib>; >+ calib_backup = <&tsens_backup>; >+ qcom,tsens-slopes = <3200 3200 3200 3200 3200 3200 >+ 3200 3200 3200 3200 3200>; >+ #thermal-sensor-cells = <1>; >+ }; >+ > timer@f9020000 { > #address-cells = <1>; > #size-cells = <1>; >-- >QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member >of Code Aurora Forum, hosted by The Linux Foundation > -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 04/23/2015 10:21 PM, Lina Iyer wrote: > On Thu, Apr 23 2015 at 07:52 -0600, Rajendra Nayak wrote: >> Add thermal zones, tsens and eeprom nodes > > I dont see corresponding patches for 8084 and 8916. I did not add 8916 as the dts for it isn't upstream (yet), and I hadn't tested on 8084 but I can certainly do so and update the dts files when I do a respin. > > -- Lina >> >> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> >> --- >> arch/arm/boot/dts/qcom-msm8974.dtsi | 105 >> ++++++++++++++++++++++++++++++++++++ >> 1 file changed, 105 insertions(+) >> >> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi >> b/arch/arm/boot/dts/qcom-msm8974.dtsi >> index e265ec1..5716e89 100644 >> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi >> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi >> @@ -57,6 +57,88 @@ >> }; >> }; >> >> + thermal-zones { >> + cpu-thermal0 { >> + polling-delay-passive = <250>; >> + polling-delay = <1000>; >> + >> + thermal-sensors = <&tsens 5>; >> + >> + trips { >> + cpu_alert0: trip@0 { >> + temperature = <100000>; >> + hysteresis = <2000>; >> + type = "passive"; >> + }; >> + cpu_crit0: trip@1 { >> + temperature = <125000>; >> + hysteresis = <2000>; >> + type = "critical"; >> + }; >> + }; >> + }; >> + >> + cpu-thermal1 { >> + polling-delay-passive = <250>; >> + polling-delay = <1000>; >> + >> + thermal-sensors = <&tsens 6>; >> + >> + trips { >> + cpu_alert1: trip@0 { >> + temperature = <100000>; >> + hysteresis = <2000>; >> + type = "passive"; >> + }; >> + cpu_crit1: trip@1 { >> + temperature = <125000>; >> + hysteresis = <2000>; >> + type = "critical"; >> + }; >> + }; >> + }; >> + >> + cpu-thermal2 { >> + polling-delay-passive = <250>; >> + polling-delay = <1000>; >> + >> + thermal-sensors = <&tsens 7>; >> + >> + trips { >> + cpu_alert2: trip@0 { >> + temperature = <100000>; >> + hysteresis = <2000>; >> + type = "passive"; >> + }; >> + cpu_crit2: trip@1 { >> + temperature = <125000>; >> + hysteresis = <2000>; >> + type = "critical"; >> + }; >> + }; >> + }; >> + >> + cpu-thermal3 { >> + polling-delay-passive = <250>; >> + polling-delay = <1000>; >> + >> + thermal-sensors = <&tsens 8>; >> + >> + trips { >> + cpu_alert3: trip@0 { >> + temperature = <100000>; >> + hysteresis = <2000>; >> + type = "passive"; >> + }; >> + cpu_crit3: trip@1 { >> + temperature = <125000>; >> + hysteresis = <2000>; >> + type = "critical"; >> + }; >> + }; >> + }; >> + }; >> + >> cpu-pmu { >> compatible = "qcom,krait-pmu"; >> interrupts = <1 7 0xf04>; >> @@ -85,6 +167,29 @@ >> <0xf9002000 0x1000>; >> }; >> >> + qfprom: qfprom@fc4bc000 { >> + #address-cells = <1>; >> + #size-cells = <1>; >> + compatible = "qcom,qfprom"; >> + reg = <0xfc4bc000 0x1000>; >> + tsens_calib: calib@d0 { >> + reg = <0xd0 0x18>; >> + }; >> + tsens_backup: backup@440 { >> + reg = <0x440 0x10>; >> + }; >> + }; >> + >> + tsens: thermal-sensor@fc4a8000 { >> + compatible = "qcom,msm8974-tsens"; >> + reg = <0xfc4a8000 0x2000>; >> + calib = <&tsens_calib>; >> + calib_backup = <&tsens_backup>; >> + qcom,tsens-slopes = <3200 3200 3200 3200 3200 3200 >> + 3200 3200 3200 3200 3200>; >> + #thermal-sensor-cells = <1>; >> + }; >> + >> timer@f9020000 { >> #address-cells = <1>; >> #size-cells = <1>; >> -- >> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member >> of Code Aurora Forum, hosted by The Linux Foundation >>
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index e265ec1..5716e89 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -57,6 +57,88 @@ }; }; + thermal-zones { + cpu-thermal0 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 5>; + + trips { + cpu_alert0: trip@0 { + temperature = <100000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit0: trip@1 { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu-thermal1 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 6>; + + trips { + cpu_alert1: trip@0 { + temperature = <100000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit1: trip@1 { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu-thermal2 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 7>; + + trips { + cpu_alert2: trip@0 { + temperature = <100000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit2: trip@1 { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu-thermal3 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 8>; + + trips { + cpu_alert3: trip@0 { + temperature = <100000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit3: trip@1 { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; + cpu-pmu { compatible = "qcom,krait-pmu"; interrupts = <1 7 0xf04>; @@ -85,6 +167,29 @@ <0xf9002000 0x1000>; }; + qfprom: qfprom@fc4bc000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "qcom,qfprom"; + reg = <0xfc4bc000 0x1000>; + tsens_calib: calib@d0 { + reg = <0xd0 0x18>; + }; + tsens_backup: backup@440 { + reg = <0x440 0x10>; + }; + }; + + tsens: thermal-sensor@fc4a8000 { + compatible = "qcom,msm8974-tsens"; + reg = <0xfc4a8000 0x2000>; + calib = <&tsens_calib>; + calib_backup = <&tsens_backup>; + qcom,tsens-slopes = <3200 3200 3200 3200 3200 3200 + 3200 3200 3200 3200 3200>; + #thermal-sensor-cells = <1>; + }; + timer@f9020000 { #address-cells = <1>; #size-cells = <1>;
Add thermal zones, tsens and eeprom nodes Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> --- arch/arm/boot/dts/qcom-msm8974.dtsi | 105 ++++++++++++++++++++++++++++++++++++ 1 file changed, 105 insertions(+)