diff mbox

[v3,2/2] drm/msm/hdmi: Use pinctrl in HDMI driver

Message ID 1433453502-18092-3-git-send-email-sviau@codeaurora.org (mailing list archive)
State Not Applicable, archived
Delegated to: Andy Gross
Headers show

Commit Message

Stephane Viau June 4, 2015, 9:31 p.m. UTC 
Some targets (eg: msm8994) use the pinctrl framework to configure
interface pins. This change adds support for initialization and
pinctrl active/sleep state control for the HDMI driver.

Signed-off-by: Stephane Viau <sviau@codeaurora.org>
---
v3:
- Use pins binding handled in driver really_probe()          [Ivan]

v2:
- Add devicetree binding documentation for pinctrl property  [Ivan]
- Use pinctrl framework's PINCTRL_STATE_DEFAULT/SLEEP states [Ivan]

 Documentation/devicetree/bindings/drm/msm/hdmi.txt |  6 ++++++
 drivers/gpu/drm/msm/hdmi/hdmi_connector.c          | 11 +++++++++++
 2 files changed, 17 insertions(+)
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/drm/msm/hdmi.txt b/Documentation/devicetree/bindings/drm/msm/hdmi.txt
index a29a55f..c43aa53 100644
--- a/Documentation/devicetree/bindings/drm/msm/hdmi.txt
+++ b/Documentation/devicetree/bindings/drm/msm/hdmi.txt
@@ -20,6 +20,9 @@  Required properties:
 Optional properties:
 - qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
 - qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin
+- pinctrl-names: the pin control state names; should contain "default"
+- pinctrl-0: the default pinctrl state (active)
+- pinctrl-1: the "sleep" pinctrl state
 
 Example:
 
@@ -44,5 +47,8 @@  Example:
 		qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>;
 		core-vdda-supply = <&pm8921_hdmi_mvs>;
 		hdmi-mux-supply = <&ext_3p3v>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&hpd_active  &ddc_active  &cec_active>;
+		pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>;
 	};
 };
diff --git a/drivers/gpu/drm/msm/hdmi/hdmi_connector.c b/drivers/gpu/drm/msm/hdmi/hdmi_connector.c
index e29b62a..ece572d 100644
--- a/drivers/gpu/drm/msm/hdmi/hdmi_connector.c
+++ b/drivers/gpu/drm/msm/hdmi/hdmi_connector.c
@@ -16,6 +16,7 @@ 
  */
 
 #include <linux/gpio.h>
+#include <linux/pinctrl/consumer.h>
 
 #include "msm_kms.h"
 #include "hdmi.h"
@@ -199,6 +200,12 @@  static int hpd_enable(struct hdmi_connector *hdmi_connector)
 		}
 	}
 
+	ret = pinctrl_pm_select_default_state(dev);
+	if (ret) {
+		dev_err(dev, "pinctrl state chg failed: %d\n", ret);
+		goto fail;
+	}
+
 	ret = gpio_config(hdmi, true);
 	if (ret) {
 		dev_err(dev, "failed to configure GPIOs: %d\n", ret);
@@ -268,6 +275,10 @@  static void hdp_disable(struct hdmi_connector *hdmi_connector)
 	if (ret)
 		dev_warn(dev, "failed to unconfigure GPIOs: %d\n", ret);
 
+	ret = pinctrl_pm_select_sleep_state(dev);
+	if (ret)
+		dev_warn(dev, "pinctrl state chg failed: %d\n", ret);
+
 	for (i = 0; i < config->hpd_reg_cnt; i++) {
 		ret = regulator_disable(hdmi->hpd_regs[i]);
 		if (ret)