@@ -11,6 +11,7 @@ on the Qualcomm Hexagon core.
"qcom,msm8916-mss-pil",
"qcom,msm8974-mss-pil"
+ "qcom,msm8996-mss-pil"
- reg:
Usage: required
Value type: <prop-encoded-array>
@@ -32,6 +32,7 @@
#include <linux/soc/qcom/mdt_loader.h>
#include <linux/soc/qcom/smem.h>
#include <linux/soc/qcom/smem_state.h>
+#include <linux/iopoll.h>
#include "remoteproc_internal.h"
#include "qcom_common.h"
@@ -64,6 +65,8 @@
#define QDSP6SS_RESET_REG 0x014
#define QDSP6SS_GFMUX_CTL_REG 0x020
#define QDSP6SS_PWR_CTL_REG 0x030
+#define QDSP6SS_MEM_PWR_CTL 0x0B0
+#define QDSP6SS_STRAP_ACC 0x110
/* AXI Halt Register Offsets */
#define AXI_HALTREQ_REG 0x0
@@ -92,6 +95,15 @@
#define QDSS_BHS_ON BIT(21)
#define QDSS_LDO_BYP BIT(22)
+/* QDSP6v56 parameters */
+#define QDSP6v56_LDO_BYP BIT(25)
+#define QDSP6v56_BHS_ON BIT(24)
+#define QDSP6v56_CLAMP_WL BIT(21)
+#define QDSP6v56_CLAMP_QMC_MEM BIT(22)
+#define HALT_CHECK_MAX_LOOPS 200
+#define QDSP6SS_XO_CBCR 0x0038
+#define QDSP6SS_ACC_OVERRIDE_VAL 0x20
+
struct reg_info {
struct regulator *reg;
int uV;
@@ -110,6 +122,7 @@ struct rproc_hexagon_res {
struct qcom_mss_reg_res *active_supply;
char **proxy_clk_names;
char **active_clk_names;
+ int version;
bool need_mem_protection;
};
@@ -157,6 +170,13 @@ struct q6v5 {
struct qcom_rproc_subdev smd_subdev;
int mpss_perm;
int mba_perm;
+ int version;
+};
+
+enum {
+ MSS_MSM8916,
+ MSS_MSM8974,
+ MSS_MSM8996,
};
static int q6v5_regulator_init(struct device *dev, struct reg_info *regs,
@@ -386,33 +406,97 @@ static int q6v5proc_reset(struct q6v5 *qproc)
{
u32 val;
int ret;
+ int i;
- /* Assert resets, stop core */
- val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
- val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE);
- writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
- /* Enable power block headswitch, and wait for it to stabilize */
- val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val |= QDSS_BHS_ON | QDSS_LDO_BYP;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- udelay(1);
-
- /*
- * Turn on memories. L2 banks should be done individually
- * to minimize inrush current.
- */
- val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val |= Q6SS_SLP_RET_N | Q6SS_L2TAG_SLP_NRET_N |
- Q6SS_ETB_SLP_NRET_N | Q6SS_L2DATA_STBY_N;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val |= Q6SS_L2DATA_SLP_NRET_N_2;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val |= Q6SS_L2DATA_SLP_NRET_N_1;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val |= Q6SS_L2DATA_SLP_NRET_N_0;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ if (qproc->version == MSS_MSM8996) {
+ /* Override the ACC value if required */
+ writel(QDSP6SS_ACC_OVERRIDE_VAL,
+ qproc->reg_base + QDSP6SS_STRAP_ACC);
+
+ /* Assert resets, stop core */
+ val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
+ val |= Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE;
+ writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
+
+ /* BHS require xo cbcr to be enabled */
+ val = readl(qproc->reg_base + QDSP6SS_XO_CBCR);
+ val |= 0x1;
+ writel(val, qproc->reg_base + QDSP6SS_XO_CBCR);
+ /* Read CLKOFF bit to go low indicating CLK is enabled */
+ ret = readl_poll_timeout(qproc->reg_base + QDSP6SS_XO_CBCR,
+ val, !(val & BIT(31)), 1, HALT_CHECK_MAX_LOOPS);
+ if (ret) {
+ dev_err(qproc->dev,
+ "xo cbcr enabling timed out (rc:%d)\n", ret);
+ return ret;
+ }
+ /* Enable power block headswitch and wait for it to stabilize */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= QDSP6v56_BHS_ON;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ udelay(1);
+
+ /* Put LDO in bypass mode */
+ val |= QDSP6v56_LDO_BYP;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* Deassert QDSP6 compiler memory clamp */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val &= ~QDSP6v56_CLAMP_QMC_MEM;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* Deassert memory peripheral sleep and L2 memory standby */
+ val |= Q6SS_L2DATA_STBY_N | Q6SS_SLP_RET_N;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* Turn on L1, L2, ETB and JU memories 1 at a time */
+ val = readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
+ for (i = 19; i >= 0; i--) {
+ val |= BIT(i);
+ writel(val, qproc->reg_base +
+ QDSP6SS_MEM_PWR_CTL);
+ /*
+ * Read back value to ensure the write is done then
+ * wait for 1us for both memory peripheral and data
+ * array to turn on.
+ */
+ val |= readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
+ udelay(1);
+ }
+ /* Remove word line clamp */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val &= ~QDSP6v56_CLAMP_WL;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ } else {
+ /* Assert resets, stop core */
+ val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
+ val |= Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE;
+ writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
+
+ /* Enable power block headswitch and wait for it to stabilize */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= QDSS_BHS_ON | QDSS_LDO_BYP;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ udelay(1);
+ /*
+ * Turn on memories. L2 banks should be done individually
+ * to minimize inrush current.
+ */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= Q6SS_SLP_RET_N | Q6SS_L2TAG_SLP_NRET_N |
+ Q6SS_ETB_SLP_NRET_N | Q6SS_L2DATA_STBY_N;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= Q6SS_L2DATA_SLP_NRET_N_2;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= Q6SS_L2DATA_SLP_NRET_N_1;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= Q6SS_L2DATA_SLP_NRET_N_0;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ }
/* Remove IO clamp */
val &= ~Q6SS_CLAMP_IO;
writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
@@ -788,6 +872,15 @@ static int q6v5_stop(struct rproc *rproc)
q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem);
q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc);
+ if (qproc->version == MSS_MSM8996) {
+ /*
+ * To avoid high MX current during LPASS/MSS restart.
+ */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= Q6SS_CLAMP_IO | QDSP6v56_CLAMP_WL |
+ QDSP6v56_CLAMP_QMC_MEM;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ }
ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, 0,
qproc->mpss_phys, qproc->mpss_size);
WARN_ON(ret);
@@ -1088,6 +1181,7 @@ static int q6v5_probe(struct platform_device *pdev)
if (ret)
goto free_rproc;
+ qproc->version = desc->version;
qproc->need_mem_protection = desc->need_mem_protection;
ret = q6v5_request_irq(qproc, pdev, "wdog", q6v5_wdog_interrupt);
if (ret < 0)
@@ -1138,6 +1232,24 @@ static int q6v5_remove(struct platform_device *pdev)
return 0;
}
+static const struct rproc_hexagon_res msm8996_mss = {
+ .hexagon_mba_image = "mba.mbn",
+ .proxy_clk_names = (char*[]){
+ "xo",
+ "pnoc",
+ NULL
+ },
+ .active_clk_names = (char*[]){
+ "iface",
+ "bus",
+ "mem",
+ "gpll0_mss_clk",
+ NULL
+ },
+ .need_mem_protection = true,
+ .version = MSS_MSM8996,
+};
+
static const struct rproc_hexagon_res msm8916_mss = {
.hexagon_mba_image = "mba.mbn",
.proxy_supply = (struct qcom_mss_reg_res[]) {
@@ -1166,6 +1278,7 @@ static int q6v5_remove(struct platform_device *pdev)
NULL
},
.need_mem_protection = false,
+ .version = MSS_MSM8916,
};
static const struct rproc_hexagon_res msm8974_mss = {
@@ -1204,12 +1317,14 @@ static int q6v5_remove(struct platform_device *pdev)
NULL
},
.need_mem_protection = false,
+ .version = MSS_MSM8974,
};
static const struct of_device_id q6v5_of_match[] = {
{ .compatible = "qcom,q6v5-pil", .data = &msm8916_mss},
{ .compatible = "qcom,msm8916-mss-pil", .data = &msm8916_mss},
{ .compatible = "qcom,msm8974-mss-pil", .data = &msm8974_mss},
+ { .compatible = "qcom,msm8996-mss-pil", .data = &msm8996_mss},
{ },
};
MODULE_DEVICE_TABLE(of, q6v5_of_match);
This patch add support for mss boot on msm8996. Major changes include initializing mss rproc for msm8996, making appropriate change for executing mss reset sequence etc. Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org> --- .../devicetree/bindings/remoteproc/qcom,q6v5.txt | 1 + drivers/remoteproc/qcom_q6v5_pil.c | 163 ++++++++++++++++++--- 2 files changed, 140 insertions(+), 24 deletions(-)