[v3,13/16] phy: qcom-qmp: Add support for QMP V3 USB3 PHY

Commit Message

Manu Gautam Nov. 21, 2017, 9:23 a.m. UTC

QMP V3 USB3 PHY is a DisplayPort (DP) and USB combo PHY
with dual RX/TX lanes to support type-c. There is a
separate block DP_COM for configuration related to type-c
or DP. Add support for dp_com region and secondary rx/tx
lanes initialization.

Signed-off-by: Manu Gautam <[e-mail]>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 223 +++++++++++++++++++++++++++++++++++-
 1 file changed, 220 insertions(+), 3 deletions(-)

Patch

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 15a734f..efd187b 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -47,6 +47,21 @@ 
 /* QPHY_COM_PCS_READY_STATUS bit */
 #define PCS_READY				BIT(0)
 
+/* QPHY_V3_DP_COM_RESET_OVRD_CTRL register bits */
+/* DP PHY soft reset */
+#define SW_DPPHY_RESET				BIT(0)
+/* mux to select DP PHY reset control, 0:HW control, 1: software reset */
+#define SW_DPPHY_RESET_MUX			BIT(1)
+/* USB3 PHY soft reset */
+#define SW_USB3PHY_RESET			BIT(2)
+/* mux to select USB3 PHY reset control, 0:HW control, 1: software reset */
+#define SW_USB3PHY_RESET_MUX			BIT(3)
+
+/* QPHY_V3_DP_COM_PHY_MODE_CTRL register bits */
+#define USB3_MODE				BIT(0) /* enables USB3 mode */
+#define DP_MODE					BIT(1) /* enables DP mode */
+
+
 #define PHY_INIT_COMPLETE_TIMEOUT		1000
 #define POWER_DOWN_DELAY_US_MIN			10
 #define POWER_DOWN_DELAY_US_MAX			11
@@ -122,6 +137,12 @@  enum qphy_reg_layout {
 	[QPHY_PCS_READY_STATUS]		= 0x17c,
 };
 
+static const unsigned int qmp_v3_usb3phy_regs_layout[] = {
+	[QPHY_SW_RESET]			= 0x00,
+	[QPHY_START_CTRL]		= 0x08,
+	[QPHY_PCS_READY_STATUS]		= 0x174,
+};
+
 static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = {
 	QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c),
 	QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
@@ -350,6 +371,112 @@  enum qphy_reg_layout {
 	QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3),
 };
 
+static const struct qmp_phy_init_tbl qmp_v3_usb3_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x09),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_pcs_tbl[] = {
+	/* FLL settings */
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
+
+	/* Lock Det settings */
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
+
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xba),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb7),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4e),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x65),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6b),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
+
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
+};
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -394,6 +521,12 @@  struct qmp_phy_cfg {
 	/* power_down delay in usec */
 	int pwrdn_delay_min;
 	int pwrdn_delay_max;
+
+	/* true, if PHY has a separate DP_COM control block */
+	bool has_phy_dp_com_ctrl;
+	/* Register offset of secondary tx/rx lanes for USB DP combo PHY */
+	unsigned int tx_b_lane_offset;
+	unsigned int rx_b_lane_offset;
 };
 
 /**
@@ -424,6 +557,7 @@  struct qmp_phy {
  *
  * @dev: device
  * @serdes: iomapped memory space for phy's serdes
+ * @dp_com: iomapped memory space for phy's dp_com control block
  *
  * @clks: array of clocks required by phy
  * @resets: array of resets required by phy
@@ -437,6 +571,7 @@  struct qmp_phy {
 struct qcom_qmp {
 	struct device *dev;
 	void __iomem *serdes;
+	void __iomem *dp_com;
 
 	struct clk_bulk_data *clks;
 	struct reset_control **resets;
@@ -478,6 +613,10 @@  static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 	"aux", "cfg_ahb", "ref",
 };
 
+static const char * const qmp_v3_phy_clk_l[] = {
+	"aux", "cfg_ahb", "ref", "com_aux",
+};
+
 /* list of resets */
 static const char * const msm8996_pciephy_reset_l[] = {
 	"phy", "common", "cfg",
@@ -584,6 +723,38 @@  static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 	.pwrdn_delay_max	= 1005,		/* us */
 };
 
+static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= qmp_v3_usb3_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
+	.tx_tbl			= qmp_v3_usb3_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_tx_tbl),
+	.rx_tbl			= qmp_v3_usb3_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_rx_tbl),
+	.pcs_tbl		= qmp_v3_usb3_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_pcs_tbl),
+	.clk_list		= qmp_v3_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v3_phy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= msm8996_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(msm8996_phy_vreg_l),
+	.regs			= qmp_v3_usb3phy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+	.mask_pcs_ready		= PHYSTATUS,
+
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+
+	.has_phy_dp_com_ctrl	= true,
+	.tx_b_lane_offset	= 0x400,
+	.rx_b_lane_offset	= 0x400,
+};
+
 static void qcom_qmp_phy_configure(void __iomem *base,
 				   const unsigned int *regs,
 				   const struct qmp_phy_init_tbl tbl[],
@@ -607,6 +778,7 @@  static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
 {
 	const struct qmp_phy_cfg *cfg = qmp->cfg;
 	void __iomem *serdes = qmp->serdes;
+	void __iomem *dp_com = qmp->dp_com;
 	int ret, i;
 
 	mutex_lock(&qmp->phy_mutex);
@@ -650,6 +822,23 @@  static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
 		qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
 			     SW_PWRDN);
 
+	if (cfg->has_phy_dp_com_ctrl) {
+		qphy_setbits(dp_com, QPHY_V3_DP_COM_POWER_DOWN_CTRL,
+			     SW_PWRDN);
+		/* override hardware control for reset of qmp phy */
+		qphy_setbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+			     SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
+			     SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+
+		qphy_setbits(dp_com, QPHY_V3_DP_COM_PHY_MODE_CTRL,
+			     USB3_MODE | DP_MODE);
+
+		/* bring both QMP USB and QMP DP PHYs PCS block out of reset */
+		qphy_clrbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+			     SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
+			     SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+	}
+
 	/* Serdes configuration */
 	qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
 			       cfg->serdes_tbl_num);
@@ -732,6 +921,7 @@  static int qcom_qmp_phy_init(struct phy *phy)
 	void __iomem *tx = qphy->tx;
 	void __iomem *rx = qphy->rx;
 	void __iomem *pcs = qphy->pcs;
+	void __iomem *dp_com = qmp->dp_com;
 	void __iomem *status;
 	unsigned int mask, val;
 	int ret;
@@ -753,7 +943,16 @@  static int qcom_qmp_phy_init(struct phy *phy)
 
 	/* Tx, Rx, and PCS configurations */
 	qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
+	/* Configuration for other LANE for USB-DP combo PHY */
+	if (cfg->has_phy_dp_com_ctrl)
+		qcom_qmp_phy_configure(tx + cfg->tx_b_lane_offset, cfg->regs,
+				       cfg->tx_tbl, cfg->tx_tbl_num);
+
 	qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
+	if (cfg->has_phy_dp_com_ctrl)
+		qcom_qmp_phy_configure(rx + cfg->rx_b_lane_offset, cfg->regs,
+				       cfg->rx_tbl, cfg->rx_tbl_num);
+
 	qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
 
 	/*
@@ -767,6 +966,8 @@  static int qcom_qmp_phy_init(struct phy *phy)
 
 	/* Pull PHY out of reset state */
 	qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+	if (cfg->has_phy_dp_com_ctrl)
+		qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
 
 	/* start SerDes and Phy-Coding-Sublayer */
 	qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
@@ -1023,6 +1224,9 @@  int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
 	}, {
 		.compatible = "qcom,ipq8074-qmp-pcie-phy",
 		.data = &ipq8074_pciephy_cfg,
+	}, {
+		.compatible = "qcom,qmp-v3-usb3-phy",
+		.data = &qmp_v3_usb3phy_cfg,
 	},
 	{ },
 };
@@ -1046,6 +1250,11 @@  static int qcom_qmp_phy_probe(struct platform_device *pdev)
 	qmp->dev = dev;
 	dev_set_drvdata(dev, qmp);
 
+	/* Get the specific init parameters of QMP phy */
+	qmp->cfg = of_device_get_match_data(dev);
+	if (!qmp->cfg)
+		return -EINVAL;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	base = devm_ioremap_resource(dev, res);
 	if (IS_ERR(base))
@@ -1054,10 +1263,18 @@  static int qcom_qmp_phy_probe(struct platform_device *pdev)
 	/* per PHY serdes; usually located at base address */
 	qmp->serdes = base;
 
-	mutex_init(&qmp->phy_mutex);
+	/* per PHY dp_com; if PHY has dp_com control block */
+	if (qmp->cfg->has_phy_dp_com_ctrl) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						   "dp_com");
+		base = devm_ioremap_resource(dev, res);
+		if (IS_ERR(base))
+			return PTR_ERR(base);
 
-	/* Get the specific init parameters of QMP phy */
-	qmp->cfg = of_device_get_match_data(dev);
+		qmp->dp_com = base;
+	}
+
+	mutex_init(&qmp->phy_mutex);
 
 	ret = qcom_qmp_phy_clk_init(dev);
 	if (ret)