@@ -61,6 +61,19 @@
#define USB3_MODE BIT(0) /* enables USB3 mode */
#define DP_MODE BIT(1) /* enables DP mode */
+/* QPHY_PCS_AUTONOMOUS_MODE_CTRL register bits */
+#define ARCVR_DTCT_EN BIT(0)
+#define ALFPS_DTCT_EN BIT(1)
+#define ARCVR_DTCT_EVENT_SEL BIT(4)
+
+/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */
+#define IRQ_CLEAR BIT(0)
+
+/* QPHY_PCS_LFPS_RXTERM_IRQ_STATUS register bits */
+#define RCVR_DETECT BIT(0)
+
+/* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
+#define CLAMP_EN BIT(0) /* enables i/o clamp_n */
#define PHY_INIT_COMPLETE_TIMEOUT 1000
#define POWER_DOWN_DELAY_US_MIN 10
@@ -108,6 +121,9 @@ enum qphy_reg_layout {
QPHY_SW_RESET,
QPHY_START_CTRL,
QPHY_PCS_READY_STATUS,
+ QPHY_PCS_AUTONOMOUS_MODE_CTRL,
+ QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR,
+ QPHY_PCS_LFPS_RXTERM_IRQ_STATUS,
};
static const unsigned int pciephy_regs_layout[] = {
@@ -135,12 +151,18 @@ enum qphy_reg_layout {
[QPHY_SW_RESET] = 0x00,
[QPHY_START_CTRL] = 0x08,
[QPHY_PCS_READY_STATUS] = 0x17c,
+ [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d4,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0d8,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x178,
};
static const unsigned int qmp_v3_usb3phy_regs_layout[] = {
[QPHY_SW_RESET] = 0x00,
[QPHY_START_CTRL] = 0x08,
[QPHY_PCS_READY_STATUS] = 0x174,
+ [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d8,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0dc,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x170,
};
static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = {
@@ -536,6 +558,7 @@ struct qmp_phy_cfg {
* @tx: iomapped memory space for lane's tx
* @rx: iomapped memory space for lane's rx
* @pcs: iomapped memory space for lane's pcs
+ * @pcs_misc: iomapped memory space for lane's pcs_misc
* @pipe_clk: pipe lock
* @index: lane index
* @qmp: QMP phy to which this lane belongs
@@ -546,6 +569,7 @@ struct qmp_phy {
void __iomem *tx;
void __iomem *rx;
void __iomem *pcs;
+ void __iomem *pcs_misc;
struct clk *pipe_clk;
unsigned int index;
struct qcom_qmp *qmp;
@@ -567,6 +591,8 @@ struct qmp_phy {
* @phys: array of per-lane phy descriptors
* @phy_mutex: mutex lock for PHY common block initialization
* @init_count: phy common block initialization count
+ * @phy_initialized: indicate if PHY has been initialized
+ * @mode: current PHY mode
*/
struct qcom_qmp {
struct device *dev;
@@ -582,6 +608,8 @@ struct qcom_qmp {
struct mutex phy_mutex;
int init_count;
+ bool phy_initialized;
+ enum phy_mode mode;
};
static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val)
@@ -995,6 +1023,7 @@ static int qcom_qmp_phy_init(struct phy *phy)
dev_err(qmp->dev, "phy initialization timed-out\n");
goto err_pcs_ready;
}
+ qmp->phy_initialized = true;
return ret;
@@ -1029,6 +1058,136 @@ static int qcom_qmp_phy_exit(struct phy *phy)
qcom_qmp_phy_com_exit(qmp);
+ qmp->phy_initialized = false;
+
+ return 0;
+}
+
+static int qcom_qmp_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+
+ qmp->mode = mode;
+
+ return 0;
+}
+
+static enum phy_mode qcom_qmp_phy_get_mode(struct phy *phy)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+
+ return qmp->mode;
+}
+
+static void qcom_qmp_phy_enable_autonomous_mode(struct qmp_phy *qphy)
+{
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *pcs = qphy->pcs;
+ void __iomem *pcs_misc = qphy->pcs_misc;
+ u32 intr_mask;
+
+ if (qmp->mode == PHY_MODE_USB_HOST_SS ||
+ qmp->mode == PHY_MODE_USB_DEVICE_SS)
+ intr_mask = ARCVR_DTCT_EN | ALFPS_DTCT_EN;
+ else
+ intr_mask = ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL;
+
+ /* Clear any pending interrupts status */
+ qphy_setbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
+ /* Writing 1 followed by 0 clears the interrupt */
+ qphy_clrbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
+
+ qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL],
+ ARCVR_DTCT_EN | ALFPS_DTCT_EN | ARCVR_DTCT_EVENT_SEL);
+
+ /* Enable required PHY autonomous mode interrupts */
+ qphy_setbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL], intr_mask);
+
+ /* Enable i/o clamp_n for autonomous mode */
+ if (pcs_misc)
+ qphy_clrbits(pcs_misc, QPHY_V3_PCS_MISC_CLAMP_ENABLE, CLAMP_EN);
+}
+
+static void qcom_qmp_phy_disable_autonomous_mode(struct qmp_phy *qphy)
+{
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *pcs = qphy->pcs;
+ void __iomem *pcs_misc = qphy->pcs_misc;
+
+ /* Disable i/o clamp_n on resume for normal mode */
+ if (pcs_misc)
+ qphy_setbits(pcs_misc, QPHY_V3_PCS_MISC_CLAMP_ENABLE, CLAMP_EN);
+
+ qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL],
+ ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL | ALFPS_DTCT_EN);
+
+ qphy_setbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
+ /* Writing 1 followed by 0 clears the interrupt */
+ qphy_clrbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
+}
+
+static int __maybe_unused qcom_qmp_phy_runtime_suspend(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ struct qmp_phy *qphy = qmp->phys[0];
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+
+ dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qmp->mode);
+
+ /* Supported only for USB3 PHY */
+ if (cfg->type != PHY_TYPE_USB3)
+ return 0;
+
+ if (!qmp->phy_initialized) {
+ dev_vdbg(dev, "PHY not initialized, bailing out\n");
+ return 0;
+ }
+
+ qcom_qmp_phy_enable_autonomous_mode(qphy);
+
+ clk_disable_unprepare(qphy->pipe_clk);
+ clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
+
+ return 0;
+}
+
+static int __maybe_unused qcom_qmp_phy_runtime_resume(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ struct qmp_phy *qphy = qmp->phys[0];
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ int ret = 0;
+
+ dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qmp->mode);
+
+ /* Supported only for USB3 PHY */
+ if (cfg->type != PHY_TYPE_USB3)
+ return 0;
+
+ if (!qmp->phy_initialized) {
+ dev_vdbg(dev, "PHY not initialized, bailing out\n");
+ return 0;
+ }
+
+ ret = clk_bulk_prepare_enable(cfg->num_clks, qmp->clks);
+ if (ret) {
+ dev_err(qmp->dev, "failed to enable clks, err=%d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(qphy->pipe_clk);
+ if (ret) {
+ dev_err(dev, "pipe_clk enable failed, err=%d\n", ret);
+ clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
+ return ret;
+ }
+
+ qcom_qmp_phy_disable_autonomous_mode(qphy);
+
return 0;
}
@@ -1142,6 +1301,8 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
.init = qcom_qmp_phy_init,
.exit = qcom_qmp_phy_exit,
.power_on = qcom_qmp_phy_poweron,
+ .set_mode = qcom_qmp_phy_set_mode,
+ .get_mode = qcom_qmp_phy_get_mode,
.owner = THIS_MODULE,
};
@@ -1160,7 +1321,8 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
/*
* Get memory resources for each phy lane:
- * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2.
+ * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2; and
+ * pcs_misc (optional) -> 3.
*/
qphy->tx = of_iomap(np, 0);
if (!qphy->tx)
@@ -1174,6 +1336,10 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
if (!qphy->pcs)
return -ENOMEM;
+ qphy->pcs_misc = of_iomap(np, 3);
+ if (!qphy->pcs_misc)
+ dev_vdbg(dev, "PHY pcs_misc-reg not used\n");
+
/*
* Get PHY's Pipe clock, if any. USB3 and PCIe are PIPE3
* based phys, so they essentially have pipe clock. So,
@@ -1240,6 +1406,11 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
};
MODULE_DEVICE_TABLE(of, qcom_qmp_phy_of_match_table);
+static const struct dev_pm_ops qcom_qmp_phy_pm_ops = {
+ SET_RUNTIME_PM_OPS(qcom_qmp_phy_runtime_suspend,
+ qcom_qmp_phy_runtime_resume, NULL)
+};
+
static int qcom_qmp_phy_probe(struct platform_device *pdev)
{
struct qcom_qmp *qmp;
@@ -1308,12 +1479,21 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
return -ENOMEM;
id = 0;
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+ /*
+ * Prevent runtime pm from being ON by default. Users can enable
+ * it using power/control in sysfs.
+ */
+ pm_runtime_forbid(dev);
+
for_each_available_child_of_node(dev->of_node, child) {
/* Create per-lane phy */
ret = qcom_qmp_phy_create(dev, child, id);
if (ret) {
dev_err(dev, "failed to create lane%d phy, %d\n",
id, ret);
+ pm_runtime_disable(dev);
return ret;
}
@@ -1325,6 +1505,7 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
if (ret) {
dev_err(qmp->dev,
"failed to register pipe clock source\n");
+ pm_runtime_disable(dev);
return ret;
}
id++;
@@ -1333,6 +1514,8 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
if (!IS_ERR(phy_provider))
dev_info(dev, "Registered Qcom-QMP phy\n");
+ else
+ pm_runtime_disable(dev);
return PTR_ERR_OR_ZERO(phy_provider);
}
@@ -1341,6 +1524,7 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
.probe = qcom_qmp_phy_probe,
.driver = {
.name = "qcom-qmp-phy",
+ .pm = &qcom_qmp_phy_pm_ops,
.of_match_table = qcom_qmp_phy_of_match_table,
},
};
@@ -283,4 +283,7 @@
#define QPHY_V3_PCS_FLL_MAN_CODE 0x0d4
#define QPHY_V3_PCS_RX_SIGDET_LVL 0x1d8
+/* Only for QMP V3 PHY - PCS_MISC registers */
+#define QPHY_V3_PCS_MISC_CLAMP_ENABLE 0x0c
+
#endif
Disable clocks and enable PHY autonomous mode to detect wakeup events when PHY is suspended. Core driver should notify speed to PHY driver to enable LFPS and/or RX_DET interrupts. Signed-off-by: Manu Gautam <mgautam@codeaurora.org> --- drivers/phy/qualcomm/phy-qcom-qmp.c | 186 +++++++++++++++++++++++++++++++++++- drivers/phy/qualcomm/phy-qcom-qmp.h | 3 + 2 files changed, 188 insertions(+), 1 deletion(-)