| Message ID | 1522871100-3621-4-git-send-email-austinwc@codeaurora.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
Hi Austin, On 4/5/2018 1:14 AM, Austin Christ wrote: > The I2C spec UM10204 Rev. 6 specifies the following timings. > > Standard Fast Mode Fast Mode Plus > SCL low 4.7us 1.3us 0.5us > SCL high 4.0us 0.6us 0.26us > > This results in a 33%/66% duty cycle as opposed to the 50%/50% duty cycle > used for Standard-mode. > > Add High Time Divider settings to correct duty cycle for FM(400kHz) and > FM+(1MHz). > > Signed-off-by: Austin Christ <austinwc@codeaurora.org> > --- > drivers/i2c/busses/i2c-qup.c | 10 ++++++++-- > 1 file changed, 8 insertions(+), 2 deletions(-) > > diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c > index cb14687..2a88611 100644 > --- a/drivers/i2c/busses/i2c-qup.c > +++ b/drivers/i2c/busses/i2c-qup.c > @@ -1858,9 +1858,15 @@ static int qup_i2c_probe(struct platform_device *pdev) > size = QUP_INPUT_FIFO_SIZE(io_mode); > qup->in_fifo_sz = qup->in_blk_sz * (2 << size); > > - fs_div = ((src_clk_freq / clk_freq) / 2) - 3; > hs_div = 3; > - qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); > + if (clk_freq <= I2C_STANDARD_FREQ) { > + fs_div = ((src_clk_freq / clk_freq) / 2) - 3; > + qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); > + } else { > + /* 33%/66% duty cycle */ > + fs_div = ((src_clk_freq / clk_freq) - 6) * 2 / 3; > + qup->clk_ctl = ((fs_div / 2) << 16) | (hs_div << 8) | (fs_div & 0xff); > + } while here, can we add a small comment for the above calculation. why the -3 above and -6 ? Regards, Sricharan
Hey Sricharan, On 4/13/2018 12:14 AM, Sricharan R wrote: > Hi Austin, > > On 4/5/2018 1:14 AM, Austin Christ wrote: >> The I2C spec UM10204 Rev. 6 specifies the following timings. >> >> Standard Fast Mode Fast Mode Plus >> SCL low 4.7us 1.3us 0.5us >> SCL high 4.0us 0.6us 0.26us >> >> This results in a 33%/66% duty cycle as opposed to the 50%/50% duty cycle >> used for Standard-mode. >> >> Add High Time Divider settings to correct duty cycle for FM(400kHz) and >> FM+(1MHz). >> >> Signed-off-by: Austin Christ <austinwc@codeaurora.org> >> --- >> drivers/i2c/busses/i2c-qup.c | 10 ++++++++-- >> 1 file changed, 8 insertions(+), 2 deletions(-) >> >> diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c >> index cb14687..2a88611 100644 >> --- a/drivers/i2c/busses/i2c-qup.c >> +++ b/drivers/i2c/busses/i2c-qup.c >> @@ -1858,9 +1858,15 @@ static int qup_i2c_probe(struct platform_device *pdev) >> size = QUP_INPUT_FIFO_SIZE(io_mode); >> qup->in_fifo_sz = qup->in_blk_sz * (2 << size); >> >> - fs_div = ((src_clk_freq / clk_freq) / 2) - 3; >> hs_div = 3; >> - qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); >> + if (clk_freq <= I2C_STANDARD_FREQ) { >> + fs_div = ((src_clk_freq / clk_freq) / 2) - 3; >> + qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); >> + } else { >> + /* 33%/66% duty cycle */ >> + fs_div = ((src_clk_freq / clk_freq) - 6) * 2 / 3; >> + qup->clk_ctl = ((fs_div / 2) << 16) | (hs_div << 8) | (fs_div & 0xff); >> + } > while here, can we add a small comment for the above calculation. why the -3 above and -6 ? > Good question. This is the exact math recommended in the HPG for fs_div with and without the high time divider set. There is not explanation for the differences in the math in the hardware documentation that I've seen. What is the preferred way for documenting something like this in comments? > Regards, > Sricharan >
Hi Austin, On 4/13/2018 9:18 PM, Christ, Austin wrote: > Hey Sricharan, > > On 4/13/2018 12:14 AM, Sricharan R wrote: >> Hi Austin, >> >> On 4/5/2018 1:14 AM, Austin Christ wrote: >>> The I2C spec UM10204 Rev. 6 specifies the following timings. >>> >>> Standard Fast Mode Fast Mode Plus >>> SCL low 4.7us 1.3us 0.5us >>> SCL high 4.0us 0.6us 0.26us >>> >>> This results in a 33%/66% duty cycle as opposed to the 50%/50% duty cycle >>> used for Standard-mode. >>> >>> Add High Time Divider settings to correct duty cycle for FM(400kHz) and >>> FM+(1MHz). >>> >>> Signed-off-by: Austin Christ <austinwc@codeaurora.org> >>> --- >>> drivers/i2c/busses/i2c-qup.c | 10 ++++++++-- >>> 1 file changed, 8 insertions(+), 2 deletions(-) >>> >>> diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c >>> index cb14687..2a88611 100644 >>> --- a/drivers/i2c/busses/i2c-qup.c >>> +++ b/drivers/i2c/busses/i2c-qup.c >>> @@ -1858,9 +1858,15 @@ static int qup_i2c_probe(struct platform_device *pdev) >>> size = QUP_INPUT_FIFO_SIZE(io_mode); >>> qup->in_fifo_sz = qup->in_blk_sz * (2 << size); >>> - fs_div = ((src_clk_freq / clk_freq) / 2) - 3; >>> hs_div = 3; >>> - qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); >>> + if (clk_freq <= I2C_STANDARD_FREQ) { >>> + fs_div = ((src_clk_freq / clk_freq) / 2) - 3; >>> + qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); >>> + } else { >>> + /* 33%/66% duty cycle */ >>> + fs_div = ((src_clk_freq / clk_freq) - 6) * 2 / 3; >>> + qup->clk_ctl = ((fs_div / 2) << 16) | (hs_div << 8) | (fs_div & 0xff); >>> + } >> while here, can we add a small comment for the above calculation. why the -3 above and -6 ? >> > Good question. This is the exact math recommended in the HPG for fs_div with and without the high time divider set. There is not explanation for the differences in the math in the hardware documentation that I've seen. What is the preferred way for documenting something like this in comments? ok, so you might have verified clk output with the new settings, right ?. That should be fine. Regards, Sricharan
On 4/17/2018 5:42 AM, Sricharan R wrote: > Hi Austin, > > On 4/13/2018 9:18 PM, Christ, Austin wrote: >> Hey Sricharan, >> >> On 4/13/2018 12:14 AM, Sricharan R wrote: >>> Hi Austin, >>> >>> On 4/5/2018 1:14 AM, Austin Christ wrote: >>>> The I2C spec UM10204 Rev. 6 specifies the following timings. >>>> >>>> Standard Fast Mode Fast Mode Plus >>>> SCL low 4.7us 1.3us 0.5us >>>> SCL high 4.0us 0.6us 0.26us >>>> >>>> This results in a 33%/66% duty cycle as opposed to the 50%/50% duty cycle >>>> used for Standard-mode. >>>> >>>> Add High Time Divider settings to correct duty cycle for FM(400kHz) and >>>> FM+(1MHz). >>>> >>>> Signed-off-by: Austin Christ <austinwc@codeaurora.org> >>>> --- >>>> drivers/i2c/busses/i2c-qup.c | 10 ++++++++-- >>>> 1 file changed, 8 insertions(+), 2 deletions(-) >>>> >>>> diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c >>>> index cb14687..2a88611 100644 >>>> --- a/drivers/i2c/busses/i2c-qup.c >>>> +++ b/drivers/i2c/busses/i2c-qup.c >>>> @@ -1858,9 +1858,15 @@ static int qup_i2c_probe(struct platform_device *pdev) >>>> size = QUP_INPUT_FIFO_SIZE(io_mode); >>>> qup->in_fifo_sz = qup->in_blk_sz * (2 << size); >>>> - fs_div = ((src_clk_freq / clk_freq) / 2) - 3; >>>> hs_div = 3; >>>> - qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); >>>> + if (clk_freq <= I2C_STANDARD_FREQ) { >>>> + fs_div = ((src_clk_freq / clk_freq) / 2) - 3; >>>> + qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); >>>> + } else { >>>> + /* 33%/66% duty cycle */ >>>> + fs_div = ((src_clk_freq / clk_freq) - 6) * 2 / 3; >>>> + qup->clk_ctl = ((fs_div / 2) << 16) | (hs_div << 8) | (fs_div & 0xff); >>>> + } >>> while here, can we add a small comment for the above calculation. why the -3 above and -6 ? >>> >> Good question. This is the exact math recommended in the HPG for fs_div with and without the high time divider set. There is not explanation for the differences in the math in the hardware documentation that I've seen. What is the preferred way for documenting something like this in comments? > > ok, so you might have verified clk output with the new settings, right ?. That should be fine. > Yes clk output was verified as well as the characteristics of the clock signal on the wire for 100kHz, 400kHz, and 1MHz to make sure frequency and duty cycle were within the I2C spec. > Regards, > Sricharan >
diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c index cb14687..2a88611 100644 --- a/drivers/i2c/busses/i2c-qup.c +++ b/drivers/i2c/busses/i2c-qup.c @@ -1858,9 +1858,15 @@ static int qup_i2c_probe(struct platform_device *pdev) size = QUP_INPUT_FIFO_SIZE(io_mode); qup->in_fifo_sz = qup->in_blk_sz * (2 << size); - fs_div = ((src_clk_freq / clk_freq) / 2) - 3; hs_div = 3; - qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); + if (clk_freq <= I2C_STANDARD_FREQ) { + fs_div = ((src_clk_freq / clk_freq) / 2) - 3; + qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); + } else { + /* 33%/66% duty cycle */ + fs_div = ((src_clk_freq / clk_freq) - 6) * 2 / 3; + qup->clk_ctl = ((fs_div / 2) << 16) | (hs_div << 8) | (fs_div & 0xff); + } /* * Time it takes for a byte to be clocked out on the bus.
The I2C spec UM10204 Rev. 6 specifies the following timings. Standard Fast Mode Fast Mode Plus SCL low 4.7us 1.3us 0.5us SCL high 4.0us 0.6us 0.26us This results in a 33%/66% duty cycle as opposed to the 50%/50% duty cycle used for Standard-mode. Add High Time Divider settings to correct duty cycle for FM(400kHz) and FM+(1MHz). Signed-off-by: Austin Christ <austinwc@codeaurora.org> --- drivers/i2c/busses/i2c-qup.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)