@@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-beryllium.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
new file mode 100644
@@ -0,0 +1,382 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/ {
+ model = "Xiaomi Technologies Inc. Beryllium";
+ compatible = "xiaomi,beryllium", "qcom,sdm845";
+
+ /* required for bootloader to select correct board */
+ qcom,board-id = <69 0>;
+ qcom,msm-id = <321 0x20001>;
+
+ aliases {
+ hsuart0 = &uart6;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_up_pin_a>;
+
+ vol-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ vreg_s4a_1p8: vreg-s4a-1p8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+};
+
+&adsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/adsp.mdt";
+};
+
+&apps_rsc {
+ pm8998-rpmh-regulators {
+ compatible = "qcom,pm8998-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_l1a_0p875: ldo1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a_0p8: ldo5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a_2p95: ldo13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17a_1p3: ldo17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l20a_2p95: ldo20 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2968000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l21a_2p95: ldo21 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2968000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l24a_3p075: ldo24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l25a_3p3: ldo25 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l26a_1p2: ldo26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&cdsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/cdsp.mdt";
+};
+
+&gcc {
+ protected-clocks = <GCC_QSPI_CORE_CLK>,
+ <GCC_QSPI_CORE_CLK_SRC>,
+ <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <GCC_LPASS_Q6_AXI_CLK>,
+ <GCC_LPASS_SWAY_CLK>;
+};
+
+&gpu {
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sdm845/a630_zap.mbn";
+ };
+};
+
+/* Reserved memory changes from downstream */
+/delete-node/ &tz_mem;
+/delete-node/ &adsp_mem;
+/delete-node/ &wlan_msa_mem;
+/delete-node/ &mpss_region;
+/delete-node/ &venus_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mba_region;
+/delete-node/ &slpi_mem;
+/delete-node/ &spss_mem;
+/delete-node/ &rmtfs_mem;
+/ {
+ reserved-memory {
+ tz_mem: memory@86200000 {
+ reg = <0 0x86200000 0 0x4900000>;
+ no-map;
+ };
+
+ adsp_mem: memory@8c500000 {
+ reg = <0 0x8c500000 0 0x1e00000>;
+ no-map;
+ };
+
+ wlan_msa_mem: memory@8e300000 {
+ reg = <0 0x8e300000 0 0x100000>;
+ no-map;
+ };
+
+ mpss_region: memory@8e400000 {
+ reg = <0 0x8e400000 0 0x7800000>;
+ no-map;
+ };
+
+ venus_mem: memory@95c00000 {
+ reg = <0 0x95c00000 0 0x500000>;
+ no-map;
+ };
+
+ cdsp_mem: memory@96100000 {
+ reg = <0 0x96100000 0 0x800000>;
+ no-map;
+ };
+
+ mba_region: memory@96900000 {
+ reg = <0 0x96900000 0 0x200000>;
+ no-map;
+ };
+
+ slpi_mem: memory@96b00000 {
+ reg = <0 0x96b00000 0 0x1400000>;
+ no-map;
+ };
+
+ spss_mem: memory@97f00000 {
+ reg = <0 0x97f00000 0 0x100000>;
+ no-map;
+ };
+
+ rmtfs_mem: memory@f6301000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0 0xf6301000 0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+ };
+};
+
+&mss_pil {
+ status = "okay";
+ firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt";
+};
+
+&pm8998_gpio {
+ vol_up_pin_a: vol-up-active {
+ pins = "gpio6";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+};
+
+&pm8998_pon {
+ resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
+
+ vmmc-supply = <&vreg_l21a_2p95>;
+ vqmmc-supply = <&vreg_l13a_2p95>;
+
+ bus-width = <4>;
+ cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ sdc2_default_state: sdc2-default {
+ clk {
+ pins = "sdc2_clk";
+ bias-disable;
+
+ /*
+ * It seems that mmc_test reports errors if drive
+ * strength is not 16 on clk, cmd, and data pins.
+ */
+ drive-strength = <16>;
+ };
+
+ cmd {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+ };
+
+ sdc2_card_det_n: sd-card-det-n {
+ pins = "gpio126";
+ function = "gpio";
+ bias-pull-up;
+ };
+};
+
+&uart6 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l26a_1p2>;
+ vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&ufs_mem_hc {
+ status = "okay";
+
+ reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l20a_2p95>;
+ vcc-max-microamp = <800000>;
+};
+
+&ufs_mem_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&wifi {
+ status = "okay";
+
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qup_uart6_default {
+ pinmux {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "qup6";
+ };
+
+ cts {
+ pins = "gpio45";
+ bias-disable;
+ };
+
+ rts-tx {
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio48";
+ bias-pull-up;
+ };
+};
Add initial dts support for Xiaomi Poco F1 (Beryllium). This initial support is based on upstream Dragonboard 845c (sdm845) device. With this dts, Beryllium boots AOSP up to ADB shell over USB-C. Supported functionality includes UFS, USB-C (peripheral), microSD card and Vol+/Vol-/power keys. Bluetooth should work too but couldn't be verified from adb command line, it is verified when enabled from UI with few WIP display patches. Just like initial db845c support, initializing the SMMU is clearing the mapping used for the splash screen framebuffer, which causes the device to hang during boot and recovery needs a hard power reset. This can be worked around using: fastboot oem select-display-panel none To switch ON the display back run: fastboot oem select-display-panel But this only works on Beryllium devices running bootloader version BOOT.XF.2.0-00369-SDM845LZB-1 that shipped with Android-9 based release. Newer bootloader version do not support switching OFF the display panel at all. So we need a few additional smmu patches (under review) from here: https://github.com/pundiramit/linux/commits/beryllium-mainline Signed-off-by: Amit Pundir <amit.pundir@linaro.org> --- v5: Bumped &tz_mem size from 0x2d00000 to 0x4900000 (to include downstream &removed_region), all the way up to &qseecom_mem. v4: Added more downstream reserved memory regions. It probably need more work, but for now I see adsp/cdsp/wlan remoteprocs powering up properly. Removed the regulator nodes not required for the device, as suggested by Bjorn. Also added couple of clocks to protected clocks, which is needed for display to work. v3: Added a reserved-memory region from downstream kernel to fix a boot regression with recent dma-pool changes in v5.8-rc6. v2: Updated machine compatible string for seemingly inevitable future quirks. arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/sdm845-beryllium.dts | 382 ++++++++++++++++++++++++++ 2 files changed, 383 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sdm845-beryllium.dts