new file mode 100644
@@ -0,0 +1,235 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dpu-sc7180.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DPU dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
+ sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
+ bindings of MDSS and DPU are mentioned for SC7180 target.
+
+properties:
+ compatible:
+ items:
+ - const: qcom,sc7180-mdss
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: mdss
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ maxItems: 3
+
+ clock-names:
+ items:
+ - const: iface
+ - const: ahb
+ - const: core
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 1
+
+ iommus:
+ maxItems: 1
+
+ "#address-cells":
+ const: 2
+
+ "#size-cells":
+ const: 2
+
+ ranges: true
+
+ interconnects:
+ description: |
+ Interconnect path specifier for MDSS according to
+ Documentation/devicetree/bindings/interconnect/interconnect.txt.
+ An entry should contain 2 paths corresponding to 2 AXI ports representing
+ source and destination ports.
+ minItems: 1
+
+ interconnect-names:
+ description: |
+ MDSS will have 2 port names to differentiate between the
+ 2 interconnect paths defined with interconnect specifier.
+ items:
+ - const: mdp0-mem
+
+ assigned-clocks:
+ maxItems: 1
+
+ assigned-clock-rates:
+ maxItems: 1
+
+patternProperties:
+ "^mdp@[0-9a-f]+$":
+ type: object
+ description: Node containing the properties of DPU.
+
+ properties:
+ compatible:
+ items:
+ - const: qcom,sc7180-dpu
+
+ reg:
+ maxItems: 2
+
+ reg-names:
+ items:
+ - const: mdp
+ - const: vbif
+
+ clocks:
+ maxItems: 6
+
+ clock-names:
+ description: |
+ Device clock names, must be in same order as clocks property.
+ The following clocks are required.
+ items:
+ - const: bus
+ - const: iface
+ - const: rot
+ - const: lut
+ - const: core
+ - const: vsync
+
+ interrupts:
+ maxItems: 1
+
+ ports:
+ type: object
+ description: |
+ Contains the list of output ports from DPU device. These ports
+ connect to interfaces that are external to the DPU hardware,
+ such as DSI, DP etc. Each output port contains an endpoint that
+ describes how it is connected to an external interface. These
+ are described by the standard properties documented in files
+ mentioned below.
+
+ Documentation/devicetree/bindings/graph.txt
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+ properties:
+ port@0:
+ type: object
+ description: DPU_INTF1 (DSI1)
+ port@1:
+ type: object
+ description: DPU_INTF2 (DSI2)
+
+ assigned-clocks:
+ maxItems: 4
+
+ assigned-clock-rates:
+ maxItems: 4
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - power-domains
+ - clocks
+ - clock-names
+ - interrupts
+ - interrupt-controller
+ - iommus
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
+ #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interconnect/qcom,sdm845.h>
+
+ soc: soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ mdss: mdss@ae00000 {
+ compatible = "qcom,sc7180-mdss";
+ reg = <0 0xae00000 0 0x1000>;
+ reg-names = "mdss";
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+ clock-names = "iface", "ahb", "core";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ assigned-clock-rates = <300000000>;
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interconnects = <&mmss_noc MASTER_MDP0 &mc_virt SLAVE_EBI1>;
+
+ interconnect-names = "mdp0-mem";
+
+ iommus = <&apps_smmu 0x800 0x2>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ mdp: mdp@ae01000 {
+ compatible = "qcom,sc7180-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_ROT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus", "iface", "rot", "lut", "core",
+ "vsync";
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>,
+ <&dispcc DISP_CC_MDSS_ROT_CLK>,
+ <&dispcc DISP_CC_MDSS_ROT_CLK>;
+ assigned-clock-rates = <300000000>,
+ <19200000>,
+ <19200000>,
+ <19200000>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+ };
+ };
+...
new file mode 100644
@@ -0,0 +1,216 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dpu-sdm845.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DPU dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
+ sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
+ bindings of MDSS and DPU are mentioned for SDM845 target.
+
+properties:
+ compatible:
+ items:
+ - const: qcom,sdm845-mdss
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: mdss
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ maxItems: 3
+
+ clock-names:
+ description: |
+ Device clock names in the same order as mentioned in clocks property.
+ The required clocks are mentioned below.
+ items:
+ - const: iface
+ - const: bus
+ - const: core
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 1
+
+ iommus:
+ maxItems: 2
+
+ "#address-cells":
+ const: 2
+
+ "#size-cells":
+ const: 2
+
+ ranges: true
+
+ assigned-clocks:
+ maxItems: 1
+
+ assigned-clock-rates:
+ maxItems: 1
+
+patternProperties:
+ "^mdp@[0-9a-f]+$":
+ type: object
+ description: Node containing the properties of DPU.
+
+ properties:
+ compatible:
+ items:
+ - const: qcom,sdm845-dpu
+ reg:
+ maxItems: 2
+
+ reg-names:
+ items:
+ - const: mdp
+ - const: vbif
+
+ clocks:
+ maxItems: 4
+
+ clock-names:
+ description: |
+ Device clock names, must be in same order as clocks property.
+ The following clocks are required.
+ items:
+ - const: iface
+ - const: bus
+ - const: core
+ - const: vsync
+
+ interrupts:
+ maxItems: 1
+
+ ports:
+ type: object
+ description: |
+ Contains the list of output ports from DPU device. These ports
+ connect to interfaces that are external to the DPU hardware,
+ such as DSI, DP etc. Each output port contains an endpoint that
+ describes how it is connected to an external interface. These
+ are described by the standard properties documented in files
+ mentioned below.
+
+ Documentation/devicetree/bindings/graph.txt
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+ properties:
+ port@0:
+ type: object
+ description: DPU_INTF1 (DSI1)
+ port@1:
+ type: object
+ description: DPU_INTF2 (DSI2)
+
+ assigned-clocks:
+ maxItems: 2
+
+ assigned-clock-rates:
+ maxItems: 2
+
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - power-domains
+ - clocks
+ - clock-names
+ - interrupts
+ - interrupt-controller
+ - iommus
+
+additionalProperties: false
+
+examples:
+- |
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ soc: soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ mdss: mdss@ae00000 {
+ compatible = "qcom,sdm845-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&gcc GCC_DISP_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "bus", "core";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ assigned-clock-rates = <300000000>;
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_smmu 0x880 0x8>,
+ <&apps_smmu 0xc80 0x8>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ mdss_mdp: mdp@ae01000 {
+ compatible = "qcom,sdm845-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "iface", "bus", "core", "vsync";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <300000000>,
+ <19200000>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&dsi1_in>;
+ };
+ };
+ };
+ };
+ };
+ };
+...
deleted file mode 100644
@@ -1,141 +0,0 @@
-Qualcomm Technologies, Inc. DPU KMS
-
-Description:
-
-Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
-sub-blocks like DPU display controller, DSI and DP interfaces etc.
-The DPU display controller is found in SDM845 SoC.
-
-MDSS:
-Required properties:
-- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss"
-- reg: physical base address and length of contoller's registers.
-- reg-names: register region names. The following region is required:
- * "mdss"
-- power-domains: a power domain consumer specifier according to
- Documentation/devicetree/bindings/power/power_domain.txt
-- clocks: list of clock specifiers for clocks needed by the device.
-- clock-names: device clock names, must be in same order as clocks property.
- The following clocks are required:
- * "iface"
- * "bus"
- * "core"
-- interrupts: interrupt signal from MDSS.
-- interrupt-controller: identifies the node as an interrupt controller.
-- #interrupt-cells: specifies the number of cells needed to encode an interrupt
- source, should be 1.
-- iommus: phandle of iommu device node.
-- #address-cells: number of address cells for the MDSS children. Should be 1.
-- #size-cells: Should be 1.
-- ranges: parent bus address space is the same as the child bus address space.
-- interconnects : interconnect path specifier for MDSS according to
- Documentation/devicetree/bindings/interconnect/interconnect.txt. Should be
- 2 paths corresponding to 2 AXI ports.
-- interconnect-names : MDSS will have 2 port names to differentiate between the
- 2 interconnect paths defined with interconnect specifier.
-
-Optional properties:
-- assigned-clocks: list of clock specifiers for clocks needing rate assignment
-- assigned-clock-rates: list of clock frequencies sorted in the same order as
- the assigned-clocks property.
-
-MDP:
-Required properties:
-- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu"
-- reg: physical base address and length of controller's registers.
-- reg-names : register region names. The following region is required:
- * "mdp"
- * "vbif"
-- clocks: list of clock specifiers for clocks needed by the device.
-- clock-names: device clock names, must be in same order as clocks property.
- The following clocks are required.
- * "bus"
- * "iface"
- * "core"
- * "vsync"
-- interrupts: interrupt line from DPU to MDSS.
-- ports: contains the list of output ports from DPU device. These ports connect
- to interfaces that are external to the DPU hardware, such as DSI, DP etc.
-
- Each output port contains an endpoint that describes how it is connected to an
- external interface. These are described by the standard properties documented
- here:
- Documentation/devicetree/bindings/graph.txt
- Documentation/devicetree/bindings/media/video-interfaces.txt
-
- Port 0 -> DPU_INTF1 (DSI1)
- Port 1 -> DPU_INTF2 (DSI2)
-
-Optional properties:
-- assigned-clocks: list of clock specifiers for clocks needing rate assignment
-- assigned-clock-rates: list of clock frequencies sorted in the same order as
- the assigned-clocks property.
-
-Example:
-
- mdss: mdss@ae00000 {
- compatible = "qcom,sdm845-mdss";
- reg = <0xae00000 0x1000>;
- reg-names = "mdss";
-
- power-domains = <&clock_dispcc 0>;
-
- clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>,
- <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
- clock-names = "iface", "bus", "core";
-
- assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
- assigned-clock-rates = <300000000>;
-
- interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-controller;
- #interrupt-cells = <1>;
-
- interconnects = <&rsc_hlos MASTER_MDP0 &rsc_hlos SLAVE_EBI1>,
- <&rsc_hlos MASTER_MDP1 &rsc_hlos SLAVE_EBI1>;
-
- interconnect-names = "mdp0-mem", "mdp1-mem";
-
- iommus = <&apps_iommu 0>;
-
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0xae00000 0xb2008>;
-
- mdss_mdp: mdp@ae01000 {
- compatible = "qcom,sdm845-dpu";
- reg = <0 0x1000 0x8f000>, <0 0xb0000 0x2008>;
- reg-names = "mdp", "vbif";
-
- clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>,
- <&clock_dispcc DISP_CC_MDSS_AXI_CLK>,
- <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
- <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
- clock-names = "iface", "bus", "core", "vsync";
-
- assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
- <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
- assigned-clock-rates = <0 0 300000000 19200000>;
-
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- dpu_intf1_out: endpoint {
- remote-endpoint = <&dsi0_in>;
- };
- };
-
- port@1 {
- reg = <1>;
- dpu_intf2_out: endpoint {
- remote-endpoint = <&dsi1_in>;
- };
- };
- };
- };
- };
new file mode 100644
@@ -0,0 +1,235 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-common-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DSI controller dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Common Device tree bindings for DSI controller.
+
+allOf:
+ - $ref: "../dsi-controller.yaml#"
+
+properties:
+ compatible:
+ items:
+ - const: qcom,mdss-dsi-ctrl
+
+ vdd-supply:
+ description: Phandle to vdd regulator device node.
+
+ vddio-supply:
+ description: Phandle to vdd-io regulator device node.
+
+ vdda-supply:
+ description: Phandle to vdda regulator device node.
+
+ phys:
+ description: Phandle to DSI PHY device node.
+ maxItems: 1
+
+ phy-names:
+ description: Name of the corresponding PHY device.
+ maxItems: 1
+
+ syscon-sfpb:
+ description: A phandle to mmss_sfpb syscon node (only for DSIv2).
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ # Optional Properties for dsi controller
+ qcom,mdss-mdp-transfer-time-us:
+ description: |
+ Specifies the DSI transfer time for command mode
+ panels in microseconds. Driver uses this number to adjust
+ the clock rate according to the expected transfer time.
+ Increasing this value would slow down the mdp processing
+ and can result in slower performance.
+ Decreasing this value can speed up the mdp processing,
+ but this can also impact power consumption.
+ As a rule this time should not be higher than the time
+ that would be expected with the processing at the
+ DSI link rate since anyways this would be the maximum
+ transfer time that could be achieved.
+ If ping pong split is enabled, this time should not be higher
+ than two times the DSI link rate time.
+ This is an optional property.
+ default: 14000
+
+ qcom,dual-dsi-mode:
+ type: boolean
+ description: |
+ Boolean value indicating if the DSI controller is
+ driving a panel which needs 2 DSI links.
+
+ qcom,master-dsi:
+ type: boolean
+ description: |
+ Boolean value indicating if the DSI controller is driving
+ the master link of the 2-DSI panel.
+
+ qcom,sync-dual-dsi:
+ type: boolean
+ description: |
+ Boolean value indicating if the DSI controller is driving a
+ 2-DSI panel whose 2 links need receive command simultaneously.
+
+ pinctrl-names:
+ description: The pin control state names.
+ items:
+ - const: default
+ - const: sleep
+
+ pinctrl-0:
+ description: The default pinctrl state (active)
+
+ pinctrl-1:
+ description: The sleep pinctrl state (suspend)
+
+ ports:
+ type: object
+ description: |
+ Contains DSI controller input and output ports as children, each
+ containing one endpoint subnode as defined in
+ Documentation/devicetree/bindings/graph.txt and
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+ properties:
+ port@0:
+ type: object
+ description: |
+ Input endpoints of the controller.
+
+ properties:
+ reg:
+ const: 0
+
+ endpoint:
+ type: object
+ properties:
+ remote-endpoint:
+ description: |
+ For port@0, set to phandle of the connected panel/bridge's
+ input endpoint. For port@1, set to the MDP interface output.
+ See Documentation/devicetree/bindings/graph.txt for
+ device graph info.
+
+ data-lanes:
+ description: |
+ This describes how the physical DSI data lanes are mapped
+ to the logical lanes on the given platform. The value contained in
+ index n describes what physical lane is mapped to the logical lane n
+ (DATAn, where n lies between 0 and 3). The clock lane position is fixed
+ and can't be changed. Hence, they aren't a part of the DT bindings. See
+ Documentation/devicetree/bindings/media/video-interfaces.txt for
+ more info on the data-lanes property.
+
+ For example:
+ data-lanes = <3 0 1 2>;
+
+ The above mapping describes that the logical data lane DATA0 is mapped
+ to the physical data lane DATA3, logical DATA1 to physical DATA0,
+ logic DATA2 to phys DATA1 and logic DATA3 to phys DATA2. There are
+ only a limited number of physical to logical mappings possible.
+ oneOf:
+ - items:
+ - const: 0
+ - const: 1
+ - const: 2
+ - const: 3
+ - items:
+ - const: 1
+ - const: 2
+ - const: 3
+ - const: 0
+ - items:
+ - const: 2
+ - const: 3
+ - const: 0
+ - const: 1
+ - items:
+ - const: 3
+ - const: 0
+ - const: 1
+ - const: 2
+ - items:
+ - const: 0
+ - const: 3
+ - const: 2
+ - const: 1
+ - items:
+ - const: 1
+ - const: 0
+ - const: 3
+ - const: 2
+ - items:
+ - const: 2
+ - const: 1
+ - const: 0
+ - const: 3
+ - items:
+ - const: 3
+ - const: 2
+ - const: 1
+ - const: 0
+ port@1:
+ type: object
+ description: |
+ Output endpoints of the controller.
+ properties:
+ reg:
+ const: 1
+
+ endpoint:
+ type: object
+ properties:
+ remote-endpoint: true
+ data-lanes:
+ oneOf:
+ - items:
+ - const: 0
+ - const: 1
+ - const: 2
+ - const: 3
+ - items:
+ - const: 1
+ - const: 2
+ - const: 3
+ - const: 0
+ - items:
+ - const: 2
+ - const: 3
+ - const: 0
+ - const: 1
+ - items:
+ - const: 3
+ - const: 0
+ - const: 1
+ - const: 2
+ - items:
+ - const: 0
+ - const: 3
+ - const: 2
+ - const: 1
+ - items:
+ - const: 1
+ - const: 0
+ - const: 3
+ - const: 2
+ - items:
+ - const: 2
+ - const: 1
+ - const: 0
+ - const: 3
+ - items:
+ - const: 3
+ - const: 2
+ - const: 1
+ - const: 0
+
+unevaluatedProperties: false
+...
new file mode 100644
@@ -0,0 +1,119 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-controller-main.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DSI controller dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Device tree bindings for DSI controller.
+
+allOf:
+ - $ref: dsi-common-controller.yaml#
+
+properties:
+ compatible:
+ const: qcom,mdss-dsi-ctrl
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: dsi_ctrl
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 6
+
+ clock-names:
+ items:
+ - const: byte
+ - const: byte_intf
+ - const: pixel
+ - const: core
+ - const: iface
+ - const: bus
+
+ phys:
+ maxItems: 1
+
+ phy-names:
+ const: dsi
+
+ ports: true
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - interrupts
+ - clocks
+ - clock-names
+ - phys
+ - phy-names
+ - ports
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+
+ mdss: mdss {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ phys = <&dsi0_phy>;
+ phy-names = "dsi";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+ };
+...
new file mode 100644
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-10nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DSI 10nm PHY dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Common Device tree bindings for DSI 10nm PHY.
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,dsi-phy-10nm
+ - const: qcom,dsi-phy-10nm-8998
+
+ reg-names:
+ items:
+ - const: dsi_phy
+ - const: dsi_phy_lane
+ - const: dsi_pll
+
+ clock-cells:
+ description: |
+ The DSI PHY block acts as a clock provider, creating
+ 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
+ const: 1
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ description: |
+ The following clocks are required.
+ items:
+ - const: iface
+ - const: ref
+
+ vdds-supply:
+ description: |
+ Phandle to vdds regulator device node.
+
+ qcom,dsi-phy-regulator-ldo-mode:
+ type: boolean
+ description: |
+ Boolean value indicating if the LDO mode PHY regulator is wanted (optional).
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - vdds-supply
+
+additionalProperties: true
+...
new file mode 100644
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-14nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DSI 14nm PHY dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Common Device tree bindings for DSI 14nm PHY.
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,dsi-phy-14nm
+ - const: qcom,dsi-phy-14nm-660
+
+ reg-names:
+ items:
+ - const: dsi_phy
+ - const: dsi_phy_lane
+ - const: dsi_pll
+
+ clock-cells:
+ description: |
+ The DSI PHY block acts as a clock provider, creating
+ 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
+ const: 1
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ description: |
+ The following clocks are required.
+ items:
+ - const: iface
+ - const: ref
+
+ qcom,dsi-phy-regulator-ldo-mode:
+ type: boolean
+ description: |
+ Boolean value indicating if the LDO mode PHY regulator is wanted (optional).
+
+ vcca-supply:
+ description: |
+ Phandle to vcca regulator device node.
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - vcca-supply
+
+additionalProperties: true
+...
new file mode 100644
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-20nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DSI 20nm PHY dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Common Device tree bindings for DSI 20nm PHY.
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,dsi-phy-20nm
+
+ reg-names:
+ items:
+ - const: dsi_pll
+ - const: dsi_phy
+ - const: dsi_phy_regulator
+
+ clock-cells:
+ description: |
+ The DSI PHY block acts as a clock provider, creating
+ 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
+ const: 1
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ description: |
+ The following clocks are required.
+ items:
+ - const: iface
+ - const: ref
+
+ qcom,dsi-phy-regulator-ldo-mode:
+ type: boolean
+ description: |
+ Boolean value indicating if the LDO mode PHY regulator is wanted (optional).
+
+ vcca-supply:
+ description: |
+ Phandle to vcca regulator device node.
+
+ vddio-supply:
+ description: |
+ Phandle to vdd-io regulator device node.
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - vddio-supply
+ - vcca-supply
+
+additionalProperties: true
+...
new file mode 100644
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-28nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DSI 28nm PHY dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Common Device tree bindings for DSI 28nm PHY.
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,dsi-phy-28nm-hpm
+ - const: qcom,dsi-phy-28nm-lp
+ - const: qcom,dsi-phy-28nm-8960
+
+ reg-names:
+ items:
+ - const: dsi_pll
+ - const: dsi_phy
+ - const: dsi_phy_regulator
+
+ clock-cells:
+ description: |
+ The DSI PHY block acts as a clock provider, creating
+ 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
+ const: 1
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ description: |
+ The following clocks are required.
+ items:
+ - const: iface
+ - const: ref
+
+ qcom,dsi-phy-regulator-ldo-mode:
+ type: boolean
+ description: |
+ Boolean value indicating if the LDO mode PHY regulator is wanted (optional).
+
+ vddio-supply:
+ description: |
+ Phandle to vdd-io regulator device node.
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - vddio-supply
+
+additionalProperties: true
+...
new file mode 100644
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DSI PHY dt properties.
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Device tree bindings for DSI PHY.
+
+allOf:
+ - $ref: dsi-phy-10nm.yaml#
+
+properties:
+ compatible:
+ const: qcom,dsi-phy-10nm
+
+ reg:
+ maxItems: 3
+
+ reg-names:
+ maxItems: 3
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: iface
+ - const: ref
+
+ "#clock-cells":
+ const: 1
+
+ "#phy-cells":
+ const: 0
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,rpmh.h>
+
+ mdss: mdss {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ dsi0_phy: dsi-phy@ae94400 {
+ compatible = "qcom,dsi-phy-10nm";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94a00 0 0x1e0>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ vdds-supply = <&vdda_mipi_dsi0_pll>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ };
+ };
+...
deleted file mode 100644
@@ -1,249 +0,0 @@
-Qualcomm Technologies Inc. adreno/snapdragon DSI output
-
-DSI Controller:
-Required properties:
-- compatible:
- * "qcom,mdss-dsi-ctrl"
-- reg: Physical base address and length of the registers of controller
-- reg-names: The names of register regions. The following regions are required:
- * "dsi_ctrl"
-- interrupts: The interrupt signal from the DSI block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks.
-- clock-names: the following clocks are required:
- * "mdp_core"
- * "iface"
- * "bus"
- * "core_mmss"
- * "byte"
- * "pixel"
- * "core"
- For DSIv2, we need an additional clock:
- * "src"
- For DSI6G v2.0 onwards, we need also need the clock:
- * "byte_intf"
-- assigned-clocks: Parents of "byte" and "pixel" for the given platform.
-- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
- by a DSI PHY block. See [1] for details on clock bindings.
-- vdd-supply: phandle to vdd regulator device node
-- vddio-supply: phandle to vdd-io regulator device node
-- vdda-supply: phandle to vdda regulator device node
-- phys: phandle to DSI PHY device node
-- phy-names: the name of the corresponding PHY device
-- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
-- ports: Contains 2 DSI controller ports as child nodes. Each port contains
- an endpoint subnode as defined in [2] and [3].
-
-Optional properties:
-- panel@0: Node of panel connected to this DSI controller.
- See files in [4] for each supported panel.
-- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
- driving a panel which needs 2 DSI links.
-- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
- the master link of the 2-DSI panel.
-- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
- driving a 2-DSI panel whose 2 links need receive command simultaneously.
-- pinctrl-names: the pin control state names; should contain "default"
-- pinctrl-0: the default pinctrl state (active)
-- pinctrl-n: the "sleep" pinctrl state
-- ports: contains DSI controller input and output ports as children, each
- containing one endpoint subnode.
-
- DSI Endpoint properties:
- - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
- input endpoint. For port@1, set to the MDP interface output. See [2] for
- device graph info.
-
- - data-lanes: this describes how the physical DSI data lanes are mapped
- to the logical lanes on the given platform. The value contained in
- index n describes what physical lane is mapped to the logical lane n
- (DATAn, where n lies between 0 and 3). The clock lane position is fixed
- and can't be changed. Hence, they aren't a part of the DT bindings. See
- [3] for more info on the data-lanes property.
-
- For example:
-
- data-lanes = <3 0 1 2>;
-
- The above mapping describes that the logical data lane DATA0 is mapped to
- the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
- to phys DATA1 and logic DATA3 to phys DATA2.
-
- There are only a limited number of physical to logical mappings possible:
- <0 1 2 3>
- <1 2 3 0>
- <2 3 0 1>
- <3 0 1 2>
- <0 3 2 1>
- <1 0 3 2>
- <2 1 0 3>
- <3 2 1 0>
-
-DSI PHY:
-Required properties:
-- compatible: Could be the following
- * "qcom,dsi-phy-28nm-hpm"
- * "qcom,dsi-phy-28nm-lp"
- * "qcom,dsi-phy-20nm"
- * "qcom,dsi-phy-28nm-8960"
- * "qcom,dsi-phy-14nm"
- * "qcom,dsi-phy-14nm-660"
- * "qcom,dsi-phy-10nm"
- * "qcom,dsi-phy-10nm-8998"
- * "qcom,dsi-phy-7nm"
- * "qcom,dsi-phy-7nm-8150"
-- reg: Physical base address and length of the registers of PLL, PHY. Some
- revisions require the PHY regulator base address, whereas others require the
- PHY lane base address. See below for each PHY revision.
-- reg-names: The names of register regions. The following regions are required:
- For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
- * "dsi_pll"
- * "dsi_phy"
- * "dsi_phy_regulator"
- For DSI 14nm, 10nm and 7nm PHYs:
- * "dsi_pll"
- * "dsi_phy"
- * "dsi_phy_lane"
-- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
- 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks. See [1] for details on clock bindings.
-- clock-names: the following clocks are required:
- * "iface"
- * "ref" (only required for new DTS files/entries)
- For 28nm HPM/LP, 28nm 8960 PHYs:
-- vddio-supply: phandle to vdd-io regulator device node
- For 20nm PHY:
-- vddio-supply: phandle to vdd-io regulator device node
-- vcca-supply: phandle to vcca regulator device node
- For 14nm PHY:
-- vcca-supply: phandle to vcca regulator device node
- For 10nm and 7nm PHY:
-- vdds-supply: phandle to vdds regulator device node
-
-Optional properties:
-- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
- regulator is wanted.
-- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode
- panels in microseconds. Driver uses this number to adjust
- the clock rate according to the expected transfer time.
- Increasing this value would slow down the mdp processing
- and can result in slower performance.
- Decreasing this value can speed up the mdp processing,
- but this can also impact power consumption.
- As a rule this time should not be higher than the time
- that would be expected with the processing at the
- dsi link rate since anyways this would be the maximum
- transfer time that could be achieved.
- If ping pong split is enabled, this time should not be higher
- than two times the dsi link rate time.
- If the property is not specified, then the default value is 14000 us.
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/graph.txt
-[3] Documentation/devicetree/bindings/media/video-interfaces.txt
-[4] Documentation/devicetree/bindings/display/panel/
-
-Example:
- dsi0: dsi@fd922800 {
- compatible = "qcom,mdss-dsi-ctrl";
- qcom,dsi-host-index = <0>;
- interrupt-parent = <&mdp>;
- interrupts = <4 0>;
- reg-names = "dsi_ctrl";
- reg = <0xfd922800 0x200>;
- power-domains = <&mmcc MDSS_GDSC>;
- clock-names =
- "bus",
- "byte",
- "core",
- "core_mmss",
- "iface",
- "mdp_core",
- "pixel";
- clocks =
- <&mmcc MDSS_AXI_CLK>,
- <&mmcc MDSS_BYTE0_CLK>,
- <&mmcc MDSS_ESC0_CLK>,
- <&mmcc MMSS_MISC_AHB_CLK>,
- <&mmcc MDSS_AHB_CLK>,
- <&mmcc MDSS_MDP_CLK>,
- <&mmcc MDSS_PCLK0_CLK>;
-
- assigned-clocks =
- <&mmcc BYTE0_CLK_SRC>,
- <&mmcc PCLK0_CLK_SRC>;
- assigned-clock-parents =
- <&dsi_phy0 0>,
- <&dsi_phy0 1>;
-
- vdda-supply = <&pma8084_l2>;
- vdd-supply = <&pma8084_l22>;
- vddio-supply = <&pma8084_l12>;
-
- phys = <&dsi_phy0>;
- phy-names ="dsi-phy";
-
- qcom,dual-dsi-mode;
- qcom,master-dsi;
- qcom,sync-dual-dsi;
-
- qcom,mdss-mdp-transfer-time-us = <12000>;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&dsi_active>;
- pinctrl-1 = <&dsi_suspend>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- dsi0_in: endpoint {
- remote-endpoint = <&mdp_intf1_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- dsi0_out: endpoint {
- remote-endpoint = <&panel_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
-
- panel: panel@0 {
- compatible = "sharp,lq101r1sx01";
- reg = <0>;
- link2 = <&secondary>;
-
- power-supply = <...>;
- backlight = <...>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
- };
-
- dsi_phy0: dsi-phy@fd922a00 {
- compatible = "qcom,dsi-phy-28nm-hpm";
- qcom,dsi-phy-index = <0>;
- reg-names =
- "dsi_pll",
- "dsi_phy",
- "dsi_phy_regulator";
- reg = <0xfd922a00 0xd4>,
- <0xfd922b00 0x2b0>,
- <0xfd922d80 0x7b>;
- clock-names = "iface";
- clocks = <&mmcc MDSS_AHB_CLK>;
- #clock-cells = <1>;
- vddio-supply = <&pma8084_l12>;
-
- qcom,dsi-phy-regulator-ldo-mode;
- };
MSM Mobile Display Subsytem (MDSS) encapsulates sub-blocks like DPU display controller, DSI etc. Add YAML schema for the device tree bindings for the same. Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org> Changes in v2: - Changed dpu to DPU (Sam Ravnborg) - Fixed indentation issues (Sam Ravnborg) - Added empty line between different properties (Sam Ravnborg) - Replaced reference txt files with their corresponding yaml files (Sam Ravnborg) - Modified the file to use "|" only when it is necessary (Sam Ravnborg) Changes in v3: - Corrected the license used (Rob Herring) - Added maxItems for properties (Rob Herring) - Dropped generic descriptions (Rob Herring) - Added ranges property (Rob Herring) - Corrected the indendation (Rob Herring) - Added additionalProperties (Rob Herring) - Split dsi file into two, one for dsi controller and another one for dsi phy per target (Rob Herring) - Corrected description for pinctrl-names (Rob Herring) - Corrected the examples used in yaml file (Rob Herring) - Delete dsi.txt and dpu.txt (Rob Herring) Changes in v4: - Move schema up by one level (Rob Herring) - Add patternProperties for mdp node (Rob Herring) - Corrected description of some properties (Rob Herring) Changes in v5: - Correct the indentation (Rob Herring) - Remove unnecessary description from properties (Rob Herring) - Correct the number of interconnect entries (Rob Herring) - Add interconnect names for sc7180 (Rob Herring) - Add description for ports (Rob Herring) - Remove common properties (Rob Herring) - Add unevalutatedProperties (Rob Herring) - Reference existing dsi controller yaml in the common dsi controller file (Rob Herring) - Correct the description of clock names to include only the clocks that are required (Rob Herring) - Remove properties which are already covered under the common binding (Rob Herring) - Add dsi phy supply nodes which are required for sc7180 and sdm845 targets (Rob Herring) - Add type ref for syscon-sfpb (Rob Herring) Changes in v6: - Fixed errors during dt_binding_check (Rob Herring) - Add maxItems for phys and phys-names (Rob Herring) - Use unevaluatedProperties wherever required (Rob Herring) - Removed interrupt controller from required properties for dsi controller (Rob Herring) - Add constraints for dsi-phy reg-names based on the compatible phy version (Rob Herring) - Add constraints for dsi-phy supply nodes based on the compatible phy version (Rob Herring) Changes in v7: - Add default value for qcom,mdss-mdp-transfer-time-us (Rob Herring) - Modify the schema for data-lanes (Rob Herring) - Split the phy schema into separate schemas based on the phy version (Rob Herring) Changes in v8: - Resolve merge conflicts with latest dsi.txt file - Include dp yaml change also in the same series Changes in v9: - Combine target specific dsi controller yaml files to a single yaml file (Rob Herring) - Combine target specific dsi phy yaml files into a single yaml file (Rob Herring) - Use unevaluatedProperties and additionalProperties wherever required - Remove duplicate properties from common yaml files --- .../bindings/display/msm/dpu-sc7180.yaml | 235 +++++++++++++++++++ .../bindings/display/msm/dpu-sdm845.yaml | 216 ++++++++++++++++++ .../devicetree/bindings/display/msm/dpu.txt | 141 ------------ .../display/msm/dsi-common-controller.yaml | 235 +++++++++++++++++++ .../bindings/display/msm/dsi-controller-main.yaml | 119 ++++++++++ .../bindings/display/msm/dsi-phy-10nm.yaml | 64 ++++++ .../bindings/display/msm/dsi-phy-14nm.yaml | 64 ++++++ .../bindings/display/msm/dsi-phy-20nm.yaml | 68 ++++++ .../bindings/display/msm/dsi-phy-28nm.yaml | 64 ++++++ .../devicetree/bindings/display/msm/dsi-phy.yaml | 81 +++++++ .../devicetree/bindings/display/msm/dsi.txt | 249 --------------------- 11 files changed, 1146 insertions(+), 390 deletions(-) create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml delete mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-common-controller.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy.yaml delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt