| Message ID | 1621332225-31918-2-git-send-email-mkrishn@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v16,1/4] dt-bindings: msm: disp: add yaml schemas for DPU bindings | expand |
On Tue, May 18, 2021 at 03:33:43PM +0530, Krishna Manikandan wrote: > Add YAML schema for the device tree bindings for DSI > > Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org> > > Changes in v1: > - Separate dsi controller bindings to a separate patch (Stephen Boyd) > - Merge dsi-common-controller.yaml and dsi-controller-main.yaml to > a single file (Stephen Boyd) > - Drop supply entries and definitions from properties (Stephen Boyd) > - Modify phy-names property for dsi controller (Stephen Boyd) > - Remove boolean from description (Stephen Boyd) > - Drop pinctrl properties as they are standard entries (Stephen Boyd) > - Modify the description for ports property and keep the reference > to the generic binding where this is defined (Stephen Boyd) > - Add description to clock names (Stephen Boyd) > - Correct the indendation (Stephen Boyd) > - Drop the label for display dt nodes and correct the node > name (Stephen Boyd) > > Changes in v2: > - Drop maxItems for clock (Stephen Boyd) > - Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream > dt file (Stephen Boyd) > - Keep child node directly under soc node (Stephen Boyd) > - Drop qcom,sync-dual-dsi as it is not used in upstream dt > > Changes in v3: > - Add description for register property (Stephen Boyd) > > Changes in v4: > - Add maxItems for phys property (Stephen Boyd) > - Add maxItems for reg property (Stephen Boyd) > - Add reference for data-lanes property (Stephen Boyd) > - Remove soc from example (Stephen Boyd) > > Changes in v5: > - Modify title and description (Stephen Boyd) > - Add required properties for ports node (Stephen Boyd) > - Add data-lanes in the example (Stephen Boyd) > - Drop qcom,master-dsi property (Stephen Boyd) > > Changes in v6: > - Add required properties for port@0, port@1 and corresponding > endpoints (Stephen Boyd) > - Add address-cells and size-cells for ports (Stephen Boyd) > - Use additionalProperties instead of unevaluatedProperties (Stephen Boyd) > > Changes in v7: > - Add reference for ports and data-lanes (Rob Herring) > - Add maxItems and minItems for data-lanes (Rob Herring) > --- > .../bindings/display/msm/dsi-controller-main.yaml | 209 +++++++++++++++++ > .../devicetree/bindings/display/msm/dsi.txt | 249 --------------------- > 2 files changed, 209 insertions(+), 249 deletions(-) > create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml > delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt > > diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml > new file mode 100644 > index 0000000..80f5218 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml > @@ -0,0 +1,209 @@ > +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/display/msm/dsi-controller-main.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm Display DSI controller > + > +maintainers: > + - Krishna Manikandan <mkrishn@codeaurora.org> > + > +allOf: > + - $ref: "../dsi-controller.yaml#" > + > +properties: > + compatible: > + items: > + - const: qcom,mdss-dsi-ctrl > + > + reg: > + maxItems: 1 > + > + reg-names: > + const: dsi_ctrl > + > + interrupts: > + maxItems: 1 > + > + clocks: > + items: > + - description: Display byte clock > + - description: Display byte interface clock > + - description: Display pixel clock > + - description: Display escape clock > + - description: Display AHB clock > + - description: Display AXI clock > + > + clock-names: > + items: > + - const: byte > + - const: byte_intf > + - const: pixel > + - const: core > + - const: iface > + - const: bus > + > + phys: > + maxItems: 1 > + > + phy-names: > + const: dsi > + > + "#address-cells": true > + > + "#size-cells": true > + > + syscon-sfpb: > + description: A phandle to mmss_sfpb syscon node (only for DSIv2). > + $ref: "/schemas/types.yaml#/definitions/phandle" > + > + qcom,dual-dsi-mode: > + type: boolean > + description: | > + Indicates if the DSI controller is driving a panel which needs > + 2 DSI links. > + > + power-domains: > + maxItems: 1 > + > + operating-points-v2: true > + > + ports: > + $ref: "/schemas/graph.yaml#/properties/ports" > + description: | > + Contains DSI controller input and output ports as children, each > + containing one endpoint subnode. > + > + properties: > + port@0: > + $ref: "/schemas/graph.yaml#/properties/port" > + description: | > + Input endpoints of the controller. > + > + properties: > + reg: > + const: 0 You can drop 'reg'. > + > + endpoint: > + type: object > + properties: > + remote-endpoint: true Don't need this. > + data-lanes: > + $ref: "../../media/video-interfaces.yaml" This is not where the $ref goes. Please look at other users. > + description: | > + This describes how the physical DSI data lanes are mapped > + to the logical lanes on the given platform. The value contained in > + index n describes what physical lane is mapped to the logical lane n > + (DATAn, where n lies between 0 and 3). The clock lane position is fixed > + and can't be changed. Hence, they aren't a part of the DT bindings. Don't redescribe common properties. If you have something special about this device, then say it. > + maxItems: 4 > + minItems: 4 > + items: > + enum: [ 0, 1, 2, 3 ] > + > + required: > + - reg > + - endpoint Drop. Already covered by the common schema. > + > + port@1: > + $ref: "/schemas/graph.yaml#/properties/port" > + description: | > + Output endpoints of the controller. > + properties: > + reg: > + const: 1 > + > + endpoint: > + type: object Needs a $ref to video-interfaces.yaml. > + properties: > + remote-endpoint: true > + data-lanes: > + maxItems: 4 > + minItems: 4 > + items: > + enum: [ 0, 1, 2, 3 ] > + > + required: > + - reg > + - endpoint Drop > + > + required: > + - port@0 > + - port@1 > + - "#address-cells" > + - "#size-cells" Last 2 are covered by the common schema. > + > +required: > + - compatible > + - reg > + - reg-names > + - interrupts > + - clocks > + - clock-names > + - phys > + - phy-names > + - power-domains > + - operating-points-v2 > + - ports > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/clock/qcom,dispcc-sdm845.h> > + #include <dt-bindings/clock/qcom,gcc-sdm845.h> > + #include <dt-bindings/power/qcom-rpmpd.h> > + > + dsi@ae94000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0x0ae94000 0x400>; > + reg-names = "dsi_ctrl"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + interrupt-parent = <&mdss>; > + interrupts = <4>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, > + <&dispcc DISP_CC_MDSS_ESC0_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&dispcc DISP_CC_MDSS_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + phys = <&dsi0_phy>; > + phy-names = "dsi"; > + > + power-domains = <&rpmhpd SC7180_CX>; > + operating-points-v2 = <&dsi_opp_table>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi0_in: endpoint { > + remote-endpoint = <&dpu_intf1_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi0_out: endpoint { > + remote-endpoint = <&sn65dsi86_in>; > + data-lanes = <0 1 2 3>; > + }; > + }; > + }; > + }; > +... > diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt > deleted file mode 100644 > index b9a64d3..0000000 > --- a/Documentation/devicetree/bindings/display/msm/dsi.txt > +++ /dev/null > @@ -1,249 +0,0 @@ > -Qualcomm Technologies Inc. adreno/snapdragon DSI output > - > -DSI Controller: > -Required properties: > -- compatible: > - * "qcom,mdss-dsi-ctrl" > -- reg: Physical base address and length of the registers of controller > -- reg-names: The names of register regions. The following regions are required: > - * "dsi_ctrl" > -- interrupts: The interrupt signal from the DSI block. > -- power-domains: Should be <&mmcc MDSS_GDSC>. > -- clocks: Phandles to device clocks. > -- clock-names: the following clocks are required: > - * "mdp_core" > - * "iface" > - * "bus" > - * "core_mmss" > - * "byte" > - * "pixel" > - * "core" > - For DSIv2, we need an additional clock: > - * "src" > - For DSI6G v2.0 onwards, we need also need the clock: > - * "byte_intf" > -- assigned-clocks: Parents of "byte" and "pixel" for the given platform. > -- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided > - by a DSI PHY block. See [1] for details on clock bindings. > -- vdd-supply: phandle to vdd regulator device node > -- vddio-supply: phandle to vdd-io regulator device node > -- vdda-supply: phandle to vdda regulator device node > -- phys: phandle to DSI PHY device node > -- phy-names: the name of the corresponding PHY device > -- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) > -- ports: Contains 2 DSI controller ports as child nodes. Each port contains > - an endpoint subnode as defined in [2] and [3]. > - > -Optional properties: > -- panel@0: Node of panel connected to this DSI controller. > - See files in [4] for each supported panel. > -- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is > - driving a panel which needs 2 DSI links. > -- qcom,master-dsi: Boolean value indicating if the DSI controller is driving > - the master link of the 2-DSI panel. > -- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is > - driving a 2-DSI panel whose 2 links need receive command simultaneously. > -- pinctrl-names: the pin control state names; should contain "default" > -- pinctrl-0: the default pinctrl state (active) > -- pinctrl-n: the "sleep" pinctrl state > -- ports: contains DSI controller input and output ports as children, each > - containing one endpoint subnode. > - > - DSI Endpoint properties: > - - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's > - input endpoint. For port@1, set to the MDP interface output. See [2] for > - device graph info. > - > - - data-lanes: this describes how the physical DSI data lanes are mapped > - to the logical lanes on the given platform. The value contained in > - index n describes what physical lane is mapped to the logical lane n > - (DATAn, where n lies between 0 and 3). The clock lane position is fixed > - and can't be changed. Hence, they aren't a part of the DT bindings. See > - [3] for more info on the data-lanes property. > - > - For example: > - > - data-lanes = <3 0 1 2>; > - > - The above mapping describes that the logical data lane DATA0 is mapped to > - the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 > - to phys DATA1 and logic DATA3 to phys DATA2. > - > - There are only a limited number of physical to logical mappings possible: > - <0 1 2 3> > - <1 2 3 0> > - <2 3 0 1> > - <3 0 1 2> > - <0 3 2 1> > - <1 0 3 2> > - <2 1 0 3> > - <3 2 1 0> > - > -DSI PHY: > -Required properties: > -- compatible: Could be the following > - * "qcom,dsi-phy-28nm-hpm" > - * "qcom,dsi-phy-28nm-lp" > - * "qcom,dsi-phy-20nm" > - * "qcom,dsi-phy-28nm-8960" > - * "qcom,dsi-phy-14nm" > - * "qcom,dsi-phy-14nm-660" > - * "qcom,dsi-phy-10nm" > - * "qcom,dsi-phy-10nm-8998" > - * "qcom,dsi-phy-7nm" > - * "qcom,dsi-phy-7nm-8150" > -- reg: Physical base address and length of the registers of PLL, PHY. Some > - revisions require the PHY regulator base address, whereas others require the > - PHY lane base address. See below for each PHY revision. > -- reg-names: The names of register regions. The following regions are required: > - For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY: > - * "dsi_pll" > - * "dsi_phy" > - * "dsi_phy_regulator" > - For DSI 14nm, 10nm and 7nm PHYs: > - * "dsi_pll" > - * "dsi_phy" > - * "dsi_phy_lane" > -- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating > - 2 clocks: A byte clock (index 0), and a pixel clock (index 1). > -- power-domains: Should be <&mmcc MDSS_GDSC>. > -- clocks: Phandles to device clocks. See [1] for details on clock bindings. > -- clock-names: the following clocks are required: > - * "iface" > - * "ref" (only required for new DTS files/entries) > - For 28nm HPM/LP, 28nm 8960 PHYs: > -- vddio-supply: phandle to vdd-io regulator device node > - For 20nm PHY: > -- vddio-supply: phandle to vdd-io regulator device node > -- vcca-supply: phandle to vcca regulator device node > - For 14nm PHY: > -- vcca-supply: phandle to vcca regulator device node > - For 10nm and 7nm PHY: > -- vdds-supply: phandle to vdds regulator device node > - > -Optional properties: > -- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY > - regulator is wanted. > -- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode > - panels in microseconds. Driver uses this number to adjust > - the clock rate according to the expected transfer time. > - Increasing this value would slow down the mdp processing > - and can result in slower performance. > - Decreasing this value can speed up the mdp processing, > - but this can also impact power consumption. > - As a rule this time should not be higher than the time > - that would be expected with the processing at the > - dsi link rate since anyways this would be the maximum > - transfer time that could be achieved. > - If ping pong split is enabled, this time should not be higher > - than two times the dsi link rate time. > - If the property is not specified, then the default value is 14000 us. > - > -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt > -[2] Documentation/devicetree/bindings/graph.txt > -[3] Documentation/devicetree/bindings/media/video-interfaces.txt > -[4] Documentation/devicetree/bindings/display/panel/ > - > -Example: > - dsi0: dsi@fd922800 { > - compatible = "qcom,mdss-dsi-ctrl"; > - qcom,dsi-host-index = <0>; > - interrupt-parent = <&mdp>; > - interrupts = <4 0>; > - reg-names = "dsi_ctrl"; > - reg = <0xfd922800 0x200>; > - power-domains = <&mmcc MDSS_GDSC>; > - clock-names = > - "bus", > - "byte", > - "core", > - "core_mmss", > - "iface", > - "mdp_core", > - "pixel"; > - clocks = > - <&mmcc MDSS_AXI_CLK>, > - <&mmcc MDSS_BYTE0_CLK>, > - <&mmcc MDSS_ESC0_CLK>, > - <&mmcc MMSS_MISC_AHB_CLK>, > - <&mmcc MDSS_AHB_CLK>, > - <&mmcc MDSS_MDP_CLK>, > - <&mmcc MDSS_PCLK0_CLK>; > - > - assigned-clocks = > - <&mmcc BYTE0_CLK_SRC>, > - <&mmcc PCLK0_CLK_SRC>; > - assigned-clock-parents = > - <&dsi_phy0 0>, > - <&dsi_phy0 1>; > - > - vdda-supply = <&pma8084_l2>; > - vdd-supply = <&pma8084_l22>; > - vddio-supply = <&pma8084_l12>; > - > - phys = <&dsi_phy0>; > - phy-names ="dsi-phy"; > - > - qcom,dual-dsi-mode; > - qcom,master-dsi; > - qcom,sync-dual-dsi; > - > - qcom,mdss-mdp-transfer-time-us = <12000>; > - > - pinctrl-names = "default", "sleep"; > - pinctrl-0 = <&dsi_active>; > - pinctrl-1 = <&dsi_suspend>; > - > - ports { > - #address-cells = <1>; > - #size-cells = <0>; > - > - port@0 { > - reg = <0>; > - dsi0_in: endpoint { > - remote-endpoint = <&mdp_intf1_out>; > - }; > - }; > - > - port@1 { > - reg = <1>; > - dsi0_out: endpoint { > - remote-endpoint = <&panel_in>; > - data-lanes = <0 1 2 3>; > - }; > - }; > - }; > - > - panel: panel@0 { > - compatible = "sharp,lq101r1sx01"; > - reg = <0>; > - link2 = <&secondary>; > - > - power-supply = <...>; > - backlight = <...>; > - > - port { > - panel_in: endpoint { > - remote-endpoint = <&dsi0_out>; > - }; > - }; > - }; > - }; > - > - dsi_phy0: dsi-phy@fd922a00 { > - compatible = "qcom,dsi-phy-28nm-hpm"; > - qcom,dsi-phy-index = <0>; > - reg-names = > - "dsi_pll", > - "dsi_phy", > - "dsi_phy_regulator"; > - reg = <0xfd922a00 0xd4>, > - <0xfd922b00 0x2b0>, > - <0xfd922d80 0x7b>; > - clock-names = "iface"; > - clocks = <&mmcc MDSS_AHB_CLK>; > - #clock-cells = <1>; > - vddio-supply = <&pma8084_l12>; > - > - qcom,dsi-phy-regulator-ldo-mode; > - }; > -- > 2.7.4 >
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml new file mode 100644 index 0000000..80f5218 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml @@ -0,0 +1,209 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dsi-controller-main.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Display DSI controller + +maintainers: + - Krishna Manikandan <mkrishn@codeaurora.org> + +allOf: + - $ref: "../dsi-controller.yaml#" + +properties: + compatible: + items: + - const: qcom,mdss-dsi-ctrl + + reg: + maxItems: 1 + + reg-names: + const: dsi_ctrl + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Display byte clock + - description: Display byte interface clock + - description: Display pixel clock + - description: Display escape clock + - description: Display AHB clock + - description: Display AXI clock + + clock-names: + items: + - const: byte + - const: byte_intf + - const: pixel + - const: core + - const: iface + - const: bus + + phys: + maxItems: 1 + + phy-names: + const: dsi + + "#address-cells": true + + "#size-cells": true + + syscon-sfpb: + description: A phandle to mmss_sfpb syscon node (only for DSIv2). + $ref: "/schemas/types.yaml#/definitions/phandle" + + qcom,dual-dsi-mode: + type: boolean + description: | + Indicates if the DSI controller is driving a panel which needs + 2 DSI links. + + power-domains: + maxItems: 1 + + operating-points-v2: true + + ports: + $ref: "/schemas/graph.yaml#/properties/ports" + description: | + Contains DSI controller input and output ports as children, each + containing one endpoint subnode. + + properties: + port@0: + $ref: "/schemas/graph.yaml#/properties/port" + description: | + Input endpoints of the controller. + + properties: + reg: + const: 0 + + endpoint: + type: object + properties: + remote-endpoint: true + data-lanes: + $ref: "../../media/video-interfaces.yaml" + description: | + This describes how the physical DSI data lanes are mapped + to the logical lanes on the given platform. The value contained in + index n describes what physical lane is mapped to the logical lane n + (DATAn, where n lies between 0 and 3). The clock lane position is fixed + and can't be changed. Hence, they aren't a part of the DT bindings. + maxItems: 4 + minItems: 4 + items: + enum: [ 0, 1, 2, 3 ] + + required: + - reg + - endpoint + + port@1: + $ref: "/schemas/graph.yaml#/properties/port" + description: | + Output endpoints of the controller. + properties: + reg: + const: 1 + + endpoint: + type: object + properties: + remote-endpoint: true + data-lanes: + maxItems: 4 + minItems: 4 + items: + enum: [ 0, 1, 2, 3 ] + + required: + - reg + - endpoint + + required: + - port@0 + - port@1 + - "#address-cells" + - "#size-cells" + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + - clock-names + - phys + - phy-names + - power-domains + - operating-points-v2 + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,dispcc-sdm845.h> + #include <dt-bindings/clock/qcom,gcc-sdm845.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + dsi@ae94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0x0ae94000 0x400>; + reg-names = "dsi_ctrl"; + + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&mdss>; + interrupts = <4>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + phys = <&dsi0_phy>; + phy-names = "dsi"; + + power-domains = <&rpmhpd SC7180_CX>; + operating-points-v2 = <&dsi_opp_table>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&dpu_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + remote-endpoint = <&sn65dsi86_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt deleted file mode 100644 index b9a64d3..0000000 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ /dev/null @@ -1,249 +0,0 @@ -Qualcomm Technologies Inc. adreno/snapdragon DSI output - -DSI Controller: -Required properties: -- compatible: - * "qcom,mdss-dsi-ctrl" -- reg: Physical base address and length of the registers of controller -- reg-names: The names of register regions. The following regions are required: - * "dsi_ctrl" -- interrupts: The interrupt signal from the DSI block. -- power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: Phandles to device clocks. -- clock-names: the following clocks are required: - * "mdp_core" - * "iface" - * "bus" - * "core_mmss" - * "byte" - * "pixel" - * "core" - For DSIv2, we need an additional clock: - * "src" - For DSI6G v2.0 onwards, we need also need the clock: - * "byte_intf" -- assigned-clocks: Parents of "byte" and "pixel" for the given platform. -- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided - by a DSI PHY block. See [1] for details on clock bindings. -- vdd-supply: phandle to vdd regulator device node -- vddio-supply: phandle to vdd-io regulator device node -- vdda-supply: phandle to vdda regulator device node -- phys: phandle to DSI PHY device node -- phy-names: the name of the corresponding PHY device -- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) -- ports: Contains 2 DSI controller ports as child nodes. Each port contains - an endpoint subnode as defined in [2] and [3]. - -Optional properties: -- panel@0: Node of panel connected to this DSI controller. - See files in [4] for each supported panel. -- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is - driving a panel which needs 2 DSI links. -- qcom,master-dsi: Boolean value indicating if the DSI controller is driving - the master link of the 2-DSI panel. -- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is - driving a 2-DSI panel whose 2 links need receive command simultaneously. -- pinctrl-names: the pin control state names; should contain "default" -- pinctrl-0: the default pinctrl state (active) -- pinctrl-n: the "sleep" pinctrl state -- ports: contains DSI controller input and output ports as children, each - containing one endpoint subnode. - - DSI Endpoint properties: - - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's - input endpoint. For port@1, set to the MDP interface output. See [2] for - device graph info. - - - data-lanes: this describes how the physical DSI data lanes are mapped - to the logical lanes on the given platform. The value contained in - index n describes what physical lane is mapped to the logical lane n - (DATAn, where n lies between 0 and 3). The clock lane position is fixed - and can't be changed. Hence, they aren't a part of the DT bindings. See - [3] for more info on the data-lanes property. - - For example: - - data-lanes = <3 0 1 2>; - - The above mapping describes that the logical data lane DATA0 is mapped to - the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 - to phys DATA1 and logic DATA3 to phys DATA2. - - There are only a limited number of physical to logical mappings possible: - <0 1 2 3> - <1 2 3 0> - <2 3 0 1> - <3 0 1 2> - <0 3 2 1> - <1 0 3 2> - <2 1 0 3> - <3 2 1 0> - -DSI PHY: -Required properties: -- compatible: Could be the following - * "qcom,dsi-phy-28nm-hpm" - * "qcom,dsi-phy-28nm-lp" - * "qcom,dsi-phy-20nm" - * "qcom,dsi-phy-28nm-8960" - * "qcom,dsi-phy-14nm" - * "qcom,dsi-phy-14nm-660" - * "qcom,dsi-phy-10nm" - * "qcom,dsi-phy-10nm-8998" - * "qcom,dsi-phy-7nm" - * "qcom,dsi-phy-7nm-8150" -- reg: Physical base address and length of the registers of PLL, PHY. Some - revisions require the PHY regulator base address, whereas others require the - PHY lane base address. See below for each PHY revision. -- reg-names: The names of register regions. The following regions are required: - For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY: - * "dsi_pll" - * "dsi_phy" - * "dsi_phy_regulator" - For DSI 14nm, 10nm and 7nm PHYs: - * "dsi_pll" - * "dsi_phy" - * "dsi_phy_lane" -- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating - 2 clocks: A byte clock (index 0), and a pixel clock (index 1). -- power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: Phandles to device clocks. See [1] for details on clock bindings. -- clock-names: the following clocks are required: - * "iface" - * "ref" (only required for new DTS files/entries) - For 28nm HPM/LP, 28nm 8960 PHYs: -- vddio-supply: phandle to vdd-io regulator device node - For 20nm PHY: -- vddio-supply: phandle to vdd-io regulator device node -- vcca-supply: phandle to vcca regulator device node - For 14nm PHY: -- vcca-supply: phandle to vcca regulator device node - For 10nm and 7nm PHY: -- vdds-supply: phandle to vdds regulator device node - -Optional properties: -- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY - regulator is wanted. -- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode - panels in microseconds. Driver uses this number to adjust - the clock rate according to the expected transfer time. - Increasing this value would slow down the mdp processing - and can result in slower performance. - Decreasing this value can speed up the mdp processing, - but this can also impact power consumption. - As a rule this time should not be higher than the time - that would be expected with the processing at the - dsi link rate since anyways this would be the maximum - transfer time that could be achieved. - If ping pong split is enabled, this time should not be higher - than two times the dsi link rate time. - If the property is not specified, then the default value is 14000 us. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/graph.txt -[3] Documentation/devicetree/bindings/media/video-interfaces.txt -[4] Documentation/devicetree/bindings/display/panel/ - -Example: - dsi0: dsi@fd922800 { - compatible = "qcom,mdss-dsi-ctrl"; - qcom,dsi-host-index = <0>; - interrupt-parent = <&mdp>; - interrupts = <4 0>; - reg-names = "dsi_ctrl"; - reg = <0xfd922800 0x200>; - power-domains = <&mmcc MDSS_GDSC>; - clock-names = - "bus", - "byte", - "core", - "core_mmss", - "iface", - "mdp_core", - "pixel"; - clocks = - <&mmcc MDSS_AXI_CLK>, - <&mmcc MDSS_BYTE0_CLK>, - <&mmcc MDSS_ESC0_CLK>, - <&mmcc MMSS_MISC_AHB_CLK>, - <&mmcc MDSS_AHB_CLK>, - <&mmcc MDSS_MDP_CLK>, - <&mmcc MDSS_PCLK0_CLK>; - - assigned-clocks = - <&mmcc BYTE0_CLK_SRC>, - <&mmcc PCLK0_CLK_SRC>; - assigned-clock-parents = - <&dsi_phy0 0>, - <&dsi_phy0 1>; - - vdda-supply = <&pma8084_l2>; - vdd-supply = <&pma8084_l22>; - vddio-supply = <&pma8084_l12>; - - phys = <&dsi_phy0>; - phy-names ="dsi-phy"; - - qcom,dual-dsi-mode; - qcom,master-dsi; - qcom,sync-dual-dsi; - - qcom,mdss-mdp-transfer-time-us = <12000>; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&dsi_active>; - pinctrl-1 = <&dsi_suspend>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - dsi0_in: endpoint { - remote-endpoint = <&mdp_intf1_out>; - }; - }; - - port@1 { - reg = <1>; - dsi0_out: endpoint { - remote-endpoint = <&panel_in>; - data-lanes = <0 1 2 3>; - }; - }; - }; - - panel: panel@0 { - compatible = "sharp,lq101r1sx01"; - reg = <0>; - link2 = <&secondary>; - - power-supply = <...>; - backlight = <...>; - - port { - panel_in: endpoint { - remote-endpoint = <&dsi0_out>; - }; - }; - }; - }; - - dsi_phy0: dsi-phy@fd922a00 { - compatible = "qcom,dsi-phy-28nm-hpm"; - qcom,dsi-phy-index = <0>; - reg-names = - "dsi_pll", - "dsi_phy", - "dsi_phy_regulator"; - reg = <0xfd922a00 0xd4>, - <0xfd922b00 0x2b0>, - <0xfd922d80 0x7b>; - clock-names = "iface"; - clocks = <&mmcc MDSS_AHB_CLK>; - #clock-cells = <1>; - vddio-supply = <&pma8084_l12>; - - qcom,dsi-phy-regulator-ldo-mode; - };
Add YAML schema for the device tree bindings for DSI Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org> Changes in v1: - Separate dsi controller bindings to a separate patch (Stephen Boyd) - Merge dsi-common-controller.yaml and dsi-controller-main.yaml to a single file (Stephen Boyd) - Drop supply entries and definitions from properties (Stephen Boyd) - Modify phy-names property for dsi controller (Stephen Boyd) - Remove boolean from description (Stephen Boyd) - Drop pinctrl properties as they are standard entries (Stephen Boyd) - Modify the description for ports property and keep the reference to the generic binding where this is defined (Stephen Boyd) - Add description to clock names (Stephen Boyd) - Correct the indendation (Stephen Boyd) - Drop the label for display dt nodes and correct the node name (Stephen Boyd) Changes in v2: - Drop maxItems for clock (Stephen Boyd) - Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream dt file (Stephen Boyd) - Keep child node directly under soc node (Stephen Boyd) - Drop qcom,sync-dual-dsi as it is not used in upstream dt Changes in v3: - Add description for register property (Stephen Boyd) Changes in v4: - Add maxItems for phys property (Stephen Boyd) - Add maxItems for reg property (Stephen Boyd) - Add reference for data-lanes property (Stephen Boyd) - Remove soc from example (Stephen Boyd) Changes in v5: - Modify title and description (Stephen Boyd) - Add required properties for ports node (Stephen Boyd) - Add data-lanes in the example (Stephen Boyd) - Drop qcom,master-dsi property (Stephen Boyd) Changes in v6: - Add required properties for port@0, port@1 and corresponding endpoints (Stephen Boyd) - Add address-cells and size-cells for ports (Stephen Boyd) - Use additionalProperties instead of unevaluatedProperties (Stephen Boyd) Changes in v7: - Add reference for ports and data-lanes (Rob Herring) - Add maxItems and minItems for data-lanes (Rob Herring) --- .../bindings/display/msm/dsi-controller-main.yaml | 209 +++++++++++++++++ .../devicetree/bindings/display/msm/dsi.txt | 249 --------------------- 2 files changed, 209 insertions(+), 249 deletions(-) create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt