@@ -63,6 +63,22 @@
};
};
+ /*
+ * These channels from the ADC are simply hardware monitors.
+ * That is why the ADC is referred to as "HKADC" - HouseKeeping
+ * ADC.
+ */
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&xoadc 0x00 0x01>, /* Battery */
+ <&xoadc 0x00 0x01>, /* DC in (charger) */
+ <&xoadc 0x00 0x04>, /* VPH the main system voltage */
+ <&xoadc 0x00 0x0b>, /* Die temperature */
+ <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+ <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+ <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -267,6 +283,49 @@
row-hold = <91500>;
};
+ xoadc: xoadc@197 {
+ compatible = "qcom,pm8058-adc";
+ reg = <0x197>;
+ interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #io-channel-cells = <2>;
+
+ vcoin: adc-channel@00 {
+ reg = <0x00 0x00>;
+ };
+ vbat: adc-channel@01 {
+ reg = <0x00 0x01>;
+ };
+ dcin: adc-channel@02 {
+ reg = <0x00 0x02>;
+ };
+ ichg: adc-channel@30 {
+ reg = <0x00 0x03>;
+ };
+ vph_pwr: adc-channel@04 {
+ reg = <0x00 0x04>;
+ };
+ usb_vbus: adc-channel@0a {
+ reg = <0x00 0x0a>;
+ };
+ die_temp: adc-channel@0b {
+ reg = <0x00 0x0b>;
+ };
+ ref_625mv: adc-channel@0c {
+ reg = <0x00 0x0c>;
+ };
+ ref_1250mv: adc-channel@0d {
+ reg = <0x00 0x0d>;
+ };
+ ref_325mv: adc-channel@0e {
+ reg = <0x00 0x0e>;
+ };
+ ref_muxoff: adc-channel@0f {
+ reg = <0x00 0x0f>;
+ };
+ };
+
rtc@1e8 {
compatible = "qcom,pm8058-rtc";
reg = <0x1e8>;
This adds the PM8058 XOADC node to the PM8058 PMIC node, defines the 16 channels and further also define an IIO HWMON node for the channels that are used for housekeeping of voltages and die temperature for the PMIC chip die. Tested on the APQ8060 DragonBoard: cd /sys/class/hwmon/hwmon0 cat in2_input 4773 (DC mains ~5V) cat in4_input 625 (0.625V reference voltage) cat in5_input 1250 (1.25V reference voltage) cat temp1_input 35852 (die temperature) Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v5: - Switch to the twocell addressing scheme specified in the new bindings. - The bindings and IIO driver are both queued for v4.12 in the IIO tree and pending in linux-next --- arch/arm/boot/dts/qcom-msm8660.dtsi | 59 +++++++++++++++++++++++++++++++++++++ 1 file changed, 59 insertions(+)