@@ -36,4 +36,30 @@
drive-strength = <2>; /* 2 MA */
};
};
+
+ blsp1_uart1_default: blsp1_uart1_default {
+ mux {
+ pins = "gpio41", "gpio42", "gpio43", "gpio44";
+ function = "blsp_uart2";
+ };
+
+ config {
+ pins = "gpio41", "gpio42", "gpio43", "gpio44";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ blsp1_uart1_sleep: blsp1_uart1_sleep {
+ mux {
+ pins = "gpio41", "gpio42", "gpio43", "gpio44";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio41", "gpio42", "gpio43", "gpio44";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
};
@@ -26,6 +26,27 @@
};
};
+ divclk4_pin_a: divclk4 {
+ pinconf {
+ pins = "gpio18";
+ function = PMIC_GPIO_FUNC_FUNC2;
+
+ bias-disable;
+ power-source = <PM8994_GPIO_S4>;
+ };
+ };
+
+ bt_en_pin_a: bt-en-active {
+ pinconf {
+ pins = "gpio19";
+ function = PMIC_GPIO_FUNC_NORMAL;
+
+ output-low;
+ power-source = <PM8994_GPIO_S4>; // 1.8V
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ };
+ };
+
usb3_vbus_det_gpio: pm8996_gpio22 {
pinconf {
pins = "gpio22";
@@ -23,6 +23,7 @@
aliases {
serial0 = &blsp2_uart1;
serial1 = &blsp2_uart2;
+ serial2 = &blsp1_uart1;
i2c0 = &blsp1_i2c2;
i2c1 = &blsp2_i2c1;
i2c2 = &blsp2_i2c0;
@@ -34,7 +35,39 @@
stdout-path = "serial0:115200n8";
};
+ clocks {
+ divclk4: divclk4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "divclk4";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&divclk4_pin_a>;
+ };
+ };
+
soc {
+ serial@7570000 {
+ label = "BT-UART";
+ status = "okay";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart1_default>;
+ pinctrl-1 = <&blsp1_uart1_sleep>;
+
+ bluetooth {
+ compatible = "qcom,qca6174-bt";
+
+ /* bt_disable_n gpio */
+ enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_en_pin_a>;
+
+ clocks = <&divclk4>;
+ };
+ };
+
serial@75b0000 {
label = "LS-UART1";
status = "okay";
@@ -408,6 +408,16 @@
#clock-cells = <1>;
};
+ blsp1_uart1: serial@7570000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x07570000 0x1000>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
blsp1_spi0: spi@7575000 {
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x07575000 0x600>;
Add a new serial node for the Qualcomm BT controller QCA6174. This allows automatic probing and hci registration through the serdev framework instead of relying on the userspace helpers. Signed-off-by: Thierry Escande <thierry.escande@linaro.org> --- v6 - Move gpio properties into pinconf subnode - move pinmux properties into mux and config subnodes v5: - Rename 'bt-disable-n' gpio as 'enable' v4: no change v3: no change v2: - Fix author email arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi | 26 +++++++++++++++++ .../boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi | 21 ++++++++++++++ arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 33 ++++++++++++++++++++++ arch/arm64/boot/dts/qcom/msm8996.dtsi | 10 +++++++ 4 files changed, 90 insertions(+)