[v3,1/2] dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY

Commit Message

Bjorn Andersson May 2, 2019, 12:14 a.m. UTC

The Qualcomm PCIe2 PHY is a Synopsys based PCIe PHY found in a number of
Qualcomm platforms, add a binding to describe this.

Signed-off-by: Bjorn Andersson <[e-mail]>
---

Changes since v2:
- Add #clock-cells

 .../bindings/phy/qcom-pcie2-phy.txt           | 42 +++++++++++++++++++
 1 file changed, 42 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt

Comments

Rob Herring May 2, 2019, 9:36 p.m. UTC | #1

On Wed,  1 May 2019 17:14:05 -0700, Bjorn Andersson wrote:
> The Qualcomm PCIe2 PHY is a Synopsys based PCIe PHY found in a number of
> Qualcomm platforms, add a binding to describe this.
> 
> Signed-off-by: Bjorn Andersson <[e-mail]>
> ---
> 
> Changes since v2:
> - Add #clock-cells
> 
>  .../bindings/phy/qcom-pcie2-phy.txt           | 42 +++++++++++++++++++
>  1 file changed, 42 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
> 

Reviewed-by: Rob Herring <[e-mail]>

Patch

diff --git a/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
new file mode 100644
index 000000000000..30064253f290
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
@@ -0,0 +1,42 @@ 
+Qualcomm PCIe2 PHY controller
+=============================
+
+The Qualcomm PCIe2 PHY is a Synopsys based phy found in a number of Qualcomm
+platforms.
+
+Required properties:
+ - compatible: compatible list, should be:
+	       "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy"
+
+ - reg: offset and length of the PHY register set.
+ - #phy-cells: must be 0.
+
+ - clocks: a clock-specifier pair for the "pipe" clock
+
+ - vdda-vp-supply: phandle to low voltage regulator
+ - vdda-vph-supply: phandle to high voltage regulator
+
+ - resets: reset-specifier pairs for the "phy" and "pipe" resets
+ - reset-names: list of resets, should contain:
+		"phy" and "pipe"
+
+ - clock-output-names: name of the outgoing clock signal from the PHY PLL
+ - #clock-cells: must be 0
+
+Example:
+ phy@7786000 {
+	compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
+	reg = <0x07786000 0xb8>;
+
+	clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+	resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
+	         <&gcc GCC_PCIE_0_PIPE_ARES>;
+	reset-names = "phy", "pipe";
+
+	vdda-vp-supply = <&vreg_l3_1p05>;
+	vdda-vph-supply = <&vreg_l5_1p8>;
+
+	clock-output-names = "pcie_0_pipe_clk";
+	#clock-cells = <0>;
+	#phy-cells = <0>;
+ };