@@ -142,6 +142,10 @@
status = "okay";
};
+&camss {
+ vdda-supply = <&pm8994_l2>;
+};
+
&sdhc2 {
/* External SD card */
pinctrl-names = "default", "sleep";
@@ -155,10 +159,28 @@
&ufsphy {
status = "okay";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+
+ vdda-phy-max-microamp = <18380>;
+ vdda-pll-max-microamp = <9440>;
+
+ vddp-ref-clk-supply = <&pm8994_l25>;
+ vddp-ref-clk-max-microamp = <100>;
+ vddp-ref-clk-always-on;
};
&ufshc {
status = "okay";
+
+ vcc-supply = <&pm8994_l20>;
+ vccq-supply = <&pm8994_l25>;
+ vccq2-supply = <&pm8994_s4>;
+
+ vcc-max-microamp = <600000>;
+ vccq-max-microamp = <450000>;
+ vccq2-max-microamp = <450000>;
};
&msmgpio {
@@ -369,18 +391,31 @@
&pcie_phy {
status = "okay";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
};
&usb3phy {
status = "okay";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+
};
&hsusb_phy1 {
status = "okay";
+
+ vdda-pll-supply = <&pm8994_l12>;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
};
&hsusb_phy2 {
status = "okay";
+
+ vdda-pll-supply = <&pm8994_l12>;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
};
&usb3 {
@@ -408,22 +443,31 @@
status = "okay";
perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
vddpe-3v3-supply = <&wlan_en>;
+ vdda-supply = <&pm8994_l28>;
};
&pcie1 {
status = "okay";
perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
+ vdda-supply = <&pm8994_l28>;
};
&pcie2 {
status = "okay";
perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
+ vdda-supply = <&pm8994_l28>;
};
&wcd9335 {
clock-names = "mclk", "slimbus";
clocks = <&div1_mclk>,
<&rpmcc RPM_SMD_BB_CLK1>;
+
+ vdd-buck-supply = <&pm8994_s4>;
+ vdd-buck-sido-supply = <&pm8994_s4>;
+ vdd-tx-supply = <&pm8994_s4>;
+ vdd-rx-supply = <&pm8994_s4>;
+ vdd-io-supply = <&pm8994_s4>;
};
&mdss {
@@ -1322,16 +1322,6 @@
reg-names = "phy_mem";
#phy-cells = <0>;
- vdda-phy-supply = <&pm8994_l28>;
- vdda-pll-supply = <&pm8994_l12>;
-
- vdda-phy-max-microamp = <18380>;
- vdda-pll-max-microamp = <9440>;
-
- vddp-ref-clk-supply = <&pm8994_l25>;
- vddp-ref-clk-max-microamp = <100>;
- vddp-ref-clk-always-on;
-
clock-names = "ref_clk_src", "ref_clk";
clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
<&gcc GCC_UFS_CLKREF_CLK>;
@@ -1347,14 +1337,6 @@
phys = <&ufsphy>;
phy-names = "ufsphy";
- vcc-supply = <&pm8994_l20>;
- vccq-supply = <&pm8994_l25>;
- vccq2-supply = <&pm8994_s4>;
-
- vcc-max-microamp = <600000>;
- vccq-max-microamp = <450000>;
- vccq2-max-microamp = <450000>;
-
power-domains = <&gcc UFS_GDSC>;
clock-names =
@@ -1456,9 +1438,6 @@
<&gcc GCC_PCIE_CLKREF_CLK>;
clock-names = "aux", "cfg_ahb", "ref";
- vdda-phy-supply = <&pm8994_l28>;
- vdda-pll-supply = <&pm8994_l12>;
-
resets = <&gcc GCC_PCIE_PHY_BCR>,
<&gcc GCC_PCIE_PHY_COM_BCR>,
<&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
@@ -1518,9 +1497,6 @@
<&gcc GCC_USB3_CLKREF_CLK>;
clock-names = "aux", "cfg_ahb", "ref";
- vdda-phy-supply = <&pm8994_l28>;
- vdda-pll-supply = <&pm8994_l12>;
-
resets = <&gcc GCC_USB3_PHY_BCR>,
<&gcc GCC_USB3PHY_PHY_BCR>;
reset-names = "phy", "common";
@@ -1547,9 +1523,6 @@
<&gcc GCC_RX1_USB2_CLKREF_CLK>;
clock-names = "cfg_ahb", "ref";
- vdda-pll-supply = <&pm8994_l12>;
- vdda-phy-dpdm-supply = <&pm8994_l24>;
-
resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
nvmem-cells = <&qusb2p_hstx_trim>;
status = "disabled";
@@ -1564,9 +1537,6 @@
<&gcc GCC_RX2_USB2_CLKREF_CLK>;
clock-names = "cfg_ahb", "ref";
- vdda-pll-supply = <&pm8994_l12>;
- vdda-phy-dpdm-supply = <&pm8994_l24>;
-
resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
nvmem-cells = <&qusb2s_hstx_trim>;
status = "disabled";
@@ -1770,7 +1740,6 @@
"vfe1_stream",
"vfe_ahb",
"vfe_axi";
- vdda-supply = <&pm8994_l2>;
iommus = <&vfe_smmu 0>,
<&vfe_smmu 1>,
<&vfe_smmu 2>,
@@ -1882,9 +1851,6 @@
pinctrl-0 = <&pcie0_clkreq_default &pcie0_perst_default &pcie0_wake_default>;
pinctrl-1 = <&pcie0_clkreq_sleep &pcie0_perst_default &pcie0_wake_sleep>;
-
- vdda-supply = <&pm8994_l28>;
-
linux,pci-domain = <0>;
clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
@@ -1937,8 +1903,6 @@
pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>;
pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>;
-
- vdda-supply = <&pm8994_l28>;
linux,pci-domain = <1>;
clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
@@ -1990,8 +1954,6 @@
pinctrl-0 = <&pcie2_clkreq_default &pcie2_perst_default &pcie2_wake_default>;
pinctrl-1 = <&pcie2_clkreq_sleep &pcie2_perst_default &pcie2_wake_sleep >;
- vdda-supply = <&pm8994_l28>;
-
linux,pci-domain = <2>;
clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
<&gcc GCC_PCIE_2_AUX_CLK>,
@@ -2056,12 +2018,6 @@
slim-ifc-dev = <&tasha_ifd>;
- vdd-buck-supply = <&pm8994_s4>;
- vdd-buck-sido-supply = <&pm8994_s4>;
- vdd-tx-supply = <&pm8994_s4>;
- vdd-rx-supply = <&pm8994_s4>;
- vdd-io-supply = <&pm8994_s4>;
-
#sound-dai-cells = <1>;
};
};
Supplies for the various components in the SoC depends on board layout, so move the supply definitions to db820c.dtsi instead of carrying them in the platform dtsi. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> --- arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 44 ++++++++++++++++++++ arch/arm64/boot/dts/qcom/msm8996.dtsi | 44 -------------------- 2 files changed, 44 insertions(+), 44 deletions(-)