| Message ID | 20191021154616.25457-1-jeffrey.l.hugo@gmail.com (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | b027ce258369cbfa88401a691c23dad01deb9f9b |
| Headers | show |
| Series | [v2] tty: serial: msm_serial: Fix flow control | expand |
On Mon 21 Oct 08:46 PDT 2019, Jeffrey Hugo wrote: > hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and > Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca > disables flow, configures the uart baudrate, and then reenables flow - at > which point an event is expected to be received over the uart from the > wcn3990. It is observed that this event comes after the baudrate change > but before hci_qca re-enables flow. This is unexpected, and is a result of > msm_reset() being broken. > > According to the uart_dm hardware documentation, it is recommended that > automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto > hw flow control will manage RFR based on the configured watermark. When > there is space to receive data, the hw will assert RFR. When the watermark > is hit, the hw will de-assert RFR. > > The hardware documentation indicates that RFR can me manually managed via > CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR > de-asserts RFR. > > msm_reset() is broken because after resetting the hardware, it > unconditionally asserts RFR via SET_RFR. This enables flow regardless of > the current configuration, and would undo a previous flow disable > operation. It should instead de-assert RFR via RESET_RFR to block flow > until the hardware is reconfigured. msm_serial should rely on the client > to specify that flow should be enabled, either via mctrl() or the termios > structure, and only assert RFR in response to those triggers. > > Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") > Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Looks good! Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> > --- > > v2: > -mask out RX_RDY_CTL in msm_reset() to close a small race window for RFR > > drivers/tty/serial/msm_serial.c | 6 +++++- > 1 file changed, 5 insertions(+), 1 deletion(-) > > diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c > index 3657a24913fc..00964b6e4ac1 100644 > --- a/drivers/tty/serial/msm_serial.c > +++ b/drivers/tty/serial/msm_serial.c > @@ -980,6 +980,7 @@ static unsigned int msm_get_mctrl(struct uart_port *port) > static void msm_reset(struct uart_port *port) > { > struct msm_port *msm_port = UART_TO_MSM(port); > + unsigned int mr; > > /* reset everything */ > msm_write(port, UART_CR_CMD_RESET_RX, UART_CR); > @@ -987,7 +988,10 @@ static void msm_reset(struct uart_port *port) > msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR); > msm_write(port, UART_CR_CMD_RESET_BREAK_INT, UART_CR); > msm_write(port, UART_CR_CMD_RESET_CTS, UART_CR); > - msm_write(port, UART_CR_CMD_SET_RFR, UART_CR); > + msm_write(port, UART_CR_CMD_RESET_RFR, UART_CR); > + mr = msm_read(port, UART_MR1); > + mr &= ~UART_MR1_RX_RDY_CTL; > + msm_write(port, mr, UART_MR1); > > /* Disable DM modes */ > if (msm_port->is_uartdm) > -- > 2.17.1 >
On Mon, Oct 21, 2019 at 08:46:16AM -0700, Jeffrey Hugo wrote: > hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and > Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca > disables flow, configures the uart baudrate, and then reenables flow - at > which point an event is expected to be received over the uart from the > wcn3990. It is observed that this event comes after the baudrate change > but before hci_qca re-enables flow. This is unexpected, and is a result of > msm_reset() being broken. > > According to the uart_dm hardware documentation, it is recommended that > automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto > hw flow control will manage RFR based on the configured watermark. When > there is space to receive data, the hw will assert RFR. When the watermark > is hit, the hw will de-assert RFR. > > The hardware documentation indicates that RFR can me manually managed via > CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR > de-asserts RFR. > > msm_reset() is broken because after resetting the hardware, it > unconditionally asserts RFR via SET_RFR. This enables flow regardless of > the current configuration, and would undo a previous flow disable > operation. It should instead de-assert RFR via RESET_RFR to block flow > until the hardware is reconfigured. msm_serial should rely on the client > to specify that flow should be enabled, either via mctrl() or the termios > structure, and only assert RFR in response to those triggers. > > Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") > Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> > --- Reviewed-by: Andy Gross <agross@kernel.org> Greg, can you pick this one up? Thanks, Andy
On Sat, Oct 26, 2019 at 11:55 PM Andy Gross <agross@kernel.org> wrote: > > On Mon, Oct 21, 2019 at 08:46:16AM -0700, Jeffrey Hugo wrote: > > hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and > > Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca > > disables flow, configures the uart baudrate, and then reenables flow - at > > which point an event is expected to be received over the uart from the > > wcn3990. It is observed that this event comes after the baudrate change > > but before hci_qca re-enables flow. This is unexpected, and is a result of > > msm_reset() being broken. > > > > According to the uart_dm hardware documentation, it is recommended that > > automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto > > hw flow control will manage RFR based on the configured watermark. When > > there is space to receive data, the hw will assert RFR. When the watermark > > is hit, the hw will de-assert RFR. > > > > The hardware documentation indicates that RFR can me manually managed via > > CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR > > de-asserts RFR. > > > > msm_reset() is broken because after resetting the hardware, it > > unconditionally asserts RFR via SET_RFR. This enables flow regardless of > > the current configuration, and would undo a previous flow disable > > operation. It should instead de-assert RFR via RESET_RFR to block flow > > until the hardware is reconfigured. msm_serial should rely on the client > > to specify that flow should be enabled, either via mctrl() or the termios > > structure, and only assert RFR in response to those triggers. > > > > Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") > > Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> > > --- > > Reviewed-by: Andy Gross <agross@kernel.org> > > Greg, can you pick this one up? > > Thanks, > Andy Greg, will this be queued for 5.5?
On Sun, Nov 03, 2019 at 02:51:17PM -0700, Jeffrey Hugo wrote: > On Sat, Oct 26, 2019 at 11:55 PM Andy Gross <agross@kernel.org> wrote: > > > > On Mon, Oct 21, 2019 at 08:46:16AM -0700, Jeffrey Hugo wrote: > > > hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and > > > Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca > > > disables flow, configures the uart baudrate, and then reenables flow - at > > > which point an event is expected to be received over the uart from the > > > wcn3990. It is observed that this event comes after the baudrate change > > > but before hci_qca re-enables flow. This is unexpected, and is a result of > > > msm_reset() being broken. > > > > > > According to the uart_dm hardware documentation, it is recommended that > > > automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto > > > hw flow control will manage RFR based on the configured watermark. When > > > there is space to receive data, the hw will assert RFR. When the watermark > > > is hit, the hw will de-assert RFR. > > > > > > The hardware documentation indicates that RFR can me manually managed via > > > CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR > > > de-asserts RFR. > > > > > > msm_reset() is broken because after resetting the hardware, it > > > unconditionally asserts RFR via SET_RFR. This enables flow regardless of > > > the current configuration, and would undo a previous flow disable > > > operation. It should instead de-assert RFR via RESET_RFR to block flow > > > until the hardware is reconfigured. msm_serial should rely on the client > > > to specify that flow should be enabled, either via mctrl() or the termios > > > structure, and only assert RFR in response to those triggers. > > > > > > Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") > > > Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> > > > --- > > > > Reviewed-by: Andy Gross <agross@kernel.org> > > > > Greg, can you pick this one up? > > > > Thanks, > > Andy > > Greg, will this be queued for 5.5? Yes, catching up now...
On Mon, Nov 4, 2019 at 9:41 AM Greg Kroah-Hartman <gregkh@linuxfoundation.org> wrote: > > On Sun, Nov 03, 2019 at 02:51:17PM -0700, Jeffrey Hugo wrote: > > On Sat, Oct 26, 2019 at 11:55 PM Andy Gross <agross@kernel.org> wrote: > > > > > > On Mon, Oct 21, 2019 at 08:46:16AM -0700, Jeffrey Hugo wrote: > > > > hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and > > > > Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca > > > > disables flow, configures the uart baudrate, and then reenables flow - at > > > > which point an event is expected to be received over the uart from the > > > > wcn3990. It is observed that this event comes after the baudrate change > > > > but before hci_qca re-enables flow. This is unexpected, and is a result of > > > > msm_reset() being broken. > > > > > > > > According to the uart_dm hardware documentation, it is recommended that > > > > automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto > > > > hw flow control will manage RFR based on the configured watermark. When > > > > there is space to receive data, the hw will assert RFR. When the watermark > > > > is hit, the hw will de-assert RFR. > > > > > > > > The hardware documentation indicates that RFR can me manually managed via > > > > CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR > > > > de-asserts RFR. > > > > > > > > msm_reset() is broken because after resetting the hardware, it > > > > unconditionally asserts RFR via SET_RFR. This enables flow regardless of > > > > the current configuration, and would undo a previous flow disable > > > > operation. It should instead de-assert RFR via RESET_RFR to block flow > > > > until the hardware is reconfigured. msm_serial should rely on the client > > > > to specify that flow should be enabled, either via mctrl() or the termios > > > > structure, and only assert RFR in response to those triggers. > > > > > > > > Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") > > > > Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> > > > > --- > > > > > > Reviewed-by: Andy Gross <agross@kernel.org> > > > > > > Greg, can you pick this one up? > > > > > > Thanks, > > > Andy > > > > Greg, will this be queued for 5.5? > > Yes, catching up now... Excellent, thank you very much.
diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c index 3657a24913fc..00964b6e4ac1 100644 --- a/drivers/tty/serial/msm_serial.c +++ b/drivers/tty/serial/msm_serial.c @@ -980,6 +980,7 @@ static unsigned int msm_get_mctrl(struct uart_port *port) static void msm_reset(struct uart_port *port) { struct msm_port *msm_port = UART_TO_MSM(port); + unsigned int mr; /* reset everything */ msm_write(port, UART_CR_CMD_RESET_RX, UART_CR); @@ -987,7 +988,10 @@ static void msm_reset(struct uart_port *port) msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR); msm_write(port, UART_CR_CMD_RESET_BREAK_INT, UART_CR); msm_write(port, UART_CR_CMD_RESET_CTS, UART_CR); - msm_write(port, UART_CR_CMD_SET_RFR, UART_CR); + msm_write(port, UART_CR_CMD_RESET_RFR, UART_CR); + mr = msm_read(port, UART_MR1); + mr &= ~UART_MR1_RX_RDY_CTL; + msm_write(port, mr, UART_MR1); /* Disable DM modes */ if (msm_port->is_uartdm)
hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca disables flow, configures the uart baudrate, and then reenables flow - at which point an event is expected to be received over the uart from the wcn3990. It is observed that this event comes after the baudrate change but before hci_qca re-enables flow. This is unexpected, and is a result of msm_reset() being broken. According to the uart_dm hardware documentation, it is recommended that automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto hw flow control will manage RFR based on the configured watermark. When there is space to receive data, the hw will assert RFR. When the watermark is hit, the hw will de-assert RFR. The hardware documentation indicates that RFR can me manually managed via CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR de-asserts RFR. msm_reset() is broken because after resetting the hardware, it unconditionally asserts RFR via SET_RFR. This enables flow regardless of the current configuration, and would undo a previous flow disable operation. It should instead de-assert RFR via RESET_RFR to block flow until the hardware is reconfigured. msm_serial should rely on the client to specify that flow should be enabled, either via mctrl() or the termios structure, and only assert RFR in response to those triggers. Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> --- v2: -mask out RX_RDY_CTL in msm_reset() to close a small race window for RFR drivers/tty/serial/msm_serial.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)