| Message ID | 20210101022451.21882-1-shawn.guo@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: qcom: c630: keep both touchpad devices enabled | expand |
Hi Shawn, it seems like by doing so you're overwriting the I2C host pinctrl, so (unless that's intentional) the more correct fix would be: pinctrl-0 = <&qup_i2c3_default &i2c3_hid_active>; Konrad
On Fri, Jan 1, 2021 at 10:32 PM Konrad Dybcio <konrad.dybcio@somainline.org> wrote: > > Hi Shawn, > > it seems like by doing so you're overwriting the I2C host pinctrl, so (unless that's intentional) the more correct fix would be: > > pinctrl-0 = <&qup_i2c3_default &i2c3_hid_active>; Ha, yes, I missed that there is already some default pinctrl state set up in sdm845.dtsi. I will fix it with v2. Thanks for spotting it, Konrad! Shawn
diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts index dcfe66f169f9..802966e11152 100644 --- a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts +++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts @@ -353,6 +353,8 @@ &i2c3 { status = "okay"; clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_hid_active>; tsel: hid@15 { compatible = "hid-over-i2c"; @@ -360,9 +362,6 @@ hid-descr-addr = <0x1>; interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_HIGH>; - - pinctrl-names = "default"; - pinctrl-0 = <&i2c3_hid_active>; }; tsc2: hid@2c { @@ -371,11 +370,6 @@ hid-descr-addr = <0x20>; interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_HIGH>; - - pinctrl-names = "default"; - pinctrl-0 = <&i2c3_hid_active>; - - status = "disabled"; }; };
Indicated by AML code in ACPI table, the touchpad in-use could be found on two possible slave addresses on &i2c3, i.e. hid@15 and hid@2c. And which one is in-use can be determined by reading another address on the I2C bus. Unfortunately, for DT boot, there is currently no support in firmware to make this check and patch DT accordingly. This results in a non-functional touchpad on those C630 devices with hid@2c. As i2c-hid driver will stop probing the device if there is nothing on the slave address, we can actually keep both devices enabled in DT, and i2c-hid driver will only probe the existing one. The only problem is that we cannot set up pinctrl in both device nodes, as two devices with the same pinctrl will cause pin conflict that makes the second device fail to probe. Let's move the pinctrl state up to parent node to solve this problem. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> --- arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts | 10 ++-------- 1 file changed, 2 insertions(+), 8 deletions(-)