| Message ID | 20210127123054.263231-6-vkoul@kernel.org (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
| Series | Add binding and dts for Qualcomm SM8350 SoC | expand |
Hi Vinod, On 2021-01-27 18:00, Vinod Koul wrote: > Add basic devicetree support for Qualcomm Technologies, Inc SM8350 SoC. > This adds gcc, pinctrl, reserved memory, uart, cpu nodes for this SoC. > > Signed-off-by: Vinod Koul <vkoul@kernel.org> > --- > arch/arm64/boot/dts/qcom/sm8350.dtsi | 499 +++++++++++++++++++++++++++ > 1 file changed, 499 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/sm8350.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi > b/arch/arm64/boot/dts/qcom/sm8350.dtsi > new file mode 100644 > index 000000000000..29af0b931690 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi > @@ -0,0 +1,499 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2020, Linaro Limaited > + */ > + > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/clock/qcom,rpmh.h> > +#include <dt-bindings/mailbox/qcom-ipcc.h> > +#include <dt-bindings/power/qcom-aoss-qmp.h> > +#include <dt-bindings/power/qcom-rpmpd.h> > +#include <dt-bindings/soc/qcom,rpmh-rsc.h> > + > +/ { > + interrupt-parent = <&intc>; > + > + #address-cells = <2>; > + #size-cells = <2>; > + > + chosen { }; > + > + clocks { > + xo_board: xo-board { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <38400000>; > + clock-output-names = "xo_board"; > + }; > + > + sleep_clk: sleep-clk { > + compatible = "fixed-clock"; > + clock-frequency = <32000>; > + #clock-cells = <0>; > + }; > + }; > + > + cpus { > + #address-cells = <2>; > + #size-cells = <0>; > + > + CPU0: cpu@0 { > + device_type = "cpu"; > + compatible = "qcom,kryo685"; > + reg = <0x0 0x0>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + L2_0: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + L3_0: l3-cache { > + compatible = "cache"; > + }; > + }; > + }; > + > + CPU1: cpu@100 { > + device_type = "cpu"; > + compatible = "qcom,kryo685"; > + reg = <0x0 0x100>; > + enable-method = "psci"; > + next-level-cache = <&L2_100>; > + L2_100: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU2: cpu@200 { > + device_type = "cpu"; > + compatible = "qcom,kryo685"; > + reg = <0x0 0x200>; > + enable-method = "psci"; > + next-level-cache = <&L2_200>; > + L2_200: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU3: cpu@300 { > + device_type = "cpu"; > + compatible = "qcom,kryo685"; > + reg = <0x0 0x300>; > + enable-method = "psci"; > + next-level-cache = <&L2_300>; > + L2_300: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU4: cpu@400 { > + device_type = "cpu"; > + compatible = "qcom,kryo685"; > + reg = <0x0 0x400>; > + enable-method = "psci"; > + next-level-cache = <&L2_400>; > + L2_400: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU5: cpu@500 { > + device_type = "cpu"; > + compatible = "qcom,kryo685"; > + reg = <0x0 0x500>; > + enable-method = "psci"; > + next-level-cache = <&L2_500>; > + L2_500: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + > + }; > + > + CPU6: cpu@600 { > + device_type = "cpu"; > + compatible = "qcom,kryo685"; > + reg = <0x0 0x600>; > + enable-method = "psci"; > + next-level-cache = <&L2_600>; > + L2_600: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU7: cpu@700 { > + device_type = "cpu"; > + compatible = "qcom,kryo685"; > + reg = <0x0 0x700>; > + enable-method = "psci"; > + next-level-cache = <&L2_700>; > + L2_700: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + }; > + > + firmware { > + scm: scm { > + compatible = "qcom,scm-sm8350", "qcom,scm"; > + #reset-cells = <1>; > + }; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + /* We expect the bootloader to fill in the size */ > + reg = <0x0 0x80000000 0x0 0x0>; > + }; > + > + pmu { > + compatible = "arm,armv8-pmuv3"; > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + reserved_memory: reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + hyp_mem: memory@80000000 { > + reg = <0x0 0x80000000 0x0 0x600000>; > + no-map; > + }; > + > + xbl_aop_mem: memory@80700000 { > + no-map; > + reg = <0x0 0x80700000 0x0 0x160000>; > + }; > + > + cmd_db: memory@80860000 { > + compatible = "qcom,cmd-db"; > + reg = <0x0 0x80860000 0x0 0x20000>; > + no-map; > + }; > + > + reserved_xbl_uefi_log: memory@80880000 { > + reg = <0x0 0x80880000 0x0 0x14000>; > + no-map; > + }; > + > + smem_mem: memory@80900000 { > + reg = <0x0 0x80900000 0x0 0x200000>; > + no-map; > + }; > + > + cpucp_fw_mem: memory@80b00000 { > + reg = <0x0 0x80b00000 0x0 0x100000>; > + no-map; > + }; > + > + cdsp_secure_heap: memory@80c00000 { > + reg = <0x0 0x80c00000 0x0 0x4600000>; > + no-map; > + }; > + > + pil_camera_mem: mmeory@85200000 { > + reg = <0x0 0x85200000 0x0 0x500000>; > + no-map; > + }; > + > + pil_video_mem: memory@85700000 { > + reg = <0x0 0x85700000 0x0 0x500000>; > + no-map; > + }; > + > + pil_cvp_mem: memory@85c00000 { > + reg = <0x0 0x85c00000 0x0 0x500000>; > + no-map; > + }; > + > + pil_adsp_mem: memory@86100000 { > + reg = <0x0 0x86100000 0x0 0x2100000>; > + no-map; > + }; > + > + pil_slpi_mem: memory@88200000 { > + reg = <0x0 0x88200000 0x0 0x1500000>; > + no-map; > + }; > + > + pil_cdsp_mem: memory@89700000 { > + reg = <0x0 0x89700000 0x0 0x1e00000>; > + no-map; > + }; > + > + pil_ipa_fw_mem: memory@8b500000 { > + reg = <0x0 0x8b500000 0x0 0x10000>; > + no-map; > + }; > + > + pil_ipa_gsi_mem: memory@8b510000 { > + reg = <0x0 0x8b510000 0x0 0xa000>; > + no-map; > + }; > + > + pil_gpu_mem: memory@8b51a000 { > + reg = <0x0 0x8b51a000 0x0 0x2000>; > + no-map; > + }; > + > + pil_spss_mem: memory@8b600000 { > + reg = <0x0 0x8b600000 0x0 0x100000>; > + no-map; > + }; > + > + pil_modem_mem: memory@8b800000 { > + reg = <0x0 0x8b800000 0x0 0x10000000>; > + no-map; > + }; > + > + hyp_reserved_mem: memory@d0000000 { > + reg = <0x0 0xd0000000 0x0 0x800000>; > + no-map; > + }; > + > + pil_trustedvm_mem: memory@d0800000 { > + reg = <0x0 0xd0800000 0x0 0x76f7000>; > + no-map; > + }; > + > + qrtr_shbuf: memory@d7ef7000 { > + reg = <0x0 0xd7ef7000 0x0 0x9000>; > + no-map; > + }; > + > + chan0_shbuf: memory@d7f00000 { > + reg = <0x0 0xd7f00000 0x0 0x80000>; > + no-map; > + }; > + > + chan1_shbuf: memory@d7f80000 { > + reg = <0x0 0xd7f80000 0x0 0x80000>; > + no-map; > + }; > + > + removed_mem: memory@d8800000 { > + reg = <0x0 0xd8800000 0x0 0x6800000>; > + no-map; > + }; > + }; > + > + smem: qcom,smem { > + compatible = "qcom,smem"; > + memory-region = <&smem_mem>; > + hwlocks = <&tcsr_mutex 3>; > + }; > + > + soc: soc@0 { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges = <0 0 0 0 0x10 0>; > + dma-ranges = <0 0 0 0 0x10 0>; > + compatible = "simple-bus"; > + > + gcc: clock-controller@100000 { > + compatible = "qcom,gcc-sm8350"; > + reg = <0x0 0x00100000 0x0 0x1f0000>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + #power-domain-cells = <1>; > + clock-names = "bi_tcxo", "sleep_clk"; > + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; > + }; > + > + ipcc: mailbox@408000 { > + compatible = "qcom,sm8350-ipcc", "qcom,ipcc"; > + reg = <0 0x00408000 0 0x1000>; > + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <3>; > + #mbox-cells = <2>; > + }; > + > + qupv3_id_1: geniqup@9c0000 { > + compatible = "qcom,geni-se-qup"; > + reg = <0x0 0x009c0000 0x0 0x6000>; > + clock-names = "m-ahb", "s-ahb"; > + clocks = <&gcc 121>, > + <&gcc 122>; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + status = "disabled"; > + > + uart2: serial@98c000 { > + compatible = "qcom,geni-debug-uart"; > + reg = <0 0x0098c000 0 0x4000>; > + clock-names = "se"; > + clocks = <&gcc 83>; > + pinctrl-names = "default"; > + pinctrl-0 = <&qup_uart3_default_state>; > + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + }; > + > + tcsr_mutex: hwlock@1f40000 { > + compatible = "qcom,tcsr-mutex"; > + reg = <0x0 0x01f40000 0x0 0x40000>; > + #hwlock-cells = <1>; > + }; > + > + pdc: interrupt-controller@b220000 { > + compatible = "qcom,sm8350-pdc", "qcom,pdc"; > + reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; > + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, <55 306 > 4>, > + <59 312 3>, <62 374 2>, <64 434 2>, <66 438 3>, > + <69 86 1>, <70 520 54>, <124 609 31>, <155 63 1>, > + <156 716 12>; > + #interrupt-cells = <2>; > + interrupt-parent = <&intc>; > + interrupt-controller; > + }; > + > + aoss_qmp: qmp@c300000 { > + compatible = "qcom,sm8350-aoss-qmp"; > + reg = <0 0x0c300000 0 0x100000>; > + interrupts-extended = <&ipcc IPCC_CLIENT_AOP > IPCC_MPROC_SIGNAL_GLINK_QMP > + IRQ_TYPE_EDGE_RISING>; > + mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>; > + > + #clock-cells = <0>; > + #power-domain-cells = <1>; > + }; > + > + tlmm: pinctrl@f100000 { > + compatible = "qcom,sm8350-tlmm"; > + reg = <0 0x0f100000 0 0x300000>; > + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + gpio-ranges = <&tlmm 0 0 203>; > + > + qup_uart3_default_state: qup-uart3-default-state { > + rx { > + pins = "gpio18"; > + function = "qup3"; > + }; > + tx { > + pins = "gpio19"; > + function = "qup3"; > + }; > + }; > + }; > + > + intc: interrupt-controller@17a00000 { > + compatible = "arm,gic-v3"; > + #interrupt-cells = <3>; > + interrupt-controller; > + reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ > + <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + timer@17c20000 { > + compatible = "arm,armv7-timer-mem"; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + reg = <0x0 0x17c20000 0x0 0x1000>; > + clock-frequency = <19200000>; > + > + frame@17c21000 { > + frame-number = <0>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c21000 0x0 0x1000>, > + <0x0 0x17c22000 0x0 0x1000>; > + }; > + > + frame@17c23000 { > + frame-number = <1>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c23000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c25000 { > + frame-number = <2>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c25000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c27000 { > + frame-number = <3>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c27000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c29000 { > + frame-number = <4>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c29000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c2b000 { > + frame-number = <5>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c2b000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c2d000 { > + frame-number = <6>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c2d000 0x0 0x1000>; > + status = "disabled"; > + }; > + }; > + > + apps_rsc: rsc@18200000 { > + label = "apps_rsc"; > + compatible = "qcom,rpmh-rsc"; > + reg = <0x0 0x18200000 0x0 0x10000>, > + <0x0 0x18210000 0x0 0x10000>, > + <0x0 0x18220000 0x0 0x10000>; > + reg-names = "drv-0", "drv-1", "drv-2"; > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > + qcom,tcs-offset = <0xd00>; > + qcom,drv-id = <2>; > + qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>, > + <WAKE_TCS 3>, <CONTROL_TCS 1>; > + > + rpmhcc: clock-controller { > + compatible = "qcom,sm8350-rpmh-clk"; > + #clock-cells = <1>; > + clock-names = "xo"; > + clocks = <&xo_board>; > + }; > + > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | > IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; The last interrupt should be hypervisor physical interrupt(10) not 12(hyp virtual). It works currently with android bootloaders because the host linux kernel will run at EL1 and will use EL1 physical timer interrupt(14), but if we ever have the host kernel run in EL2(for example, chrome) then we will not receive any timer interrupts. Thanks, Sai
Hi Sai, On 27-01-21, 18:37, Sai Prakash Ranjan wrote: > Hi Vinod, > > On 2021-01-27 18:00, Vinod Koul wrote: > > + timer { > > + compatible = "arm,armv8-timer"; > > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | > > IRQ_TYPE_LEVEL_LOW)>, > > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, > > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, > > + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; > > The last interrupt should be hypervisor physical interrupt(10) not 12(hyp > virtual). > It works currently with android bootloaders because the host linux kernel > will run > at EL1 and will use EL1 physical timer interrupt(14), but if we ever have > the host > kernel run in EL2(for example, chrome) then we will not receive any timer > interrupts. I got these values from downstream and used them as is. I will update and also check documentation. Thanks for pointing out
Hi Vinod, On 2021-01-27 21:03, Vinod Koul wrote: > Hi Sai, > > On 27-01-21, 18:37, Sai Prakash Ranjan wrote: >> Hi Vinod, >> >> On 2021-01-27 18:00, Vinod Koul wrote: > >> > + timer { >> > + compatible = "arm,armv8-timer"; >> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | >> > IRQ_TYPE_LEVEL_LOW)>, >> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, >> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, >> > + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; >> >> The last interrupt should be hypervisor physical interrupt(10) not >> 12(hyp >> virtual). >> It works currently with android bootloaders because the host linux >> kernel >> will run >> at EL1 and will use EL1 physical timer interrupt(14), but if we ever >> have >> the host >> kernel run in EL2(for example, chrome) then we will not receive any >> timer >> interrupts. > > I got these values from downstream and used them as is. I will update > and also check documentation. Thanks for pointing out Yes looks like lot of SoC dtsi entries in downstream got it wrong. I see upstream sm8250 also missed this. We learnt it the hard way spending lot of time debugging why we are not able to reach the console(because no timer interrupts) during bringup on a system with kernel running in EL2(with VHE). I will try to reach out to baseport guys to make sure they take care of it in future. Thanks, Sai
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi new file mode 100644 index 000000000000..29af0b931690 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -0,0 +1,499 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Linaro Limaited + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,rpmh.h> +#include <dt-bindings/mailbox/qcom-ipcc.h> +#include <dt-bindings/power/qcom-aoss-qmp.h> +#include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-sm8350", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x80000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hyp_mem: memory@80000000 { + reg = <0x0 0x80000000 0x0 0x600000>; + no-map; + }; + + xbl_aop_mem: memory@80700000 { + no-map; + reg = <0x0 0x80700000 0x0 0x160000>; + }; + + cmd_db: memory@80860000 { + compatible = "qcom,cmd-db"; + reg = <0x0 0x80860000 0x0 0x20000>; + no-map; + }; + + reserved_xbl_uefi_log: memory@80880000 { + reg = <0x0 0x80880000 0x0 0x14000>; + no-map; + }; + + smem_mem: memory@80900000 { + reg = <0x0 0x80900000 0x0 0x200000>; + no-map; + }; + + cpucp_fw_mem: memory@80b00000 { + reg = <0x0 0x80b00000 0x0 0x100000>; + no-map; + }; + + cdsp_secure_heap: memory@80c00000 { + reg = <0x0 0x80c00000 0x0 0x4600000>; + no-map; + }; + + pil_camera_mem: mmeory@85200000 { + reg = <0x0 0x85200000 0x0 0x500000>; + no-map; + }; + + pil_video_mem: memory@85700000 { + reg = <0x0 0x85700000 0x0 0x500000>; + no-map; + }; + + pil_cvp_mem: memory@85c00000 { + reg = <0x0 0x85c00000 0x0 0x500000>; + no-map; + }; + + pil_adsp_mem: memory@86100000 { + reg = <0x0 0x86100000 0x0 0x2100000>; + no-map; + }; + + pil_slpi_mem: memory@88200000 { + reg = <0x0 0x88200000 0x0 0x1500000>; + no-map; + }; + + pil_cdsp_mem: memory@89700000 { + reg = <0x0 0x89700000 0x0 0x1e00000>; + no-map; + }; + + pil_ipa_fw_mem: memory@8b500000 { + reg = <0x0 0x8b500000 0x0 0x10000>; + no-map; + }; + + pil_ipa_gsi_mem: memory@8b510000 { + reg = <0x0 0x8b510000 0x0 0xa000>; + no-map; + }; + + pil_gpu_mem: memory@8b51a000 { + reg = <0x0 0x8b51a000 0x0 0x2000>; + no-map; + }; + + pil_spss_mem: memory@8b600000 { + reg = <0x0 0x8b600000 0x0 0x100000>; + no-map; + }; + + pil_modem_mem: memory@8b800000 { + reg = <0x0 0x8b800000 0x0 0x10000000>; + no-map; + }; + + hyp_reserved_mem: memory@d0000000 { + reg = <0x0 0xd0000000 0x0 0x800000>; + no-map; + }; + + pil_trustedvm_mem: memory@d0800000 { + reg = <0x0 0xd0800000 0x0 0x76f7000>; + no-map; + }; + + qrtr_shbuf: memory@d7ef7000 { + reg = <0x0 0xd7ef7000 0x0 0x9000>; + no-map; + }; + + chan0_shbuf: memory@d7f00000 { + reg = <0x0 0xd7f00000 0x0 0x80000>; + no-map; + }; + + chan1_shbuf: memory@d7f80000 { + reg = <0x0 0xd7f80000 0x0 0x80000>; + no-map; + }; + + removed_mem: memory@d8800000 { + reg = <0x0 0xd8800000 0x0 0x6800000>; + no-map; + }; + }; + + smem: qcom,smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; + }; + + soc: soc@0 { + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0 0x10 0>; + dma-ranges = <0 0 0 0 0x10 0>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8350"; + reg = <0x0 0x00100000 0x0 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; + }; + + ipcc: mailbox@408000 { + compatible = "qcom,sm8350-ipcc", "qcom,ipcc"; + reg = <0 0x00408000 0 0x1000>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <3>; + #mbox-cells = <2>; + }; + + qupv3_id_1: geniqup@9c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x009c0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc 121>, + <&gcc 122>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + uart2: serial@98c000 { + compatible = "qcom,geni-debug-uart"; + reg = <0 0x0098c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc 83>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart3_default_state>; + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + + tcsr_mutex: hwlock@1f40000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x0 0x01f40000 0x0 0x40000>; + #hwlock-cells = <1>; + }; + + pdc: interrupt-controller@b220000 { + compatible = "qcom,sm8350-pdc", "qcom,pdc"; + reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, <55 306 4>, + <59 312 3>, <62 374 2>, <64 434 2>, <66 438 3>, + <69 86 1>, <70 520 54>, <124 609 31>, <155 63 1>, + <156 716 12>; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + aoss_qmp: qmp@c300000 { + compatible = "qcom,sm8350-aoss-qmp"; + reg = <0 0x0c300000 0 0x100000>; + interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>; + + #clock-cells = <0>; + #power-domain-cells = <1>; + }; + + tlmm: pinctrl@f100000 { + compatible = "qcom,sm8350-tlmm"; + reg = <0 0x0f100000 0 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 203>; + + qup_uart3_default_state: qup-uart3-default-state { + rx { + pins = "gpio18"; + function = "qup3"; + }; + tx { + pins = "gpio19"; + function = "qup3"; + }; + }; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ + <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17c20000 { + compatible = "arm,armv7-timer-mem"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + reg = <0x0 0x17c20000 0x0 0x1000>; + clock-frequency = <19200000>; + + frame@17c21000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c21000 0x0 0x1000>, + <0x0 0x17c22000 0x0 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c23000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c25000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c27000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c29000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c2b000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c2d000 0x0 0x1000>; + status = "disabled"; + }; + }; + + apps_rsc: rsc@18200000 { + label = "apps_rsc"; + compatible = "qcom,rpmh-rsc"; + reg = <0x0 0x18200000 0x0 0x10000>, + <0x0 0x18210000 0x0 0x10000>, + <0x0 0x18220000 0x0 0x10000>; + reg-names = "drv-0", "drv-1", "drv-2"; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>, + <WAKE_TCS 3>, <CONTROL_TCS 1>; + + rpmhcc: clock-controller { + compatible = "qcom,sm8350-rpmh-clk"; + #clock-cells = <1>; + clock-names = "xo"; + clocks = <&xo_board>; + }; + + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; + }; +};
Add basic devicetree support for Qualcomm Technologies, Inc SM8350 SoC. This adds gcc, pinctrl, reserved memory, uart, cpu nodes for this SoC. Signed-off-by: Vinod Koul <vkoul@kernel.org> --- arch/arm64/boot/dts/qcom/sm8350.dtsi | 499 +++++++++++++++++++++++++++ 1 file changed, 499 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8350.dtsi