@@ -4,6 +4,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-sm8350.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-aoss-qmp.h>
@@ -430,8 +431,8 @@ qupv3_id_1: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x009c0000 0x0 0x6000>;
clock-names = "m-ahb", "s-ahb";
- clocks = <&gcc 121>,
- <&gcc 122>;
+ clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
@@ -441,7 +442,7 @@ uart2: serial@98c000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x0098c000 0 0x4000>;
clock-names = "se";
- clocks = <&gcc 83>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_uart3_default_state>;
interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
@@ -797,10 +798,10 @@ ufs_mem_hc: ufshc@1d84000 {
phy-names = "ufsphy";
lanes-per-direction = <2>;
#reset-cells = <1>;
- resets = <&gcc 25>;
+ resets = <&gcc GCC_UFS_PHY_BCR>;
reset-names = "rst";
- power-domains = <&gcc 3>;
+ power-domains = <&gcc UFS_PHY_GDSC>;
iommus = <&apps_smmu 0xe0 0x0>;
@@ -816,14 +817,14 @@ ufs_mem_hc: ufshc@1d84000 {
"rx_lane1_sync_clk";
clocks =
<&rpmhcc RPMH_CXO_CLK>,
- <&gcc 155>,
- <&gcc 16>,
- <&gcc 154>,
- <&gcc 170>,
+ <&gcc GCC_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_UFS_PHY_AHB_CLK>,
+ <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
- <&gcc 168>,
- <&gcc 164>,
- <&gcc 166>;
+ <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
freq-table-hz =
<75000000 300000000>,
<75000000 300000000>,
@@ -847,7 +848,7 @@ ufs_mem_phy: phy@1d87000 {
clock-names = "ref",
"ref_aux";
clocks = <&rpmhcc RPMH_CXO_CLK>,
- <&gcc 161>;
+ <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
resets = <&ufs_mem_hc 0>;
reset-names = "ufsphy";
@@ -953,7 +954,7 @@ usb_1_hsphy: phy@88e3000 {
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "ref";
- resets = <&gcc 20>;
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
};
usb_2_hsphy: phy@88e4000 {
@@ -966,7 +967,7 @@ usb_2_hsphy: phy@88e4000 {
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "ref";
- resets = <&gcc 21>;
+ resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
};
usb_1_qmpphy: phy-wrapper@88e9000 {
@@ -980,13 +981,13 @@ usb_1_qmpphy: phy-wrapper@88e9000 {
#size-cells = <2>;
ranges;
- clocks = <&gcc 187>,
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
- <&gcc 189>;
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
clock-names = "aux", "ref_clk_src", "com_aux";
- resets = <&gcc 28>,
- <&gcc 30>;
+ resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_PHY_PRIM_BCR>;
reset-names = "phy", "common";
usb_1_ssphy: phy@88e9200 {
@@ -998,7 +999,7 @@ usb_1_ssphy: phy@88e9200 {
<0 0x088e9a00 0 0x100>;
#phy-cells = <0>;
#clock-cells = <1>;
- clocks = <&gcc 190>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
clock-names = "pipe0";
clock-output-names = "usb3_phy_pipe_clk_src";
};
@@ -1013,14 +1014,14 @@ usb_2_qmpphy: phy-wrapper@88eb000 {
#size-cells = <2>;
ranges;
- clocks = <&gcc 193>,
+ clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
- <&gcc 192>,
- <&gcc 195>;
+ <&gcc GCC_USB3_SEC_CLKREF_EN>,
+ <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
clock-names = "aux", "ref_clk_src", "ref", "com_aux";
- resets = <&gcc 33>,
- <&gcc 31>;
+ resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+ <&gcc GCC_USB3_PHY_SEC_BCR>;
reset-names = "phy", "common";
usb_2_ssphy: phy@88ebe00 {
@@ -1029,7 +1030,7 @@ usb_2_ssphy: phy@88ebe00 {
<0 0x088eb200 0 0x1100>;
#phy-cells = <0>;
#clock-cells = <1>;
- clocks = <&gcc 196>;
+ clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
clock-names = "pipe0";
clock-output-names = "usb3_uni_phy_pipe_clk_src";
};
@@ -1043,16 +1044,16 @@ usb_1: usb@a6f8800 {
#size-cells = <2>;
ranges;
- clocks = <&gcc 23>,
- <&gcc 173>,
- <&gcc 18>,
- <&gcc 176>,
- <&gcc 179>;
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
clock-names = "cfg_noc", "core", "iface", "mock_utmi",
"sleep";
- assigned-clocks = <&gcc 176>,
- <&gcc 173>;
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
assigned-clock-rates = <19200000>, <200000000>;
interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
@@ -1062,9 +1063,9 @@ usb_1: usb@a6f8800 {
interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
"dm_hs_phy_irq", "ss_phy_irq";
- power-domains = <&gcc 4>;
+ power-domains = <&gcc USB30_PRIM_GDSC>;
- resets = <&gcc 26>;
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
usb_1_dwc3: dwc3@a600000 {
compatible = "snps,dwc3";
@@ -1086,17 +1087,17 @@ usb_2: usb@a8f8800 {
#size-cells = <2>;
ranges;
- clocks = <&gcc 24>,
- <&gcc 180>,
- <&gcc 19>,
- <&gcc 183>,
- <&gcc 186>,
- <&gcc 192>;
+ clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_EN>;
clock-names = "cfg_noc", "core", "iface", "mock_utmi",
"sleep", "xo";
- assigned-clocks = <&gcc 183>,
- <&gcc 180>;
+ assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>;
assigned-clock-rates = <19200000>, <200000000>;
interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
@@ -1106,9 +1107,9 @@ usb_2: usb@a8f8800 {
interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
"dm_hs_phy_irq", "ss_phy_irq";
- power-domains = <&gcc 5>;
+ power-domains = <&gcc USB30_SEC_GDSC>;
- resets = <&gcc 27>;
+ resets = <&gcc GCC_USB30_SEC_BCR>;
usb_2_dwc3: dwc3@a800000 {
compatible = "snps,dwc3";
Now that we have GCC define, use the enums instead of numbers in the DTS Signed-off-by: Vinod Koul <vkoul@kernel.org> --- arch/arm64/boot/dts/qcom/sm8350.dtsi | 91 ++++++++++++++-------------- 1 file changed, 46 insertions(+), 45 deletions(-)