| Message ID | 20220210103423.271016-9-vkoul@kernel.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | drm/msm: Add Display Stream Compression Support | expand |
On 10/02/2022 13:34, Vinod Koul wrote: > We cannot enable mode_3d when we are using the DSC. So pass > configuration to detect DSC is enabled and not enable mode_3d > when we are using DSC > > We add a helper dpu_encoder_helper_get_dsc() to detect dsc > enabled and pass this to .setup_intf_cfg() > > Signed-off-by: Vinod Koul <vkoul@kernel.org> You seem to insist on this. Ok, lets agree that you did not test any other topologies and let anybody adding support for SDE_RM_TOPOLOGY_DUALPIPE_3DMERGE_DSC handle this. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > --- > drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c | 4 ++++ > drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 4 ++++ > drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c | 7 ++++++- > 3 files changed, 14 insertions(+), 1 deletion(-) > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c > index 34a6940d12c5..ed37a4c21596 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c > @@ -70,6 +70,10 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg( > intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_CMD; > intf_cfg.stream_sel = cmd_enc->stream_sel; > intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc); > + intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc); > + if (intf_cfg.dsc) > + intf_cfg.mode_3d = 0; > + > ctl->ops.setup_intf_cfg(ctl, &intf_cfg); > } > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > index ddd9d89cd456..218009855fca 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > @@ -284,6 +284,10 @@ static void dpu_encoder_phys_vid_setup_timing_engine( > intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_VID; > intf_cfg.stream_sel = 0; /* Don't care value for video mode */ > intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc); > + intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc); > + if (intf_cfg.dsc) > + intf_cfg.mode_3d = 0; > + > if (phys_enc->hw_pp->merge_3d) > intf_cfg.merge_3d = phys_enc->hw_pp->merge_3d->idx; > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c > index 49659165cea8..6d5268b7da90 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c > @@ -536,7 +536,12 @@ static void dpu_hw_ctl_intf_cfg(struct dpu_hw_ctl *ctx, > > intf_cfg |= (cfg->intf & 0xF) << 4; > > - if (cfg->mode_3d) { > + /* In DSC we can't set merge, so check for dsc and complain */ > + if (cfg->mode_3d && cfg->dsc) > + pr_err("DPU1: DSC and Merge 3D both are set!! it may not work\n"); > + > + /* set merge only when dsc is not set */ > + if (cfg->mode_3d && !cfg->dsc) { > intf_cfg |= BIT(19); > intf_cfg |= (cfg->mode_3d - 0x1) << 20; > }
On 2/10/2022 2:34 AM, Vinod Koul wrote: > We cannot enable mode_3d when we are using the DSC. So pass > configuration to detect DSC is enabled and not enable mode_3d > when we are using DSC > > We add a helper dpu_encoder_helper_get_dsc() to detect dsc > enabled and pass this to .setup_intf_cfg() > > Signed-off-by: Vinod Koul <vkoul@kernel.org> We should not use 3D mux only when we use DSC merge topology. I agree that today we use only 2-2-1 topology for DSC which means its using DSC merge. But generalizing that 3D mux should not be used for DSC is not right. You can detect DSC merge by checking if there are two encoders and one interface in the topology and if so, you can disable 3D mux. > --- > drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c | 4 ++++ > drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 4 ++++ > drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c | 7 ++++++- > 3 files changed, 14 insertions(+), 1 deletion(-) > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c > index 34a6940d12c5..ed37a4c21596 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c > @@ -70,6 +70,10 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg( > intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_CMD; > intf_cfg.stream_sel = cmd_enc->stream_sel; > intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc); > + intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc); > + if (intf_cfg.dsc) > + intf_cfg.mode_3d = 0; > + > ctl->ops.setup_intf_cfg(ctl, &intf_cfg); > } > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > index ddd9d89cd456..218009855fca 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > @@ -284,6 +284,10 @@ static void dpu_encoder_phys_vid_setup_timing_engine( > intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_VID; > intf_cfg.stream_sel = 0; /* Don't care value for video mode */ > intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc); > + intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc); > + if (intf_cfg.dsc) > + intf_cfg.mode_3d = 0; > + > if (phys_enc->hw_pp->merge_3d) > intf_cfg.merge_3d = phys_enc->hw_pp->merge_3d->idx; > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c > index 49659165cea8..6d5268b7da90 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c > @@ -536,7 +536,12 @@ static void dpu_hw_ctl_intf_cfg(struct dpu_hw_ctl *ctx, > > intf_cfg |= (cfg->intf & 0xF) << 4; > > - if (cfg->mode_3d) { > + /* In DSC we can't set merge, so check for dsc and complain */ > + if (cfg->mode_3d && cfg->dsc) > + pr_err("DPU1: DSC and Merge 3D both are set!! it may not work\n"); > + > + /* set merge only when dsc is not set */ > + if (cfg->mode_3d && !cfg->dsc) { > intf_cfg |= BIT(19); > intf_cfg |= (cfg->mode_3d - 0x1) << 20; > }
On 16-02-22, 19:11, Abhinav Kumar wrote: > > > On 2/10/2022 2:34 AM, Vinod Koul wrote: > > We cannot enable mode_3d when we are using the DSC. So pass > > configuration to detect DSC is enabled and not enable mode_3d > > when we are using DSC > > > > We add a helper dpu_encoder_helper_get_dsc() to detect dsc > > enabled and pass this to .setup_intf_cfg() > > > > Signed-off-by: Vinod Koul <vkoul@kernel.org> > > We should not use 3D mux only when we use DSC merge topology. > I agree that today we use only 2-2-1 topology for DSC which means its using > DSC merge. > > But generalizing that 3D mux should not be used for DSC is not right. > > You can detect DSC merge by checking if there are two encoders and one > interface in the topology and if so, you can disable 3D mux. Right now with DSC we disable that as suggested by Dmitry last time. Whenever we introduce merge we should revisit this, for now this should suffice
On 2/16/2022 10:10 PM, Vinod Koul wrote: > On 16-02-22, 19:11, Abhinav Kumar wrote: >> >> >> On 2/10/2022 2:34 AM, Vinod Koul wrote: >>> We cannot enable mode_3d when we are using the DSC. So pass >>> configuration to detect DSC is enabled and not enable mode_3d >>> when we are using DSC >>> >>> We add a helper dpu_encoder_helper_get_dsc() to detect dsc >>> enabled and pass this to .setup_intf_cfg() >>> >>> Signed-off-by: Vinod Koul <vkoul@kernel.org> >> >> We should not use 3D mux only when we use DSC merge topology. >> I agree that today we use only 2-2-1 topology for DSC which means its using >> DSC merge. >> >> But generalizing that 3D mux should not be used for DSC is not right. >> >> You can detect DSC merge by checking if there are two encoders and one >> interface in the topology and if so, you can disable 3D mux. > > Right now with DSC we disable that as suggested by Dmitry last time. > Whenever we introduce merge we should revisit this, for now this should > suffice > Sorry I didnt follow. The topology which you are supporting today IS DSC merge 2-2-1. I didnt get what you mean by "whenever we introduce". I didnt follow Dmitry's comment either. "anybody adding support for SDE_RM_TOPOLOGY_DUALPIPE_3DMERGE_DSC handle this." 3D mux shouldnt be used when DSC merge is used. The topology Dmitry is referring to will not use DSC merge but you are using it here and thats why you had to make this patch in the first place. So I am not sure why would someone who uses 3D merge topology worry about DSC merge. Your patch is the one which deals with the topology in question. What I am suggesting is a small but necessary improvement to this patch. All that you have to do is in query whether DSC merge is used from the topology. You can do it in multiple ways: 1) Either query this from the encoder 2) Store a bool "dsc_merge" in the intf_cfg
On 17/02/2022 09:33, Abhinav Kumar wrote: > > > On 2/16/2022 10:10 PM, Vinod Koul wrote: >> On 16-02-22, 19:11, Abhinav Kumar wrote: >>> >>> >>> On 2/10/2022 2:34 AM, Vinod Koul wrote: >>>> We cannot enable mode_3d when we are using the DSC. So pass >>>> configuration to detect DSC is enabled and not enable mode_3d >>>> when we are using DSC >>>> >>>> We add a helper dpu_encoder_helper_get_dsc() to detect dsc >>>> enabled and pass this to .setup_intf_cfg() >>>> >>>> Signed-off-by: Vinod Koul <vkoul@kernel.org> >>> >>> We should not use 3D mux only when we use DSC merge topology. >>> I agree that today we use only 2-2-1 topology for DSC which means its >>> using >>> DSC merge. >>> >>> But generalizing that 3D mux should not be used for DSC is not right. >>> >>> You can detect DSC merge by checking if there are two encoders and one >>> interface in the topology and if so, you can disable 3D mux. >> >> Right now with DSC we disable that as suggested by Dmitry last time. >> Whenever we introduce merge we should revisit this, for now this should >> suffice >> > > Sorry I didnt follow. > > The topology which you are supporting today IS DSC merge 2-2-1. I didnt > get what you mean by "whenever we introduce". > > I didnt follow Dmitry's comment either. > > "anybody adding support for SDE_RM_TOPOLOGY_DUALPIPE_3DMERGE_DSC handle > this." > > 3D mux shouldnt be used when DSC merge is used. > > The topology Dmitry is referring to will not use DSC merge but you are > using it here and thats why you had to make this patch in the first > place. So I am not sure why would someone who uses 3D merge topology > worry about DSC merge. Your patch is the one which deals with the > topology in question. > > What I am suggesting is a small but necessary improvement to this patch. It seems that we can replace this patch by changing dpu_encoder_helper_get_3d_blend_mode() to contain the following condition (instead of the one present there). Does the following seem correct to you: static inline enum dpu_3d_blend_mode dpu_encoder_helper_get_3d_blend_mode( struct dpu_encoder_phys *phys_enc) { struct dpu_crtc_state *dpu_cstate; if (!phys_enc || phys_enc->enable_state == DPU_ENC_DISABLING) return BLEND_3D_NONE; dpu_cstate = to_dpu_crtc_state(phys_enc->parent->crtc->state); + /* Use merge_3d unless DSCMERGE topology is used */ if (phys_enc->split_role == ENC_ROLE_SOLO && + hweight(dpu_encoder_helper_get_dsc(phys_enc)) != 1 && dpu_cstate->num_mixers == CRTC_DUAL_MIXERS) return BLEND_3D_H_ROW_INT; return BLEND_3D_NONE; } > > All that you have to do is in query whether DSC merge is used from the > topology. You can do it in multiple ways: > > 1) Either query this from the encoder > 2) Store a bool "dsc_merge" in the intf_cfg >
On 2/16/2022 11:12 PM, Dmitry Baryshkov wrote: > On 17/02/2022 09:33, Abhinav Kumar wrote: >> >> >> On 2/16/2022 10:10 PM, Vinod Koul wrote: >>> On 16-02-22, 19:11, Abhinav Kumar wrote: >>>> >>>> >>>> On 2/10/2022 2:34 AM, Vinod Koul wrote: >>>>> We cannot enable mode_3d when we are using the DSC. So pass >>>>> configuration to detect DSC is enabled and not enable mode_3d >>>>> when we are using DSC >>>>> >>>>> We add a helper dpu_encoder_helper_get_dsc() to detect dsc >>>>> enabled and pass this to .setup_intf_cfg() >>>>> >>>>> Signed-off-by: Vinod Koul <vkoul@kernel.org> >>>> >>>> We should not use 3D mux only when we use DSC merge topology. >>>> I agree that today we use only 2-2-1 topology for DSC which means >>>> its using >>>> DSC merge. >>>> >>>> But generalizing that 3D mux should not be used for DSC is not right. >>>> >>>> You can detect DSC merge by checking if there are two encoders and one >>>> interface in the topology and if so, you can disable 3D mux. >>> >>> Right now with DSC we disable that as suggested by Dmitry last time. >>> Whenever we introduce merge we should revisit this, for now this should >>> suffice >>> >> >> Sorry I didnt follow. >> >> The topology which you are supporting today IS DSC merge 2-2-1. I >> didnt get what you mean by "whenever we introduce". >> >> I didnt follow Dmitry's comment either. >> >> "anybody adding support for SDE_RM_TOPOLOGY_DUALPIPE_3DMERGE_DSC >> handle this." >> >> 3D mux shouldnt be used when DSC merge is used. >> >> The topology Dmitry is referring to will not use DSC merge but you are >> using it here and thats why you had to make this patch in the first >> place. So I am not sure why would someone who uses 3D merge topology >> worry about DSC merge. Your patch is the one which deals with the >> topology in question. >> >> What I am suggesting is a small but necessary improvement to this patch. > > It seems that we can replace this patch by changing > dpu_encoder_helper_get_3d_blend_mode() to contain the following > condition (instead of the one present there). Does the following seem > correct to you: > > static inline enum dpu_3d_blend_mode dpu_encoder_helper_get_3d_blend_mode( > struct dpu_encoder_phys *phys_enc) > { > struct dpu_crtc_state *dpu_cstate; > > if (!phys_enc || phys_enc->enable_state == DPU_ENC_DISABLING) > return BLEND_3D_NONE; > > dpu_cstate = to_dpu_crtc_state(phys_enc->parent->crtc->state); > > + /* Use merge_3d unless DSCMERGE topology is used */ > if (phys_enc->split_role == ENC_ROLE_SOLO && > + hweight(dpu_encoder_helper_get_dsc(phys_enc)) != 1 && > dpu_cstate->num_mixers == CRTC_DUAL_MIXERS) > return BLEND_3D_H_ROW_INT; > > return BLEND_3D_NONE; > } This will not be enough. To detect whether DSC merge is enabled you need to query the topology. The above condition only checks if DSC is enabled not DSC merge. So the above function can be modified to use a helper like below instead of the hweight. bool dpu_encoder_get_dsc_merge_info(struct dpu_encoder_virt *dpu_enc) { struct msm_display_topology topology = {0}; topology = dpu_encoder_get_topology(...); if (topology.num_dsc > topology.num_intf) return true; else return false; } if (!dpu_encoder_get_dsc_merge_info() && other conditions listed above) return BLEND_3D_H_ROW_INT; else BLEND_3D_NONE; > > >> >> All that you have to do is in query whether DSC merge is used from the >> topology. You can do it in multiple ways: >> >> 1) Either query this from the encoder >> 2) Store a bool "dsc_merge" in the intf_cfg >> > >
On 18/02/2022 23:46, Abhinav Kumar wrote: > > > On 2/16/2022 11:12 PM, Dmitry Baryshkov wrote: >> On 17/02/2022 09:33, Abhinav Kumar wrote: >>> >>> >>> On 2/16/2022 10:10 PM, Vinod Koul wrote: >>>> On 16-02-22, 19:11, Abhinav Kumar wrote: >>>>> >>>>> >>>>> On 2/10/2022 2:34 AM, Vinod Koul wrote: >>>>>> We cannot enable mode_3d when we are using the DSC. So pass >>>>>> configuration to detect DSC is enabled and not enable mode_3d >>>>>> when we are using DSC >>>>>> >>>>>> We add a helper dpu_encoder_helper_get_dsc() to detect dsc >>>>>> enabled and pass this to .setup_intf_cfg() >>>>>> >>>>>> Signed-off-by: Vinod Koul <vkoul@kernel.org> >>>>> >>>>> We should not use 3D mux only when we use DSC merge topology. >>>>> I agree that today we use only 2-2-1 topology for DSC which means >>>>> its using >>>>> DSC merge. >>>>> >>>>> But generalizing that 3D mux should not be used for DSC is not right. >>>>> >>>>> You can detect DSC merge by checking if there are two encoders and one >>>>> interface in the topology and if so, you can disable 3D mux. >>>> >>>> Right now with DSC we disable that as suggested by Dmitry last time. >>>> Whenever we introduce merge we should revisit this, for now this should >>>> suffice >>>> >>> >>> Sorry I didnt follow. >>> >>> The topology which you are supporting today IS DSC merge 2-2-1. I >>> didnt get what you mean by "whenever we introduce". >>> >>> I didnt follow Dmitry's comment either. >>> >>> "anybody adding support for SDE_RM_TOPOLOGY_DUALPIPE_3DMERGE_DSC >>> handle this." >>> >>> 3D mux shouldnt be used when DSC merge is used. >>> >>> The topology Dmitry is referring to will not use DSC merge but you >>> are using it here and thats why you had to make this patch in the >>> first place. So I am not sure why would someone who uses 3D merge >>> topology worry about DSC merge. Your patch is the one which deals >>> with the topology in question. >>> >>> What I am suggesting is a small but necessary improvement to this patch. >> >> It seems that we can replace this patch by changing >> dpu_encoder_helper_get_3d_blend_mode() to contain the following >> condition (instead of the one present there). Does the following seem >> correct to you: >> >> static inline enum dpu_3d_blend_mode >> dpu_encoder_helper_get_3d_blend_mode( >> struct dpu_encoder_phys *phys_enc) >> { >> struct dpu_crtc_state *dpu_cstate; >> >> if (!phys_enc || phys_enc->enable_state == DPU_ENC_DISABLING) >> return BLEND_3D_NONE; >> >> dpu_cstate = to_dpu_crtc_state(phys_enc->parent->crtc->state); >> >> + /* Use merge_3d unless DSCMERGE topology is used */ >> if (phys_enc->split_role == ENC_ROLE_SOLO && >> + hweight(dpu_encoder_helper_get_dsc(phys_enc)) != 1 && Yes, the correct should be: hweight(...) == 2 >> dpu_cstate->num_mixers == CRTC_DUAL_MIXERS) >> return BLEND_3D_H_ROW_INT; >> >> return BLEND_3D_NONE; >> } > > This will not be enough. To detect whether DSC merge is enabled you need > to query the topology. The above condition only checks if DSC is enabled > not DSC merge. > > So the above function can be modified to use a helper like below instead > of the hweight. > > bool dpu_encoder_get_dsc_merge_info(struct dpu_encoder_virt *dpu_enc) > { > struct msm_display_topology topology = {0}; > > topology = dpu_encoder_get_topology(...); > > if (topology.num_dsc > topology.num_intf) num_intf is 1 or 2. If it's one, the split_role is SOLO hweight would return a num of bits in the DSC mask. It's 0, 1 or 2. So, if the split_role is SOLO and hweight is 2, we get exactly your condition. Does that sound correct? > return true; > else > return false; > } > > if (!dpu_encoder_get_dsc_merge_info() && other conditions listed above) > return BLEND_3D_H_ROW_INT; > else > BLEND_3D_NONE; >> >> >>> >>> All that you have to do is in query whether DSC merge is used from >>> the topology. You can do it in multiple ways: >>> >>> 1) Either query this from the encoder >>> 2) Store a bool "dsc_merge" in the intf_cfg >>> >> >>
On 2/18/2022 1:21 PM, Dmitry Baryshkov wrote: > On 18/02/2022 23:46, Abhinav Kumar wrote: >> >> >> On 2/16/2022 11:12 PM, Dmitry Baryshkov wrote: >>> On 17/02/2022 09:33, Abhinav Kumar wrote: >>>> >>>> >>>> On 2/16/2022 10:10 PM, Vinod Koul wrote: >>>>> On 16-02-22, 19:11, Abhinav Kumar wrote: >>>>>> >>>>>> >>>>>> On 2/10/2022 2:34 AM, Vinod Koul wrote: >>>>>>> We cannot enable mode_3d when we are using the DSC. So pass >>>>>>> configuration to detect DSC is enabled and not enable mode_3d >>>>>>> when we are using DSC >>>>>>> >>>>>>> We add a helper dpu_encoder_helper_get_dsc() to detect dsc >>>>>>> enabled and pass this to .setup_intf_cfg() >>>>>>> >>>>>>> Signed-off-by: Vinod Koul <vkoul@kernel.org> >>>>>> >>>>>> We should not use 3D mux only when we use DSC merge topology. >>>>>> I agree that today we use only 2-2-1 topology for DSC which means >>>>>> its using >>>>>> DSC merge. >>>>>> >>>>>> But generalizing that 3D mux should not be used for DSC is not right. >>>>>> >>>>>> You can detect DSC merge by checking if there are two encoders and >>>>>> one >>>>>> interface in the topology and if so, you can disable 3D mux. >>>>> >>>>> Right now with DSC we disable that as suggested by Dmitry last time. >>>>> Whenever we introduce merge we should revisit this, for now this >>>>> should >>>>> suffice >>>>> >>>> >>>> Sorry I didnt follow. >>>> >>>> The topology which you are supporting today IS DSC merge 2-2-1. I >>>> didnt get what you mean by "whenever we introduce". >>>> >>>> I didnt follow Dmitry's comment either. >>>> >>>> "anybody adding support for SDE_RM_TOPOLOGY_DUALPIPE_3DMERGE_DSC >>>> handle this." >>>> >>>> 3D mux shouldnt be used when DSC merge is used. >>>> >>>> The topology Dmitry is referring to will not use DSC merge but you >>>> are using it here and thats why you had to make this patch in the >>>> first place. So I am not sure why would someone who uses 3D merge >>>> topology worry about DSC merge. Your patch is the one which deals >>>> with the topology in question. >>>> >>>> What I am suggesting is a small but necessary improvement to this >>>> patch. >>> >>> It seems that we can replace this patch by changing >>> dpu_encoder_helper_get_3d_blend_mode() to contain the following >>> condition (instead of the one present there). Does the following seem >>> correct to you: >>> >>> static inline enum dpu_3d_blend_mode >>> dpu_encoder_helper_get_3d_blend_mode( >>> struct dpu_encoder_phys *phys_enc) >>> { >>> struct dpu_crtc_state *dpu_cstate; >>> >>> if (!phys_enc || phys_enc->enable_state == DPU_ENC_DISABLING) >>> return BLEND_3D_NONE; >>> >>> dpu_cstate = to_dpu_crtc_state(phys_enc->parent->crtc->state); >>> >>> + /* Use merge_3d unless DSCMERGE topology is used */ >>> if (phys_enc->split_role == ENC_ROLE_SOLO && >>> + hweight(dpu_encoder_helper_get_dsc(phys_enc)) != 1 && > > Yes, the correct should be: > hweight(...) == 2 > >>> dpu_cstate->num_mixers == CRTC_DUAL_MIXERS) >>> return BLEND_3D_H_ROW_INT; >>> >>> return BLEND_3D_NONE; >>> } >> >> This will not be enough. To detect whether DSC merge is enabled you >> need to query the topology. The above condition only checks if DSC is >> enabled not DSC merge. >> >> So the above function can be modified to use a helper like below >> instead of the hweight. >> >> bool dpu_encoder_get_dsc_merge_info(struct dpu_encoder_virt *dpu_enc) >> { >> struct msm_display_topology topology = {0}; >> >> topology = dpu_encoder_get_topology(...); >> >> if (topology.num_dsc > topology.num_intf) > > num_intf is 1 or 2. If it's one, the split_role is SOLO > hweight would return a num of bits in the DSC mask. It's 0, 1 or 2. > So, if the split_role is SOLO and hweight is 2, we get exactly your > condition. > num_intf is 1 in this case as only single interface is used. But even 4 dsc encoders going to 2 interfaces its DSC merge. So assuming num_intf as 1 always is not right. Thats why I suggested a generalized confition like above. > Does that sound correct? > >> return true; >> else >> return false; >> } >> >> if (!dpu_encoder_get_dsc_merge_info() && other conditions listed above) >> return BLEND_3D_H_ROW_INT; >> else >> BLEND_3D_NONE; >>> >>> >>>> >>>> All that you have to do is in query whether DSC merge is used from >>>> the topology. You can do it in multiple ways: >>>> >>>> 1) Either query this from the encoder >>>> 2) Store a bool "dsc_merge" in the intf_cfg >>>> >>> >>> > >
On 19/02/2022 00:29, Abhinav Kumar wrote: > > > On 2/18/2022 1:21 PM, Dmitry Baryshkov wrote: >> On 18/02/2022 23:46, Abhinav Kumar wrote: >>> >>> >>> On 2/16/2022 11:12 PM, Dmitry Baryshkov wrote: >>>> On 17/02/2022 09:33, Abhinav Kumar wrote: >>>>> >>>>> >>>>> On 2/16/2022 10:10 PM, Vinod Koul wrote: >>>>>> On 16-02-22, 19:11, Abhinav Kumar wrote: >>>>>>> >>>>>>> >>>>>>> On 2/10/2022 2:34 AM, Vinod Koul wrote: >>>>>>>> We cannot enable mode_3d when we are using the DSC. So pass >>>>>>>> configuration to detect DSC is enabled and not enable mode_3d >>>>>>>> when we are using DSC >>>>>>>> >>>>>>>> We add a helper dpu_encoder_helper_get_dsc() to detect dsc >>>>>>>> enabled and pass this to .setup_intf_cfg() >>>>>>>> >>>>>>>> Signed-off-by: Vinod Koul <vkoul@kernel.org> >>>>>>> >>>>>>> We should not use 3D mux only when we use DSC merge topology. >>>>>>> I agree that today we use only 2-2-1 topology for DSC which means >>>>>>> its using >>>>>>> DSC merge. >>>>>>> >>>>>>> But generalizing that 3D mux should not be used for DSC is not >>>>>>> right. >>>>>>> >>>>>>> You can detect DSC merge by checking if there are two encoders >>>>>>> and one >>>>>>> interface in the topology and if so, you can disable 3D mux. >>>>>> >>>>>> Right now with DSC we disable that as suggested by Dmitry last time. >>>>>> Whenever we introduce merge we should revisit this, for now this >>>>>> should >>>>>> suffice >>>>>> >>>>> >>>>> Sorry I didnt follow. >>>>> >>>>> The topology which you are supporting today IS DSC merge 2-2-1. I >>>>> didnt get what you mean by "whenever we introduce". >>>>> >>>>> I didnt follow Dmitry's comment either. >>>>> >>>>> "anybody adding support for SDE_RM_TOPOLOGY_DUALPIPE_3DMERGE_DSC >>>>> handle this." >>>>> >>>>> 3D mux shouldnt be used when DSC merge is used. >>>>> >>>>> The topology Dmitry is referring to will not use DSC merge but you >>>>> are using it here and thats why you had to make this patch in the >>>>> first place. So I am not sure why would someone who uses 3D merge >>>>> topology worry about DSC merge. Your patch is the one which deals >>>>> with the topology in question. >>>>> >>>>> What I am suggesting is a small but necessary improvement to this >>>>> patch. >>>> >>>> It seems that we can replace this patch by changing >>>> dpu_encoder_helper_get_3d_blend_mode() to contain the following >>>> condition (instead of the one present there). Does the following >>>> seem correct to you: >>>> >>>> static inline enum dpu_3d_blend_mode >>>> dpu_encoder_helper_get_3d_blend_mode( >>>> struct dpu_encoder_phys *phys_enc) >>>> { >>>> struct dpu_crtc_state *dpu_cstate; >>>> >>>> if (!phys_enc || phys_enc->enable_state == DPU_ENC_DISABLING) >>>> return BLEND_3D_NONE; >>>> >>>> dpu_cstate = to_dpu_crtc_state(phys_enc->parent->crtc->state); >>>> >>>> + /* Use merge_3d unless DSCMERGE topology is used */ >>>> if (phys_enc->split_role == ENC_ROLE_SOLO && >>>> + hweight(dpu_encoder_helper_get_dsc(phys_enc)) != 1 && >> >> Yes, the correct should be: >> hweight(...) == 2 >> >>>> dpu_cstate->num_mixers == CRTC_DUAL_MIXERS) >>>> return BLEND_3D_H_ROW_INT; >>>> >>>> return BLEND_3D_NONE; >>>> } >>> >>> This will not be enough. To detect whether DSC merge is enabled you >>> need to query the topology. The above condition only checks if DSC is >>> enabled not DSC merge. >>> >>> So the above function can be modified to use a helper like below >>> instead of the hweight. >>> >>> bool dpu_encoder_get_dsc_merge_info(struct dpu_encoder_virt *dpu_enc) >>> { >>> struct msm_display_topology topology = {0}; >>> >>> topology = dpu_encoder_get_topology(...); >>> >>> if (topology.num_dsc > topology.num_intf) >> >> num_intf is 1 or 2. If it's one, the split_role is SOLO >> hweight would return a num of bits in the DSC mask. It's 0, 1 or 2. >> So, if the split_role is SOLO and hweight is 2, we get exactly your >> condition. >> > num_intf is 1 in this case as only single interface is used. But even 4 > dsc encoders going to 2 interfaces its DSC merge. So assuming num_intf > as 1 always is not right. Thats why I suggested a generalized confition > like above. Ah, quadpipe. Yes, then I was incorrect. > >> Does that sound correct? >> >>> return true; >>> else >>> return false; >>> } >>> >>> if (!dpu_encoder_get_dsc_merge_info() && other conditions listed above) >>> return BLEND_3D_H_ROW_INT; >>> else >>> BLEND_3D_NONE; >>>> >>>> >>>>> >>>>> All that you have to do is in query whether DSC merge is used from >>>>> the topology. You can do it in multiple ways: >>>>> >>>>> 1) Either query this from the encoder >>>>> 2) Store a bool "dsc_merge" in the intf_cfg >>>>> >>>> >>>> >> >>
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c index 34a6940d12c5..ed37a4c21596 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c @@ -70,6 +70,10 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg( intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_CMD; intf_cfg.stream_sel = cmd_enc->stream_sel; intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc); + intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc); + if (intf_cfg.dsc) + intf_cfg.mode_3d = 0; + ctl->ops.setup_intf_cfg(ctl, &intf_cfg); } diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c index ddd9d89cd456..218009855fca 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c @@ -284,6 +284,10 @@ static void dpu_encoder_phys_vid_setup_timing_engine( intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_VID; intf_cfg.stream_sel = 0; /* Don't care value for video mode */ intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc); + intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc); + if (intf_cfg.dsc) + intf_cfg.mode_3d = 0; + if (phys_enc->hw_pp->merge_3d) intf_cfg.merge_3d = phys_enc->hw_pp->merge_3d->idx; diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c index 49659165cea8..6d5268b7da90 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c @@ -536,7 +536,12 @@ static void dpu_hw_ctl_intf_cfg(struct dpu_hw_ctl *ctx, intf_cfg |= (cfg->intf & 0xF) << 4; - if (cfg->mode_3d) { + /* In DSC we can't set merge, so check for dsc and complain */ + if (cfg->mode_3d && cfg->dsc) + pr_err("DPU1: DSC and Merge 3D both are set!! it may not work\n"); + + /* set merge only when dsc is not set */ + if (cfg->mode_3d && !cfg->dsc) { intf_cfg |= BIT(19); intf_cfg |= (cfg->mode_3d - 0x1) << 20; }
We cannot enable mode_3d when we are using the DSC. So pass configuration to detect DSC is enabled and not enable mode_3d when we are using DSC We add a helper dpu_encoder_helper_get_dsc() to detect dsc enabled and pass this to .setup_intf_cfg() Signed-off-by: Vinod Koul <vkoul@kernel.org> --- drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c | 4 ++++ drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 4 ++++ drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c | 7 ++++++- 3 files changed, 14 insertions(+), 1 deletion(-)