deleted file mode 100644
@@ -1,87 +0,0 @@
-QCOM GSBI (General Serial Bus Interface) Driver
-
-The GSBI controller is modeled as a node with zero or more child nodes, each
-representing a serial sub-node device that is mux'd as part of the GSBI
-configuration settings. The mode setting will govern the input/output mode of
-the 4 GSBI IOs.
-
-Required properties:
-- compatible: Should contain "qcom,gsbi-v1.0.0"
-- cell-index: Should contain the GSBI index
-- reg: Address range for GSBI registers
-- clocks: required clock
-- clock-names: must contain "iface" entry
-- qcom,mode : indicates MUX value for configuration of the serial interface.
- Please reference dt-bindings/soc/qcom,gsbi.h for valid mux values.
-
-Optional properties:
-- qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference
- dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values.
-- syscon-tcsr: indicates phandle of TCSR syscon node. Required if child uses
- dma.
-
-Required properties if child node exists:
-- #address-cells: Must be 1
-- #size-cells: Must be 1
-- ranges: Must be present
-
-Properties for children:
-
-A GSBI controller node can contain 0 or more child nodes representing serial
-devices. These serial devices can be a QCOM UART, I2C controller, spi
-controller, or some combination of aforementioned devices.
-
-See the following for child node definitions:
-Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
-Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
-Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
-
-Example for APQ8064:
-
-#include <dt-bindings/soc/qcom,gsbi.h>
-
- gsbi4@16300000 {
- compatible = "qcom,gsbi-v1.0.0";
- cell-index = <4>;
- reg = <0x16300000 0x100>;
- clocks = <&gcc GSBI4_H_CLK>;
- clock-names = "iface";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- qcom,mode = <GSBI_PROT_I2C_UART>;
- qcom,crci = <GSBI_CRCI_QUP>;
-
- syscon-tcsr = <&tcsr>;
-
- /* child nodes go under here */
-
- i2c_qup4: i2c@16380000 {
- compatible = "qcom,i2c-qup-v1.1.1";
- reg = <0x16380000 0x1000>;
- interrupts = <0 153 0>;
-
- clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
- clock-names = "core", "iface";
-
- clock-frequency = <200000>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- };
-
- uart4: serial@16340000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x16340000 0x1000>,
- <0x16300000 0x1000>;
- interrupts = <0 152 0x0>;
- clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
- clock-names = "core", "iface";
- };
- };
-
- tcsr: syscon@1a400000 {
- compatible = "qcom,apq8064-tcsr", "syscon";
- reg = <0x1a400000 0x100>;
- };
new file mode 100644
@@ -0,0 +1,132 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,gsbi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm General Serial Bus Interface (GSBI)
+
+maintainers:
+ - Andy Gross <agross@kernel.org>
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ The GSBI controller is modeled as a node with zero or more child nodes, each
+ representing a serial sub-node device that is mux'd as part of the GSBI
+ configuration settings. The mode setting will govern the input/output mode
+ of the 4 GSBI IOs.
+
+ A GSBI controller node can contain 0 or more child nodes representing serial
+ devices. These serial devices can be a QCOM UART, I2C controller, spi
+ controller, or some combination of aforementioned devices.
+
+properties:
+ compatible:
+ const: qcom,gsbi-v1.0.0
+
+ '#address-cells':
+ const: 1
+
+ cell-index:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The GSBI index.
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ const: iface
+
+ qcom,crci:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ CRCI MUX value for QUP CRCI ports. Please reference
+ include/dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values.
+
+ qcom,mode:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ MUX value for configuration of the serial interface. Please reference
+ include/dt-bindings/soc/qcom,gsbi.h for valid mux values.
+
+ '#size-cells':
+ const: 1
+
+ syscon-tcsr:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ Phandle of TCSR syscon node.Required if child uses dma.
+
+ ranges: true
+
+ reg:
+ maxItems: 1
+
+patternProperties:
+ "spi@[0-9a-f]+$":
+ type: object
+ $ref: /schemas/spi/qcom,spi-qup.yaml#
+
+ "i2c@[0-9a-f]+$":
+ type: object
+ $ref: /schemas/i2c/qcom,i2c-qup.yaml#
+
+ "serial@[0-9a-f]+$":
+ type: object
+ $ref: /schemas/serial/qcom,msm-uartdm.yaml#
+
+required:
+ - compatible
+ - cell-index
+ - clocks
+ - clock-names
+ - qcom,mode
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-msm8960.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/soc/qcom,gsbi.h>
+
+ gsbi@12440000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ reg = <0x12440000 0x100>;
+ cell-index = <1>;
+ clocks = <&gcc GSBI1_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ syscon-tcsr = <&tcsr>;
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+
+ serial@12450000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x12450000 0x100>,
+ <0x12400000 0x03>;
+ interrupts = <0 193 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
+ clock-names = "core", "iface";
+ };
+
+ i2c@12460000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x12460000 0x1000>;
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-1 = <&i2c1_pins_sleep>;
+ pinctrl-names = "default", "sleep";
+ interrupts = <0 194 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+ clock-names = "core", "iface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled"; /* UART chosen */
+ };
+ };