@@ -35,7 +35,7 @@ sdhci@f9824900 {
};
sdhci@f98a4900 {
- cd-gpios = <&msmgpio 62 0x1>;
+ cd-gpios = <&tlmm 62 0x1>;
pinctrl-names = "default";
pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
bus-width = <4>;
@@ -51,7 +51,7 @@ volume-up {
vibrator {
compatible = "gpio-vibrator";
- enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
vcc-supply = <&pm8941_l18>;
};
@@ -229,7 +229,7 @@ vreg_wlan: wlan-regulator {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- gpio = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
+ gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
@@ -482,9 +482,9 @@ bluetooth {
pinctrl-names = "default";
pinctrl-0 = <&bt_pin>;
- host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
- device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
};
};
@@ -522,7 +522,7 @@ i2c@f9968000 {
mpu6515@68 {
compatible = "invensense,mpu6515";
reg = <0x68>;
- interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&tlmm 73 IRQ_TYPE_EDGE_FALLING>;
vddio-supply = <&pm8941_lvs1>;
pinctrl-names = "default";
@@ -538,7 +538,7 @@ i2c-gate {
ak8963@f {
compatible = "asahi-kasei,ak8963";
reg = <0x0f>;
- gpios = <&msmgpio 67 0>;
+ gpios = <&tlmm 67 0>;
vid-supply = <&pm8941_lvs1>;
vdd-supply = <&pm8941_l17>;
};
@@ -577,7 +577,7 @@ fuelgauge: max17048@36 {
maxim,double-soc;
maxim,rcomp = /bits/ 8 <0x4d>;
- interrupt-parent = <&msmgpio>;
+ interrupt-parent = <&tlmm>;
interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
@@ -600,7 +600,7 @@ synaptics@70 {
compatible = "syna,rmi4-i2c";
reg = <0x70>;
- interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&tlmm 5 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&pm8941_l22>;
vio-supply = <&pm8941_lvs3>;
@@ -632,7 +632,7 @@ i2c@f9925000 {
avago_apds993@39 {
compatible = "avago,apds9930";
reg = <0x39>;
- interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&pm8941_l17>;
vddio-supply = <&pm8941_lvs1>;
led-max-microamp = <100000>;
@@ -215,8 +215,8 @@ i2c-gpio-touchkey {
compatible = "i2c-gpio";
#address-cells = <1>;
#size-cells = <0>;
- sda-gpios = <&msmgpio 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- scl-gpios = <&msmgpio 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
pinctrl-names = "default";
pinctrl-0 = <&i2c_touchkey_pins>;
@@ -240,8 +240,8 @@ i2c-gpio-led {
compatible = "i2c-gpio";
#address-cells = <1>;
#size-cells = <0>;
- scl-gpios = <&msmgpio 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&msmgpio 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
pinctrl-names = "default";
pinctrl-0 = <&i2c_led_gpioex_pins>;
@@ -259,7 +259,7 @@ gpio_expander: gpio@20 {
pinctrl-names = "default";
pinctrl-0 = <&gpioex_pin>;
- reset-gpios = <&msmgpio 145 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
};
led-controller@30 {
@@ -339,9 +339,9 @@ bluetooth {
max-speed = <3000000>;
pinctrl-names = "default";
pinctrl-0 = <&bt_pins>;
- device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
- interrupt-parent = <&msmgpio>;
+ interrupt-parent = <&tlmm>;
interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "host-wakeup";
};
@@ -563,7 +563,7 @@ sdhci@f9864900 {
*/
pinctrl-names = "default";
pinctrl-0 = <&sdhc2_pin_a /* &sdhc2_cd_pin */>;
- // cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ // cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
};
sdhci@f98a4900 {
@@ -587,7 +587,7 @@ wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
- interrupt-parent = <&msmgpio>;
+ interrupt-parent = <&tlmm>;
interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "host-wake";
@@ -818,7 +818,7 @@ panel: panel@0 {
vddr-supply = <&vreg_panel>;
reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
- te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>;
+ te-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
port {
panel_in: endpoint {
@@ -280,7 +280,7 @@ sdhci@f98a4900 {
vmmc-supply = <&pm8941_l21>;
vqmmc-supply = <&pm8941_l13>;
- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
@@ -305,7 +305,7 @@ sdhci@f98a4900 {
vmmc-supply = <&pm8941_l21>;
vqmmc-supply = <&pm8941_l13>;
- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
@@ -331,7 +331,7 @@ synaptics@2c {
compatible = "syna,rmi4-i2c";
reg = <0x2c>;
- interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
#address-cells = <1>;
#size-cells = <0>;
@@ -239,7 +239,7 @@ vreg_bl_vddio: lcd-backlight-vddio {
regulator-min-microvolt = <3150000>;
regulator-max-microvolt = <3150000>;
- gpio = <&msmgpio 69 0>;
+ gpio = <&tlmm 69 0>;
enable-active-high;
vin-supply = <&pm8941_s3>;
@@ -323,7 +323,7 @@ sdhci@f98a4900 {
vmmc-supply = <&pm8941_l21>;
vqmmc-supply = <&pm8941_l13>;
- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
@@ -351,8 +351,8 @@ bluetooth {
<&bt_dev_wake_pin>,
<&bt_reg_on_pin>;
- host-wakeup-gpios = <&msmgpio 95 GPIO_ACTIVE_HIGH>;
- device-wakeup-gpios = <&msmgpio 96 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
};
};
@@ -566,7 +566,7 @@ synaptics@2c {
compatible = "syna,rmi4-i2c";
reg = <0x2c>;
- interrupt-parent = <&msmgpio>;
+ interrupt-parent = <&tlmm>;
interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
#address-cells = <1>;
@@ -953,11 +953,11 @@ wifi {
};
};
- msmgpio: pinctrl@fd510000 {
+ tlmm: pinctrl@fd510000 {
compatible = "qcom,msm8974-pinctrl";
reg = <0xfd510000 0x4000>;
gpio-controller;
- gpio-ranges = <&msmgpio 0 0 146>;
+ gpio-ranges = <&tlmm 0 0 146>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
Rename the label to match new the style used in newer DTs. Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> --- .../arm/boot/dts/qcom-apq8074-dragonboard.dts | 2 +- .../boot/dts/qcom-msm8974-fairphone-fp2.dts | 2 +- .../qcom-msm8974-lge-nexus5-hammerhead.dts | 18 ++++++++--------- .../boot/dts/qcom-msm8974-samsung-klte.dts | 20 +++++++++---------- .../qcom-msm8974-sony-xperia-rhine-amami.dts | 2 +- .../qcom-msm8974-sony-xperia-rhine-honami.dts | 4 ++-- ...com-msm8974-sony-xperia-shinano-castor.dts | 10 +++++----- arch/arm/boot/dts/qcom-msm8974.dtsi | 4 ++-- 8 files changed, 31 insertions(+), 31 deletions(-)