diff mbox series

[v4,3/5] arm64: dts: qcom: Add PM6125 PMIC

Message ID 20220926190148.283805-4-marijn.suijten@somainline.org (mailing list archive)
State Accepted
Headers show
Series Add Qcom PM6125 PMIC and use in Sony Xperia Seine PDX201 | expand

Commit Message

Marijn Suijten Sept. 26, 2022, 7:01 p.m. UTC 
This PMIC is commonly used on boards with an SM6125 SoC and looks very
similar in layout to the PM6150.

Downstream declares more nodes to be available, but these have been
omitted from this patch: the pwm/lpg block is unused on my reference
device making it impossible to test/validate, and the spmi-clkdiv does
not have a single device-tree binding using this driver yet, hence
inclusion is better postponed until ie. audio which uses these clocks is
brought up.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/pm6125.dtsi | 154 +++++++++++++++++++++++++++
 1 file changed, 154 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pm6125.dtsi
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/pm6125.dtsi b/arch/arm64/boot/dts/qcom/pm6125.dtsi
new file mode 100644
index 000000000000..1c8ccda26ffb
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm6125.dtsi
@@ -0,0 +1,154 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm6125-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm6125_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmic@0 {
+		compatible = "qcom,pm6125", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm6125_pon: pon@800 {
+			compatible = "qcom,pm8998-pon";
+			reg = <0x800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
+
+			pon_pwrkey: pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				linux,code = <KEY_POWER>;
+				bias-pull-up;
+				status = "disabled";
+			};
+
+			pon_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		pm6125_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm6125_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm6125_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#io-channel-cells = <1>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			vph-pwr@83 {
+				reg = <ADC5_VPH_PWR>;
+				qcom,pre-scaling = <1 3>;
+			};
+
+			vcoin@85 {
+				reg = <ADC5_VCOIN>;
+				qcom,pre-scaling = <1 3>;
+			};
+
+			xo-therm@4c {
+				reg = <ADC5_XO_THERM_100K_PU>;
+				qcom,pre-scaling = <1 1>;
+				qcom,hw-settle-time = <200>;
+				qcom,ratiometric;
+			};
+		};
+
+		pm6125_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#thermal-sensor-cells = <1>;
+			status = "disabled";
+		};
+
+		pm6125_rtc: rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		pm6125_gpio: gpio@c000 {
+			compatible = "qcom,pm6125-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm6125_gpio 0 0 9>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pm6125", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+	};
+};