@@ -8,10 +8,15 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
+/* (Sadly) this PMIC can be configured to be at different SIDs */
+#ifndef PMK8350_SID
+ #define PMK8350_SID 0
+#endif
+
&spmi_bus {
- pmk8350: pmic@0 {
+ pmk8350: pmic@PMK8350_SID {
compatible = "qcom,pmk8350", "qcom,spmi-pmic";
- reg = <0x0 SPMI_USID>;
+ reg = <PMK8350_SID SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
@@ -21,14 +26,14 @@ pmk8350_pon: pon@1300 {
pon_pwrkey: pwrkey {
compatible = "qcom,pmk8350-pwrkey";
- interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+ interrupts = <PMK8350_SID 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
linux,code = <KEY_POWER>;
status = "disabled";
};
pon_resin: resin {
compatible = "qcom,pmk8350-resin";
- interrupts = <0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
+ interrupts = <PMK8350_SID 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
status = "disabled";
};
};
@@ -38,14 +43,14 @@ pmk8350_vadc: adc@3100 {
reg = <0x3100>;
#address-cells = <1>;
#size-cells = <0>;
- interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <PMK8350_SID 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
#io-channel-cells = <1>;
};
pmk8350_adc_tm: adc-tm@3400 {
compatible = "qcom,adc-tm7";
reg = <0x3400>;
- interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <PMK8350_SID 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;
#thermal-sensor-cells = <1>;
@@ -56,7 +61,7 @@ pmk8350_rtc: rtc@6100 {
compatible = "qcom,pmk8350-rtc";
reg = <0x6100>, <0x6200>;
reg-names = "rtc", "alarm";
- interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <PMK8350_SID 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
};
PMK8350 is shipped on SID6 with some SoCs, for example with SM6375. Add some preprocessor logic to allow changing the SID in cases like this. While I am not in favour of adding #if's into the device tree, this is the least messy way to handle this. If one isn't specified, it will default to 0 (as it has been previously). Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/pmk8350.dtsi | 19 ++++++++++++------- 1 file changed, 12 insertions(+), 7 deletions(-)