| Message ID | 20221116103146.2556846-10-abel.vesa@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add base device tree files for SM8550 | expand |
On 16/11/2022 11:31, Abel Vesa wrote: > From: Neil Armstrong <neil.armstrong@linaro.org> > > Add nodes for PMR735d in separate dtsi file. > > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > arch/arm64/boot/dts/qcom/pmr735d.dtsi | 104 ++++++++++++++++++++++++++ > 1 file changed, 104 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/pmr735d.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/pmr735d.dtsi b/arch/arm64/boot/dts/qcom/pmr735d.dtsi > new file mode 100644 > index 000000000000..41fb664a10b3 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/pmr735d.dtsi > @@ -0,0 +1,104 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2022, Linaro Limited > + */ > + > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +/ { > + thermal-zones { > + pmr735d-k-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + > + thermal-sensors = <&pmr735d_k_temp_alarm>; > + > + trips { > + trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; > + }; > + }; > + }; > + > + pmr735d-l-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + > + thermal-sensors = <&pmr735d_l_temp_alarm>; > + > + trips { > + trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; > + }; > + }; > + }; > + }; > +}; > + > + > +&spmi_bus { > + pmr735d_k: pmic@a { > + compatible = "qcom,pmr735d", "qcom,spmi-pmic"; > + reg = <0xa SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pmr735d_k_temp_alarm: temp-alarm@a00 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0xa00>; > + interrupts = <0xa 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > + > + pmr735d_k_gpios: gpio@8800 { > + compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmr735d_k_gpios 0 0 2>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > + > + pmr735d_l: pmic@b { > + compatible = "qcom,pmr735d", "qcom,spmi-pmic"; > + reg = <0xb SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pmr735d_l_temp_alarm: temp-alarm@a00 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0xa00>; > + interrupts = <0xb 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > + > + pmr735d_l_gpios: gpio@8800 { > + compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmr735d_l_gpios 0 0 2>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > +};
diff --git a/arch/arm64/boot/dts/qcom/pmr735d.dtsi b/arch/arm64/boot/dts/qcom/pmr735d.dtsi new file mode 100644 index 000000000000..41fb664a10b3 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmr735d.dtsi @@ -0,0 +1,104 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2022, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +/ { + thermal-zones { + pmr735d-k-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + + thermal-sensors = <&pmr735d_k_temp_alarm>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + }; + }; + + pmr735d-l-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + + thermal-sensors = <&pmr735d_l_temp_alarm>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + }; + }; + }; +}; + + +&spmi_bus { + pmr735d_k: pmic@a { + compatible = "qcom,pmr735d", "qcom,spmi-pmic"; + reg = <0xa SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmr735d_k_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0xa 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pmr735d_k_gpios: gpio@8800 { + compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmr735d_k_gpios 0 0 2>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmr735d_l: pmic@b { + compatible = "qcom,pmr735d", "qcom,spmi-pmic"; + reg = <0xb SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmr735d_l_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0xb 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pmr735d_l_gpios: gpio@8800 { + compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmr735d_l_gpios 0 0 2>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +};