@@ -1064,6 +1064,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-msm8974-sony-xperia-rhine-amami.dtb \
qcom-msm8974-sony-xperia-rhine-honami.dtb \
qcom-msm8974pro-fairphone-fp2.dtb \
+ qcom-msm8974pro-oneplus-bacon.dtb \
qcom-msm8974pro-samsung-klte.dtb \
qcom-msm8974pro-sony-xperia-shinano-castor.dtb \
qcom-mdm9615-wp8548-mangoh-green.dtb \
new file mode 100644
@@ -0,0 +1,417 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+ model = "OnePlus One";
+ compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974";
+ chassis-type = "handset";
+ qcom,msm-id = <194 0x10000>;
+ qcom,board-id = <8 0>;
+
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&blsp1_i2c1 {
+ status = "okay";
+
+ fuel-gauge@55 {
+ compatible = "ti,bq27541";
+ reg = <0x55>;
+ power-supplies = <&bq24196_charger>;
+ };
+};
+
+&blsp1_i2c2 {
+ status = "okay";
+
+ rmi4-i2c-dev@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+
+ syna,startup-delay-ms = <100>;
+
+ interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_default_state>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
+ /*
+ * Touchscreen size is 2040x1080, y-values between
+ * 1920-2040 are used for touchkey (menu, home & back).
+ * For now clip it off so we don't get touch events
+ * outside of the display area.
+ */
+ syna,clip-y-high = <1920>;
+ };
+ };
+};
+
+&blsp1_i2c6 {
+ status = "okay";
+
+ bq24196_charger: charger@6b {
+ compatible = "ti,bq24196";
+ reg = <0x6b>;
+ interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ omit-battery-class;
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&gcc {
+ compatible = "qcom,gcc-msm8974pro-ac";
+};
+
+&pm8941_coincell {
+ qcom,rset-ohms = <800>;
+ qcom,vset-millivolts = <3200>;
+
+ status = "okay";
+};
+
+&pronto {
+ vddmx-supply = <&pm8841_s1>;
+ vddcx-supply = <&pm8841_s2>;
+ vddpx-supply = <&pm8941_s3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;
+
+ status = "okay";
+
+ iris {
+ vddxo-supply = <&pm8941_l6>;
+ vddrfa-supply = <&pm8941_l11>;
+ vddpa-supply = <&pm8941_l19>;
+ vdddig-supply = <&pm8941_s3>;
+ };
+
+ smd-edge {
+ qcom,remote-pid = <4>;
+ label = "pronto";
+
+ wcnss {
+ status = "okay";
+ };
+ };
+};
+
+&remoteproc_adsp {
+ cx-supply = <&pm8841_s2>;
+
+ status = "okay";
+};
+
+&rpm_requests {
+ regulators-0 {
+ compatible = "qcom,rpm-pm8841-regulators";
+
+ pm8841_s1: s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ pm8841_s2: s2 {
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ };
+
+ pm8841_s3: s3 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,rpm-pm8941-regulators";
+
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ pm8941_s1: s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ pm8941_s2: s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+
+ regulator-boot-on;
+ };
+
+ pm8941_s3: s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-system-load = <154000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ };
+
+ pm8941_l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ pm8941_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8941_l3: l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pm8941_l4: l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pm8941_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8941_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ pm8941_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ pm8941_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8941_l9: l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8941_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8941_l11: l11 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ pm8941_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ };
+
+ pm8941_l13: l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ pm8941_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8941_l15: l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pm8941_l16: l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ pm8941_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pm8941_l18: l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pm8941_l19: l19 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <3350000>;
+ };
+
+ pm8941_l20: l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ regulator-boot-on;
+ };
+
+ pm8941_l21: l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ pm8941_l22: l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-allow-set-load;
+ };
+
+ pm8941_l23: l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pm8941_l24: l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
+ };
+
+ pm8941_lvs3: lvs3 {};
+ };
+};
+
+&sdhc_1 {
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_on>;
+ pinctrl-1 = <&sdc1_off>;
+
+ status = "okay";
+};
+
+&tlmm {
+ sdc1_on: sdc1-on-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ cmd-data-pins {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <4>;
+ bias-pull-up;
+ };
+ };
+
+ touch_default_state: touch-default-state {
+ int-pins {
+ pins = "gpio61";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
+
+ reset-pins {
+ pins = "gpio60";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ wcnss_pin_a: wcnss-pin-active-state {
+ wlan-pins {
+ pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+ function = "wlan";
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+
+ bt-pins {
+ pins = "gpio35", "gpio43", "gpio44";
+ function = "bt";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+};
+
+&usb {
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ status = "okay";
+};
+
+&usb_hs1_phy {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};