| Message ID | 20230113041132.4189268-4-quic_bjorande@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | soc: qcom: Introduce PMIC GLINK | expand |
On Thu, Jan 12, 2023 at 10:13 PM Bjorn Andersson <quic_bjorande@quicinc.com> wrote: > > From: Bjorn Andersson <bjorn.andersson@linaro.org> > > With the PMIC GLINK service, the host OS subscribes to USB-C altmode > messages, which are sent by the firmware to notify the host OS about > state updates and HPD interrupts. > > The pmic_glink_altmode driver registers for these notifications and > propagates the notifications as typec_mux, typec_switch and DRM OOB > notifications as necessary to implement DisplayPort altmode support. > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> > --- > > Changes since v1: > - None > > Johan reported a NULL pointer dereference in > drm_kms_helper_hotplug_event() for HPD event being reported while the > MSM DRM driver is still being initalized, a separate fix has been sent > in hope to remidy this race condition in the MSM driver. > > drivers/soc/qcom/Makefile | 1 + > drivers/soc/qcom/pmic_glink_altmode.c | 477 ++++++++++++++++++++++++++ > 2 files changed, 478 insertions(+) > create mode 100644 drivers/soc/qcom/pmic_glink_altmode.c > > diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile > index 29cccac472f3..f30552bf4da7 100644 > --- a/drivers/soc/qcom/Makefile > +++ b/drivers/soc/qcom/Makefile > @@ -10,6 +10,7 @@ obj-$(CONFIG_QCOM_MDT_LOADER) += mdt_loader.o > obj-$(CONFIG_QCOM_OCMEM) += ocmem.o > obj-$(CONFIG_QCOM_PDR_HELPERS) += pdr_interface.o > obj-$(CONFIG_QCOM_PMIC_GLINK) += pmic_glink.o > +obj-$(CONFIG_QCOM_PMIC_GLINK) += pmic_glink_altmode.o > obj-$(CONFIG_QCOM_QMI_HELPERS) += qmi_helpers.o > qmi_helpers-y += qmi_encdec.o qmi_interface.o > obj-$(CONFIG_QCOM_RAMP_CTRL) += ramp_controller.o > diff --git a/drivers/soc/qcom/pmic_glink_altmode.c b/drivers/soc/qcom/pmic_glink_altmode.c > new file mode 100644 > index 000000000000..8d2d563cb756 > --- /dev/null > +++ b/drivers/soc/qcom/pmic_glink_altmode.c > @@ -0,0 +1,477 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved. > + * Copyright (c) 2022, Linaro Ltd > + */ > +#include <linux/auxiliary_bus.h> > +#include <linux/module.h> > +#include <linux/of_device.h> > +#include <linux/mutex.h> > +#include <linux/property.h> > +#include <linux/soc/qcom/pdr.h> > +#include <drm/drm_bridge.h> > + > +#include <linux/usb/typec_altmode.h> > +#include <linux/usb/typec_dp.h> > +#include <linux/usb/typec_mux.h> > + > +#include <linux/soc/qcom/pmic_glink.h> > + > +#define PMIC_GLINK_MAX_PORTS 2 > + > +#define USBC_SC8180X_NOTIFY_IND 0x13 > +#define USBC_CMD_WRITE_REQ 0x15 > +#define USBC_NOTIFY_IND 0x16 > + > +#define ALTMODE_PAN_EN 0x10 > +#define ALTMODE_PAN_ACK 0x11 > + > +struct usbc_write_req { > + struct pmic_glink_hdr hdr; > + __le32 cmd; > + __le32 arg; > + __le32 reserved; > +}; > + > +#define NOTIFY_PAYLOAD_SIZE 16 > +struct usbc_notify { > + struct pmic_glink_hdr hdr; > + char payload[NOTIFY_PAYLOAD_SIZE]; > + u32 reserved; > +}; > + > +struct usbc_sc8180x_notify { > + struct pmic_glink_hdr hdr; > + __le32 notification; > + __le32 reserved[2]; > +}; > + > +enum pmic_glink_altmode_pin_assignment { > + DPAM_HPD_OUT, > + DPAM_HPD_A, > + DPAM_HPD_B, > + DPAM_HPD_C, > + DPAM_HPD_D, > + DPAM_HPD_E, > + DPAM_HPD_F, > +}; > + > +struct pmic_glink_altmode; > + > +#define work_to_altmode_port(w) container_of((w), struct pmic_glink_altmode_port, work) > + > +struct pmic_glink_altmode_port { > + struct pmic_glink_altmode *altmode; > + unsigned int index; > + > + struct typec_switch *typec_switch; > + struct typec_mux *typec_mux; > + struct typec_mux_state state; > + struct typec_altmode dp_alt; > + > + struct work_struct work; > + > + struct drm_bridge bridge; > + > + enum typec_orientation orientation; > + u16 svid; > + u8 dp_data; > + u8 mode; > + u8 hpd_state; > + u8 hpd_irq; > +}; > + > +#define work_to_altmode(w) container_of((w), struct pmic_glink_altmode, enable_work) > + > +struct pmic_glink_altmode { > + struct device *dev; > + > + unsigned int owner_id; > + > + /* To synchronize WRITE_REQ acks */ > + struct mutex lock; > + > + struct completion pan_ack; > + struct pmic_glink_client *client; > + > + struct work_struct enable_work; > + > + struct pmic_glink_altmode_port ports[PMIC_GLINK_MAX_PORTS]; > +}; > + > +static int pmic_glink_altmode_request(struct pmic_glink_altmode *altmode, u32 cmd, u32 arg) > +{ > + struct usbc_write_req req = {}; > + unsigned long left; > + int ret; > + > + /* > + * The USBC_CMD_WRITE_REQ ack doesn't identify the request, so wait for > + * one ack at a time. > + */ > + mutex_lock(&altmode->lock); > + > + req.hdr.owner = cpu_to_le32(altmode->owner_id); > + req.hdr.type = cpu_to_le32(PMIC_GLINK_REQ_RESP); > + req.hdr.opcode = cpu_to_le32(USBC_CMD_WRITE_REQ); > + req.cmd = cpu_to_le32(cmd); > + req.arg = cpu_to_le32(arg); > + > + ret = pmic_glink_send(altmode->client, &req, sizeof(req)); > + if (ret) { > + dev_err(altmode->dev, "failed to send altmode request: %#x (%d)\n", cmd, ret); > + goto out_unlock; > + } > + > + left = wait_for_completion_timeout(&altmode->pan_ack, 5 * HZ); > + if (!left) { > + dev_err(altmode->dev, "timeout waiting for altmode request ack for: %#x\n", cmd); > + ret = -ETIMEDOUT; > + } > + > +out_unlock: > + mutex_unlock(&altmode->lock); > + return ret; > +} > + > +static void pmic_glink_altmode_enable_dp(struct pmic_glink_altmode *altmode, > + struct pmic_glink_altmode_port *port, > + u8 mode, bool hpd_state, > + bool hpd_irq) > +{ > + struct typec_displayport_data dp_data = {}; > + int ret; > + > + dp_data.status = DP_STATUS_ENABLED; > + if (hpd_state) > + dp_data.status |= DP_STATUS_HPD_STATE; > + if (hpd_irq) > + dp_data.status |= DP_STATUS_IRQ_HPD; > + dp_data.conf = DP_CONF_SET_PIN_ASSIGN(mode); > + > + port->state.alt = &port->dp_alt; > + port->state.data = &dp_data; > + port->state.mode = TYPEC_MODAL_STATE(mode); > + > + ret = typec_mux_set(port->typec_mux, &port->state); > + if (ret) > + dev_err(altmode->dev, "failed to switch mux to DP\n"); > +} > + > +static void pmic_glink_altmode_enable_usb(struct pmic_glink_altmode *altmode, > + struct pmic_glink_altmode_port *port) > +{ > + int ret; > + > + port->state.alt = NULL; > + port->state.data = NULL; > + port->state.mode = TYPEC_STATE_USB; > + > + ret = typec_mux_set(port->typec_mux, &port->state); > + if (ret) > + dev_err(altmode->dev, "failed to switch mux to USB\n"); > +} > + > +static void pmic_glink_altmode_worker(struct work_struct *work) > +{ > + struct pmic_glink_altmode_port *alt_port = work_to_altmode_port(work); > + struct pmic_glink_altmode *altmode = alt_port->altmode; > + > + typec_switch_set(alt_port->typec_switch, alt_port->orientation); > + > + if (alt_port->svid == USB_TYPEC_DP_SID) > + pmic_glink_altmode_enable_dp(altmode, alt_port, alt_port->mode, > + alt_port->hpd_state, alt_port->hpd_irq); > + else > + pmic_glink_altmode_enable_usb(altmode, alt_port); > + > + if (alt_port->hpd_state) > + drm_bridge_hpd_notify(&alt_port->bridge, connector_status_connected); > + else > + drm_bridge_hpd_notify(&alt_port->bridge, connector_status_disconnected); > + > + pmic_glink_altmode_request(altmode, ALTMODE_PAN_ACK, alt_port->index); > +}; > + > +static enum typec_orientation pmic_glink_altmode_orientation(unsigned int orientation) > +{ > + if (orientation == 0) > + return TYPEC_ORIENTATION_NORMAL; > + else if (orientation == 1) > + return TYPEC_ORIENTATION_REVERSE; > + else > + return TYPEC_ORIENTATION_NONE; > +} > + > +#define SC8180X_PORT_MASK 0x000000ff > +#define SC8180X_ORIENTATION_MASK 0x0000ff00 > +#define SC8180X_MUX_MASK 0x00ff0000 > +#define SC8180X_MODE_MASK 0x3f000000 > +#define SC8180X_HPD_STATE_MASK 0x40000000 > +#define SC8180X_HPD_IRQ_MASK 0x80000000 > + > +static void pmic_glink_altmode_sc8180xp_notify(struct pmic_glink_altmode *altmode, > + const void *data, size_t len) > +{ > + struct pmic_glink_altmode_port *alt_port; > + const struct usbc_sc8180x_notify *msg; > + u32 notification; > + u8 orientation; > + u8 hpd_state; > + u8 hpd_irq; > + u16 svid; > + u8 port; > + u8 mode; > + u8 mux; > + > + if (len != sizeof(*msg)) { > + dev_warn(altmode->dev, "invalid length of USBC_NOTIFY indication: %zd\n", len); > + return; > + } > + > + msg = data; > + notification = le32_to_cpu(msg->notification); > + port = FIELD_GET(SC8180X_PORT_MASK, notification); > + orientation = FIELD_GET(SC8180X_ORIENTATION_MASK, notification); > + mux = FIELD_GET(SC8180X_MUX_MASK, notification); > + mode = FIELD_GET(SC8180X_MODE_MASK, notification); > + hpd_state = FIELD_GET(SC8180X_HPD_STATE_MASK, notification); > + hpd_irq = FIELD_GET(SC8180X_HPD_IRQ_MASK, notification); > + The kernel test robot keeps complaining about these FIELD_GET because there is no #include <linux/bitfield.h> > + svid = mux == 2 ? USB_TYPEC_DP_SID : 0; > + > + if (!altmode->ports[port].altmode) { > + dev_dbg(altmode->dev, "notification on undefined port %d\n", port); > + return; > + } > + > + alt_port = &altmode->ports[port]; > + alt_port->orientation = pmic_glink_altmode_orientation(orientation); > + alt_port->svid = mux == 2 ? USB_TYPEC_DP_SID : 0; > + alt_port->mode = mode; > + alt_port->hpd_state = hpd_state; > + alt_port->hpd_irq = hpd_irq; > + schedule_work(&alt_port->work); > +} > + > +#define SC8280XP_DPAM_MASK 0x3f > +#define SC8280XP_HPD_STATE_MASK BIT(6) > +#define SC8280XP_HPD_IRQ_MASK BIT(7) > + > +static void pmic_glink_altmode_sc8280xp_notify(struct pmic_glink_altmode *altmode, > + u16 svid, const void *data, size_t len) > +{ > + struct pmic_glink_altmode_port *alt_port; > + const struct usbc_notify *notify; > + u8 orientation; > + u8 hpd_state; > + u8 hpd_irq; > + u8 mode; > + u8 port; > + > + if (len != sizeof(*notify)) { > + dev_warn(altmode->dev, "invalid length USBC_NOTIFY_IND: %zd\n", > + len); > + return; > + } > + > + notify = data; > + > + port = notify->payload[0]; > + orientation = notify->payload[1]; > + mode = FIELD_GET(SC8280XP_DPAM_MASK, notify->payload[8]) - DPAM_HPD_A; > + hpd_state = FIELD_GET(SC8280XP_HPD_STATE_MASK, notify->payload[8]); > + hpd_irq = FIELD_GET(SC8280XP_HPD_IRQ_MASK, notify->payload[8]); > + > + if (!altmode->ports[port].altmode) { > + dev_dbg(altmode->dev, "notification on undefined port %d\n", port); > + return; > + } > + > + alt_port = &altmode->ports[port]; > + alt_port->orientation = pmic_glink_altmode_orientation(orientation); > + alt_port->svid = svid; > + alt_port->mode = mode; > + alt_port->hpd_state = hpd_state; > + alt_port->hpd_irq = hpd_irq; > + schedule_work(&alt_port->work); > +} > + > +static void pmic_glink_altmode_callback(const void *data, size_t len, void *priv) > +{ > + struct pmic_glink_altmode *altmode = priv; > + const struct pmic_glink_hdr *hdr = data; > + u16 opcode; > + u16 svid; > + > + opcode = le32_to_cpu(hdr->opcode) & 0xff; > + svid = le32_to_cpu(hdr->opcode) >> 16; > + > + switch (opcode) { > + case USBC_CMD_WRITE_REQ: > + complete(&altmode->pan_ack); > + break; > + case USBC_NOTIFY_IND: > + pmic_glink_altmode_sc8280xp_notify(altmode, svid, data, len); > + break; > + case USBC_SC8180X_NOTIFY_IND: > + pmic_glink_altmode_sc8180xp_notify(altmode, data, len); > + break; > + } > +} > + > +static int pmic_glink_altmode_attach(struct drm_bridge *bridge, > + enum drm_bridge_attach_flags flags) > +{ > + return flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR ? 0 : -EINVAL; > +} > + > +static const struct drm_bridge_funcs pmic_glink_altmode_bridge_funcs = { > + .attach = pmic_glink_altmode_attach, > +}; > + > +static void pmic_glink_altmode_put_mux(void *data) > +{ > + typec_mux_put(data); > +} > + > +static void pmic_glink_altmode_put_switch(void *data) > +{ > + typec_switch_put(data); > +} > + > +static void pmic_glink_altmode_enable_worker(struct work_struct *work) > +{ > + struct pmic_glink_altmode *altmode = work_to_altmode(work); > + int ret; > + > + ret = pmic_glink_altmode_request(altmode, ALTMODE_PAN_EN, 0); > + if (ret) > + dev_err(altmode->dev, "failed to request altmode notifications\n"); > +} > + > +static void pmic_glink_altmode_pdr_notify(void *priv, int state) > +{ > + struct pmic_glink_altmode *altmode = priv; > + > + if (state == SERVREG_SERVICE_STATE_UP) > + schedule_work(&altmode->enable_work); > +} > + > +static const struct of_device_id pmic_glink_altmode_of_quirks[] = { > + { .compatible = "qcom,sc8180x-pmic-glink", .data = (void *)PMIC_GLINK_OWNER_USBC }, > + {} > +}; > + > +static int pmic_glink_altmode_probe(struct auxiliary_device *adev, > + const struct auxiliary_device_id *id) > +{ > + struct pmic_glink_altmode_port *alt_port; > + struct pmic_glink_altmode *altmode; > + struct typec_altmode_desc mux_desc = {}; > + const struct of_device_id *match; > + struct fwnode_handle *fwnode; > + struct device *dev = &adev->dev; > + u32 port; > + int ret; > + > + altmode = devm_kzalloc(dev, sizeof(*altmode), GFP_KERNEL); > + if (!altmode) > + return -ENOMEM; > + > + altmode->dev = dev; > + > + match = of_match_device(pmic_glink_altmode_of_quirks, dev->parent); > + if (match) > + altmode->owner_id = (unsigned long)match->data; > + else > + altmode->owner_id = PMIC_GLINK_OWNER_USBC_PAN; > + > + INIT_WORK(&altmode->enable_work, pmic_glink_altmode_enable_worker); > + init_completion(&altmode->pan_ack); > + mutex_init(&altmode->lock); > + > + device_for_each_child_node(dev, fwnode) { > + ret = fwnode_property_read_u32(fwnode, "reg", &port); > + if (ret < 0) { > + dev_err(dev, "missing reg property of %pOFn\n", fwnode); > + return ret; > + } > + > + if (port >= ARRAY_SIZE(altmode->ports)) { > + dev_warn(dev, "invalid connector number, ignoring\n"); > + continue; > + } > + > + if (altmode->ports[port].altmode) { > + dev_err(dev, "multiple connector definition for port %u\n", port); > + return -EINVAL; > + } > + > + alt_port = &altmode->ports[port]; > + alt_port->altmode = altmode; > + alt_port->index = port; > + INIT_WORK(&alt_port->work, pmic_glink_altmode_worker); > + > + alt_port->bridge.funcs = &pmic_glink_altmode_bridge_funcs; > + alt_port->bridge.of_node = to_of_node(fwnode); > + alt_port->bridge.ops = DRM_BRIDGE_OP_HPD; > + alt_port->bridge.type = DRM_MODE_CONNECTOR_USB; > + > + ret = devm_drm_bridge_add(dev, &alt_port->bridge); > + if (ret) > + return ret; > + > + alt_port->dp_alt.svid = USB_TYPEC_DP_SID; > + alt_port->dp_alt.mode = USB_TYPEC_DP_MODE; > + alt_port->dp_alt.active = 1; > + > + mux_desc.svid = USB_TYPEC_DP_SID; > + mux_desc.mode = USB_TYPEC_DP_MODE; > + alt_port->typec_mux = fwnode_typec_mux_get(fwnode, &mux_desc); > + if (IS_ERR(alt_port->typec_mux)) > + return dev_err_probe(dev, PTR_ERR(alt_port->typec_mux), > + "failed to acquire mode-switch for port: %d\n", > + port); > + > + ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_mux, > + alt_port->typec_mux); > + if (ret) > + return ret; > + > + alt_port->typec_switch = fwnode_typec_switch_get(fwnode); > + if (IS_ERR(alt_port->typec_switch)) > + return dev_err_probe(dev, PTR_ERR(alt_port->typec_switch), > + "failed to acquire orientation-switch for port: %d\n", > + port); > + > + ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_switch, > + alt_port->typec_switch); > + if (ret) > + return ret; > + } > + > + altmode->client = devm_pmic_glink_register_client(dev, > + altmode->owner_id, > + pmic_glink_altmode_callback, > + pmic_glink_altmode_pdr_notify, > + altmode); > + return PTR_ERR_OR_ZERO(altmode->client); > +} > + > +static const struct auxiliary_device_id pmic_glink_altmode_id_table[] = { > + { .name = "pmic_glink.altmode", }, > + {}, > +}; > +MODULE_DEVICE_TABLE(auxiliary, pmic_glink_altmode_id_table); > + > +static struct auxiliary_driver pmic_glink_altmode_driver = { > + .name = "pmic_glink_altmode", > + .probe = pmic_glink_altmode_probe, > + .id_table = pmic_glink_altmode_id_table, > +}; > + > +module_auxiliary_driver(pmic_glink_altmode_driver); > + > +MODULE_DESCRIPTION("Qualcomm PMIC GLINK Altmode driver"); > +MODULE_LICENSE("GPL"); > -- > 2.37.3 >
On Sun, Jan 15, 2023 at 01:10:14PM -0600, Steev Klimaszewski wrote: > > diff --git a/drivers/soc/qcom/pmic_glink_altmode.c b/drivers/soc/qcom/pmic_glink_altmode.c [..] > > + msg = data; > > + notification = le32_to_cpu(msg->notification); > > + port = FIELD_GET(SC8180X_PORT_MASK, notification); > > + orientation = FIELD_GET(SC8180X_ORIENTATION_MASK, notification); > > + mux = FIELD_GET(SC8180X_MUX_MASK, notification); > > + mode = FIELD_GET(SC8180X_MODE_MASK, notification); > > + hpd_state = FIELD_GET(SC8180X_HPD_STATE_MASK, notification); > > + hpd_irq = FIELD_GET(SC8180X_HPD_IRQ_MASK, notification); > > + > The kernel test robot keeps complaining about these FIELD_GET because > there is no #include <linux/bitfield.h> > I must have missed those complains before, thanks for pointing it out! Regards, Bjorn
On 13/01/2023 05:11, Bjorn Andersson wrote: > From: Bjorn Andersson <bjorn.andersson@linaro.org> > > With the PMIC GLINK service, the host OS subscribes to USB-C altmode > messages, which are sent by the firmware to notify the host OS about > state updates and HPD interrupts. > > The pmic_glink_altmode driver registers for these notifications and > propagates the notifications as typec_mux, typec_switch and DRM OOB > notifications as necessary to implement DisplayPort altmode support. > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> > --- > > Changes since v1: > - None > > Johan reported a NULL pointer dereference in > drm_kms_helper_hotplug_event() for HPD event being reported while the > MSM DRM driver is still being initalized, a separate fix has been sent > in hope to remidy this race condition in the MSM driver. > > drivers/soc/qcom/Makefile | 1 + > drivers/soc/qcom/pmic_glink_altmode.c | 477 ++++++++++++++++++++++++++ > 2 files changed, 478 insertions(+) > create mode 100644 drivers/soc/qcom/pmic_glink_altmode.c > > diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile > index 29cccac472f3..f30552bf4da7 100644 > --- a/drivers/soc/qcom/Makefile > +++ b/drivers/soc/qcom/Makefile > @@ -10,6 +10,7 @@ obj-$(CONFIG_QCOM_MDT_LOADER) += mdt_loader.o > obj-$(CONFIG_QCOM_OCMEM) += ocmem.o > obj-$(CONFIG_QCOM_PDR_HELPERS) += pdr_interface.o > obj-$(CONFIG_QCOM_PMIC_GLINK) += pmic_glink.o > +obj-$(CONFIG_QCOM_PMIC_GLINK) += pmic_glink_altmode.o > obj-$(CONFIG_QCOM_QMI_HELPERS) += qmi_helpers.o > qmi_helpers-y += qmi_encdec.o qmi_interface.o > obj-$(CONFIG_QCOM_RAMP_CTRL) += ramp_controller.o > diff --git a/drivers/soc/qcom/pmic_glink_altmode.c b/drivers/soc/qcom/pmic_glink_altmode.c > new file mode 100644 > index 000000000000..8d2d563cb756 > --- /dev/null > +++ b/drivers/soc/qcom/pmic_glink_altmode.c > @@ -0,0 +1,477 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved. > + * Copyright (c) 2022, Linaro Ltd > + */ > +#include <linux/auxiliary_bus.h> > +#include <linux/module.h> > +#include <linux/of_device.h> > +#include <linux/mutex.h> > +#include <linux/property.h> > +#include <linux/soc/qcom/pdr.h> > +#include <drm/drm_bridge.h> > + > +#include <linux/usb/typec_altmode.h> > +#include <linux/usb/typec_dp.h> > +#include <linux/usb/typec_mux.h> > + > +#include <linux/soc/qcom/pmic_glink.h> > + > +#define PMIC_GLINK_MAX_PORTS 2 > + > +#define USBC_SC8180X_NOTIFY_IND 0x13 > +#define USBC_CMD_WRITE_REQ 0x15 > +#define USBC_NOTIFY_IND 0x16 > + > +#define ALTMODE_PAN_EN 0x10 > +#define ALTMODE_PAN_ACK 0x11 > + > +struct usbc_write_req { > + struct pmic_glink_hdr hdr; > + __le32 cmd; > + __le32 arg; > + __le32 reserved; > +}; > + > +#define NOTIFY_PAYLOAD_SIZE 16 > +struct usbc_notify { > + struct pmic_glink_hdr hdr; > + char payload[NOTIFY_PAYLOAD_SIZE]; > + u32 reserved; > +}; > + > +struct usbc_sc8180x_notify { > + struct pmic_glink_hdr hdr; > + __le32 notification; > + __le32 reserved[2]; > +}; > + > +enum pmic_glink_altmode_pin_assignment { > + DPAM_HPD_OUT, > + DPAM_HPD_A, > + DPAM_HPD_B, > + DPAM_HPD_C, > + DPAM_HPD_D, > + DPAM_HPD_E, > + DPAM_HPD_F, > +}; > + > +struct pmic_glink_altmode; > + > +#define work_to_altmode_port(w) container_of((w), struct pmic_glink_altmode_port, work) > + > +struct pmic_glink_altmode_port { > + struct pmic_glink_altmode *altmode; > + unsigned int index; > + > + struct typec_switch *typec_switch; > + struct typec_mux *typec_mux; > + struct typec_mux_state state; > + struct typec_altmode dp_alt; > + > + struct work_struct work; > + > + struct drm_bridge bridge; > + > + enum typec_orientation orientation; > + u16 svid; > + u8 dp_data; > + u8 mode; > + u8 hpd_state; > + u8 hpd_irq; > +}; > + > +#define work_to_altmode(w) container_of((w), struct pmic_glink_altmode, enable_work) > + > +struct pmic_glink_altmode { > + struct device *dev; > + > + unsigned int owner_id; > + > + /* To synchronize WRITE_REQ acks */ > + struct mutex lock; > + > + struct completion pan_ack; > + struct pmic_glink_client *client; > + > + struct work_struct enable_work; > + > + struct pmic_glink_altmode_port ports[PMIC_GLINK_MAX_PORTS]; > +}; > + > +static int pmic_glink_altmode_request(struct pmic_glink_altmode *altmode, u32 cmd, u32 arg) > +{ > + struct usbc_write_req req = {}; > + unsigned long left; > + int ret; > + > + /* > + * The USBC_CMD_WRITE_REQ ack doesn't identify the request, so wait for > + * one ack at a time. > + */ > + mutex_lock(&altmode->lock); > + > + req.hdr.owner = cpu_to_le32(altmode->owner_id); > + req.hdr.type = cpu_to_le32(PMIC_GLINK_REQ_RESP); > + req.hdr.opcode = cpu_to_le32(USBC_CMD_WRITE_REQ); > + req.cmd = cpu_to_le32(cmd); > + req.arg = cpu_to_le32(arg); > + > + ret = pmic_glink_send(altmode->client, &req, sizeof(req)); > + if (ret) { > + dev_err(altmode->dev, "failed to send altmode request: %#x (%d)\n", cmd, ret); > + goto out_unlock; > + } > + > + left = wait_for_completion_timeout(&altmode->pan_ack, 5 * HZ); > + if (!left) { > + dev_err(altmode->dev, "timeout waiting for altmode request ack for: %#x\n", cmd); > + ret = -ETIMEDOUT; > + } > + > +out_unlock: > + mutex_unlock(&altmode->lock); > + return ret; > +} > + > +static void pmic_glink_altmode_enable_dp(struct pmic_glink_altmode *altmode, > + struct pmic_glink_altmode_port *port, > + u8 mode, bool hpd_state, > + bool hpd_irq) > +{ > + struct typec_displayport_data dp_data = {}; > + int ret; > + > + dp_data.status = DP_STATUS_ENABLED; > + if (hpd_state) > + dp_data.status |= DP_STATUS_HPD_STATE; > + if (hpd_irq) > + dp_data.status |= DP_STATUS_IRQ_HPD; > + dp_data.conf = DP_CONF_SET_PIN_ASSIGN(mode); > + > + port->state.alt = &port->dp_alt; > + port->state.data = &dp_data; > + port->state.mode = TYPEC_MODAL_STATE(mode); > + > + ret = typec_mux_set(port->typec_mux, &port->state); > + if (ret) > + dev_err(altmode->dev, "failed to switch mux to DP\n"); > +} > + > +static void pmic_glink_altmode_enable_usb(struct pmic_glink_altmode *altmode, > + struct pmic_glink_altmode_port *port) > +{ > + int ret; > + > + port->state.alt = NULL; > + port->state.data = NULL; > + port->state.mode = TYPEC_STATE_USB; > + > + ret = typec_mux_set(port->typec_mux, &port->state); > + if (ret) > + dev_err(altmode->dev, "failed to switch mux to USB\n"); > +} > + > +static void pmic_glink_altmode_worker(struct work_struct *work) > +{ > + struct pmic_glink_altmode_port *alt_port = work_to_altmode_port(work); > + struct pmic_glink_altmode *altmode = alt_port->altmode; > + > + typec_switch_set(alt_port->typec_switch, alt_port->orientation); > + > + if (alt_port->svid == USB_TYPEC_DP_SID) > + pmic_glink_altmode_enable_dp(altmode, alt_port, alt_port->mode, > + alt_port->hpd_state, alt_port->hpd_irq); > + else > + pmic_glink_altmode_enable_usb(altmode, alt_port); > + > + if (alt_port->hpd_state) > + drm_bridge_hpd_notify(&alt_port->bridge, connector_status_connected); > + else > + drm_bridge_hpd_notify(&alt_port->bridge, connector_status_disconnected); > + > + pmic_glink_altmode_request(altmode, ALTMODE_PAN_ACK, alt_port->index); > +}; > + > +static enum typec_orientation pmic_glink_altmode_orientation(unsigned int orientation) > +{ > + if (orientation == 0) > + return TYPEC_ORIENTATION_NORMAL; > + else if (orientation == 1) > + return TYPEC_ORIENTATION_REVERSE; > + else > + return TYPEC_ORIENTATION_NONE; > +} > + > +#define SC8180X_PORT_MASK 0x000000ff > +#define SC8180X_ORIENTATION_MASK 0x0000ff00 > +#define SC8180X_MUX_MASK 0x00ff0000 > +#define SC8180X_MODE_MASK 0x3f000000 > +#define SC8180X_HPD_STATE_MASK 0x40000000 > +#define SC8180X_HPD_IRQ_MASK 0x80000000 > + > +static void pmic_glink_altmode_sc8180xp_notify(struct pmic_glink_altmode *altmode, > + const void *data, size_t len) > +{ > + struct pmic_glink_altmode_port *alt_port; > + const struct usbc_sc8180x_notify *msg; > + u32 notification; > + u8 orientation; > + u8 hpd_state; > + u8 hpd_irq; > + u16 svid; > + u8 port; > + u8 mode; > + u8 mux; > + > + if (len != sizeof(*msg)) { > + dev_warn(altmode->dev, "invalid length of USBC_NOTIFY indication: %zd\n", len); > + return; > + } > + > + msg = data; > + notification = le32_to_cpu(msg->notification); > + port = FIELD_GET(SC8180X_PORT_MASK, notification); > + orientation = FIELD_GET(SC8180X_ORIENTATION_MASK, notification); > + mux = FIELD_GET(SC8180X_MUX_MASK, notification); > + mode = FIELD_GET(SC8180X_MODE_MASK, notification); > + hpd_state = FIELD_GET(SC8180X_HPD_STATE_MASK, notification); > + hpd_irq = FIELD_GET(SC8180X_HPD_IRQ_MASK, notification); > + > + svid = mux == 2 ? USB_TYPEC_DP_SID : 0; > + > + if (!altmode->ports[port].altmode) { > + dev_dbg(altmode->dev, "notification on undefined port %d\n", port); > + return; > + } > + > + alt_port = &altmode->ports[port]; > + alt_port->orientation = pmic_glink_altmode_orientation(orientation); > + alt_port->svid = mux == 2 ? USB_TYPEC_DP_SID : 0; > + alt_port->mode = mode; > + alt_port->hpd_state = hpd_state; > + alt_port->hpd_irq = hpd_irq; > + schedule_work(&alt_port->work); > +} > + > +#define SC8280XP_DPAM_MASK 0x3f > +#define SC8280XP_HPD_STATE_MASK BIT(6) > +#define SC8280XP_HPD_IRQ_MASK BIT(7) > + > +static void pmic_glink_altmode_sc8280xp_notify(struct pmic_glink_altmode *altmode, > + u16 svid, const void *data, size_t len) > +{ > + struct pmic_glink_altmode_port *alt_port; > + const struct usbc_notify *notify; > + u8 orientation; > + u8 hpd_state; > + u8 hpd_irq; > + u8 mode; > + u8 port; > + > + if (len != sizeof(*notify)) { > + dev_warn(altmode->dev, "invalid length USBC_NOTIFY_IND: %zd\n", > + len); > + return; > + } > + > + notify = data; > + > + port = notify->payload[0]; > + orientation = notify->payload[1]; > + mode = FIELD_GET(SC8280XP_DPAM_MASK, notify->payload[8]) - DPAM_HPD_A; > + hpd_state = FIELD_GET(SC8280XP_HPD_STATE_MASK, notify->payload[8]); > + hpd_irq = FIELD_GET(SC8280XP_HPD_IRQ_MASK, notify->payload[8]); > + > + if (!altmode->ports[port].altmode) { > + dev_dbg(altmode->dev, "notification on undefined port %d\n", port); > + return; > + } > + > + alt_port = &altmode->ports[port]; > + alt_port->orientation = pmic_glink_altmode_orientation(orientation); > + alt_port->svid = svid; > + alt_port->mode = mode; > + alt_port->hpd_state = hpd_state; > + alt_port->hpd_irq = hpd_irq; > + schedule_work(&alt_port->work); > +} > + > +static void pmic_glink_altmode_callback(const void *data, size_t len, void *priv) > +{ > + struct pmic_glink_altmode *altmode = priv; > + const struct pmic_glink_hdr *hdr = data; > + u16 opcode; > + u16 svid; > + > + opcode = le32_to_cpu(hdr->opcode) & 0xff; > + svid = le32_to_cpu(hdr->opcode) >> 16; > + > + switch (opcode) { > + case USBC_CMD_WRITE_REQ: > + complete(&altmode->pan_ack); > + break; > + case USBC_NOTIFY_IND: > + pmic_glink_altmode_sc8280xp_notify(altmode, svid, data, len); > + break; > + case USBC_SC8180X_NOTIFY_IND: > + pmic_glink_altmode_sc8180xp_notify(altmode, data, len); > + break; > + } > +} > + > +static int pmic_glink_altmode_attach(struct drm_bridge *bridge, > + enum drm_bridge_attach_flags flags) > +{ > + return flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR ? 0 : -EINVAL; > +} > + > +static const struct drm_bridge_funcs pmic_glink_altmode_bridge_funcs = { > + .attach = pmic_glink_altmode_attach, > +}; > + > +static void pmic_glink_altmode_put_mux(void *data) > +{ > + typec_mux_put(data); > +} > + > +static void pmic_glink_altmode_put_switch(void *data) > +{ > + typec_switch_put(data); > +} > + > +static void pmic_glink_altmode_enable_worker(struct work_struct *work) > +{ > + struct pmic_glink_altmode *altmode = work_to_altmode(work); > + int ret; > + > + ret = pmic_glink_altmode_request(altmode, ALTMODE_PAN_EN, 0); > + if (ret) > + dev_err(altmode->dev, "failed to request altmode notifications\n"); > +} > + > +static void pmic_glink_altmode_pdr_notify(void *priv, int state) > +{ > + struct pmic_glink_altmode *altmode = priv; > + > + if (state == SERVREG_SERVICE_STATE_UP) > + schedule_work(&altmode->enable_work); > +} > + > +static const struct of_device_id pmic_glink_altmode_of_quirks[] = { > + { .compatible = "qcom,sc8180x-pmic-glink", .data = (void *)PMIC_GLINK_OWNER_USBC }, > + {} > +}; > + > +static int pmic_glink_altmode_probe(struct auxiliary_device *adev, > + const struct auxiliary_device_id *id) > +{ > + struct pmic_glink_altmode_port *alt_port; > + struct pmic_glink_altmode *altmode; > + struct typec_altmode_desc mux_desc = {}; > + const struct of_device_id *match; > + struct fwnode_handle *fwnode; > + struct device *dev = &adev->dev; > + u32 port; > + int ret; > + > + altmode = devm_kzalloc(dev, sizeof(*altmode), GFP_KERNEL); > + if (!altmode) > + return -ENOMEM; > + > + altmode->dev = dev; > + > + match = of_match_device(pmic_glink_altmode_of_quirks, dev->parent); > + if (match) > + altmode->owner_id = (unsigned long)match->data; > + else > + altmode->owner_id = PMIC_GLINK_OWNER_USBC_PAN; > + > + INIT_WORK(&altmode->enable_work, pmic_glink_altmode_enable_worker); > + init_completion(&altmode->pan_ack); > + mutex_init(&altmode->lock); > + > + device_for_each_child_node(dev, fwnode) { > + ret = fwnode_property_read_u32(fwnode, "reg", &port); > + if (ret < 0) { > + dev_err(dev, "missing reg property of %pOFn\n", fwnode); > + return ret; > + } > + > + if (port >= ARRAY_SIZE(altmode->ports)) { > + dev_warn(dev, "invalid connector number, ignoring\n"); > + continue; > + } > + > + if (altmode->ports[port].altmode) { > + dev_err(dev, "multiple connector definition for port %u\n", port); > + return -EINVAL; > + } > + > + alt_port = &altmode->ports[port]; > + alt_port->altmode = altmode; > + alt_port->index = port; > + INIT_WORK(&alt_port->work, pmic_glink_altmode_worker); > + > + alt_port->bridge.funcs = &pmic_glink_altmode_bridge_funcs; > + alt_port->bridge.of_node = to_of_node(fwnode); > + alt_port->bridge.ops = DRM_BRIDGE_OP_HPD; > + alt_port->bridge.type = DRM_MODE_CONNECTOR_USB; > + > + ret = devm_drm_bridge_add(dev, &alt_port->bridge); > + if (ret) > + return ret; In my testing, the design of a bridge in the altmode driver made all the probe very fragile, meaning that any device that won't probe in the full usb--pmic-glink--display driver would prevent the whole to actually probe. This is why drm_connector_oob_hotplug_event() was used in drivers/usb/typec/altmodes/displayport.c and a similar design for cec where both attach to a device so there's no probe dependency. I think there's a possible simplification here by using : of_drm_find_bridge() instead on the endpoint target to get the last bridge, or we could probably use the same drm_connector_oob_hotplug_event() but in any way we should add missing pieces in drm_bridge_connector and drm/msm/dp/dp_drm.c First in drm/msm/dp/dp_drm.c, the driver should add the of_node to the DP bridge so it can be found from the dp controller node. Secondly, we could add a fwnode in drm_bridge like in drm_connector and in drm_bridge_connector_init() we could set the connector fwnode to the last bridge fwnode + the connector oob event handler. In this case the drm_connector_oob_hotplug_event() design should work. Anyway, I think the bindings is correct, so it's a matter of implementation to avoid delaying the display driver probe until the pmic_glink probes entirely. Neil > + > + alt_port->dp_alt.svid = USB_TYPEC_DP_SID; > + alt_port->dp_alt.mode = USB_TYPEC_DP_MODE; > + alt_port->dp_alt.active = 1; > + > + mux_desc.svid = USB_TYPEC_DP_SID; > + mux_desc.mode = USB_TYPEC_DP_MODE; > + alt_port->typec_mux = fwnode_typec_mux_get(fwnode, &mux_desc); > + if (IS_ERR(alt_port->typec_mux)) > + return dev_err_probe(dev, PTR_ERR(alt_port->typec_mux), > + "failed to acquire mode-switch for port: %d\n", > + port); > + > + ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_mux, > + alt_port->typec_mux); > + if (ret) > + return ret; > + > + alt_port->typec_switch = fwnode_typec_switch_get(fwnode); > + if (IS_ERR(alt_port->typec_switch)) > + return dev_err_probe(dev, PTR_ERR(alt_port->typec_switch), > + "failed to acquire orientation-switch for port: %d\n", > + port); > + > + ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_switch, > + alt_port->typec_switch); > + if (ret) > + return ret; > + } > + > + altmode->client = devm_pmic_glink_register_client(dev, > + altmode->owner_id, > + pmic_glink_altmode_callback, > + pmic_glink_altmode_pdr_notify, > + altmode); > + return PTR_ERR_OR_ZERO(altmode->client); > +} > + > +static const struct auxiliary_device_id pmic_glink_altmode_id_table[] = { > + { .name = "pmic_glink.altmode", }, > + {}, > +}; > +MODULE_DEVICE_TABLE(auxiliary, pmic_glink_altmode_id_table); > + > +static struct auxiliary_driver pmic_glink_altmode_driver = { > + .name = "pmic_glink_altmode", > + .probe = pmic_glink_altmode_probe, > + .id_table = pmic_glink_altmode_id_table, > +}; > + > +module_auxiliary_driver(pmic_glink_altmode_driver); > + > +MODULE_DESCRIPTION("Qualcomm PMIC GLINK Altmode driver"); > +MODULE_LICENSE("GPL");
On 20/01/2023 11:06, Neil Armstrong wrote: > On 13/01/2023 05:11, Bjorn Andersson wrote: >> From: Bjorn Andersson <bjorn.andersson@linaro.org> >> >> With the PMIC GLINK service, the host OS subscribes to USB-C altmode >> messages, which are sent by the firmware to notify the host OS about >> state updates and HPD interrupts. >> >> The pmic_glink_altmode driver registers for these notifications and >> propagates the notifications as typec_mux, typec_switch and DRM OOB >> notifications as necessary to implement DisplayPort altmode support. >> >> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> >> Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> >> --- >> >> Changes since v1: >> - None >> >> Johan reported a NULL pointer dereference in >> drm_kms_helper_hotplug_event() for HPD event being reported while the >> MSM DRM driver is still being initalized, a separate fix has been sent >> in hope to remidy this race condition in the MSM driver. >> >> drivers/soc/qcom/Makefile | 1 + >> drivers/soc/qcom/pmic_glink_altmode.c | 477 ++++++++++++++++++++++++++ >> 2 files changed, 478 insertions(+) >> create mode 100644 drivers/soc/qcom/pmic_glink_altmode.c >> >> diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile >> index 29cccac472f3..f30552bf4da7 100644 >> --- a/drivers/soc/qcom/Makefile >> +++ b/drivers/soc/qcom/Makefile >> @@ -10,6 +10,7 @@ obj-$(CONFIG_QCOM_MDT_LOADER) += mdt_loader.o >> obj-$(CONFIG_QCOM_OCMEM) += ocmem.o >> obj-$(CONFIG_QCOM_PDR_HELPERS) += pdr_interface.o >> obj-$(CONFIG_QCOM_PMIC_GLINK) += pmic_glink.o >> +obj-$(CONFIG_QCOM_PMIC_GLINK) += pmic_glink_altmode.o >> obj-$(CONFIG_QCOM_QMI_HELPERS) += qmi_helpers.o >> qmi_helpers-y += qmi_encdec.o qmi_interface.o >> obj-$(CONFIG_QCOM_RAMP_CTRL) += ramp_controller.o >> diff --git a/drivers/soc/qcom/pmic_glink_altmode.c b/drivers/soc/qcom/pmic_glink_altmode.c >> new file mode 100644 >> index 000000000000..8d2d563cb756 >> --- /dev/null >> +++ b/drivers/soc/qcom/pmic_glink_altmode.c >> @@ -0,0 +1,477 @@ >> +// SPDX-License-Identifier: GPL-2.0-only >> +/* >> + * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved. >> + * Copyright (c) 2022, Linaro Ltd >> + */ >> +#include <linux/auxiliary_bus.h> >> +#include <linux/module.h> >> +#include <linux/of_device.h> >> +#include <linux/mutex.h> >> +#include <linux/property.h> >> +#include <linux/soc/qcom/pdr.h> >> +#include <drm/drm_bridge.h> >> + >> +#include <linux/usb/typec_altmode.h> >> +#include <linux/usb/typec_dp.h> >> +#include <linux/usb/typec_mux.h> >> + >> +#include <linux/soc/qcom/pmic_glink.h> >> + >> +#define PMIC_GLINK_MAX_PORTS 2 >> + >> +#define USBC_SC8180X_NOTIFY_IND 0x13 >> +#define USBC_CMD_WRITE_REQ 0x15 >> +#define USBC_NOTIFY_IND 0x16 >> + >> +#define ALTMODE_PAN_EN 0x10 >> +#define ALTMODE_PAN_ACK 0x11 >> + >> +struct usbc_write_req { >> + struct pmic_glink_hdr hdr; >> + __le32 cmd; >> + __le32 arg; >> + __le32 reserved; >> +}; >> + >> +#define NOTIFY_PAYLOAD_SIZE 16 >> +struct usbc_notify { >> + struct pmic_glink_hdr hdr; >> + char payload[NOTIFY_PAYLOAD_SIZE]; >> + u32 reserved; >> +}; >> + >> +struct usbc_sc8180x_notify { >> + struct pmic_glink_hdr hdr; >> + __le32 notification; >> + __le32 reserved[2]; >> +}; >> + >> +enum pmic_glink_altmode_pin_assignment { >> + DPAM_HPD_OUT, >> + DPAM_HPD_A, >> + DPAM_HPD_B, >> + DPAM_HPD_C, >> + DPAM_HPD_D, >> + DPAM_HPD_E, >> + DPAM_HPD_F, >> +}; >> + >> +struct pmic_glink_altmode; >> + >> +#define work_to_altmode_port(w) container_of((w), struct pmic_glink_altmode_port, work) >> + >> +struct pmic_glink_altmode_port { >> + struct pmic_glink_altmode *altmode; >> + unsigned int index; >> + >> + struct typec_switch *typec_switch; >> + struct typec_mux *typec_mux; >> + struct typec_mux_state state; >> + struct typec_altmode dp_alt; >> + >> + struct work_struct work; >> + >> + struct drm_bridge bridge; >> + >> + enum typec_orientation orientation; >> + u16 svid; >> + u8 dp_data; >> + u8 mode; >> + u8 hpd_state; >> + u8 hpd_irq; >> +}; >> + >> +#define work_to_altmode(w) container_of((w), struct pmic_glink_altmode, enable_work) >> + >> +struct pmic_glink_altmode { >> + struct device *dev; >> + >> + unsigned int owner_id; >> + >> + /* To synchronize WRITE_REQ acks */ >> + struct mutex lock; >> + >> + struct completion pan_ack; >> + struct pmic_glink_client *client; >> + >> + struct work_struct enable_work; >> + >> + struct pmic_glink_altmode_port ports[PMIC_GLINK_MAX_PORTS]; >> +}; >> + >> +static int pmic_glink_altmode_request(struct pmic_glink_altmode *altmode, u32 cmd, u32 arg) >> +{ >> + struct usbc_write_req req = {}; >> + unsigned long left; >> + int ret; >> + >> + /* >> + * The USBC_CMD_WRITE_REQ ack doesn't identify the request, so wait for >> + * one ack at a time. >> + */ >> + mutex_lock(&altmode->lock); >> + >> + req.hdr.owner = cpu_to_le32(altmode->owner_id); >> + req.hdr.type = cpu_to_le32(PMIC_GLINK_REQ_RESP); >> + req.hdr.opcode = cpu_to_le32(USBC_CMD_WRITE_REQ); >> + req.cmd = cpu_to_le32(cmd); >> + req.arg = cpu_to_le32(arg); >> + >> + ret = pmic_glink_send(altmode->client, &req, sizeof(req)); >> + if (ret) { >> + dev_err(altmode->dev, "failed to send altmode request: %#x (%d)\n", cmd, ret); >> + goto out_unlock; >> + } >> + >> + left = wait_for_completion_timeout(&altmode->pan_ack, 5 * HZ); >> + if (!left) { >> + dev_err(altmode->dev, "timeout waiting for altmode request ack for: %#x\n", cmd); >> + ret = -ETIMEDOUT; >> + } >> + >> +out_unlock: >> + mutex_unlock(&altmode->lock); >> + return ret; >> +} >> + >> +static void pmic_glink_altmode_enable_dp(struct pmic_glink_altmode *altmode, >> + struct pmic_glink_altmode_port *port, >> + u8 mode, bool hpd_state, >> + bool hpd_irq) >> +{ >> + struct typec_displayport_data dp_data = {}; >> + int ret; >> + >> + dp_data.status = DP_STATUS_ENABLED; >> + if (hpd_state) >> + dp_data.status |= DP_STATUS_HPD_STATE; >> + if (hpd_irq) >> + dp_data.status |= DP_STATUS_IRQ_HPD; >> + dp_data.conf = DP_CONF_SET_PIN_ASSIGN(mode); >> + >> + port->state.alt = &port->dp_alt; >> + port->state.data = &dp_data; >> + port->state.mode = TYPEC_MODAL_STATE(mode); >> + >> + ret = typec_mux_set(port->typec_mux, &port->state); >> + if (ret) >> + dev_err(altmode->dev, "failed to switch mux to DP\n"); >> +} >> + >> +static void pmic_glink_altmode_enable_usb(struct pmic_glink_altmode *altmode, >> + struct pmic_glink_altmode_port *port) >> +{ >> + int ret; >> + >> + port->state.alt = NULL; >> + port->state.data = NULL; >> + port->state.mode = TYPEC_STATE_USB; >> + >> + ret = typec_mux_set(port->typec_mux, &port->state); >> + if (ret) >> + dev_err(altmode->dev, "failed to switch mux to USB\n"); >> +} >> + >> +static void pmic_glink_altmode_worker(struct work_struct *work) >> +{ >> + struct pmic_glink_altmode_port *alt_port = work_to_altmode_port(work); >> + struct pmic_glink_altmode *altmode = alt_port->altmode; >> + >> + typec_switch_set(alt_port->typec_switch, alt_port->orientation); >> + >> + if (alt_port->svid == USB_TYPEC_DP_SID) >> + pmic_glink_altmode_enable_dp(altmode, alt_port, alt_port->mode, >> + alt_port->hpd_state, alt_port->hpd_irq); >> + else >> + pmic_glink_altmode_enable_usb(altmode, alt_port); >> + >> + if (alt_port->hpd_state) >> + drm_bridge_hpd_notify(&alt_port->bridge, connector_status_connected); >> + else >> + drm_bridge_hpd_notify(&alt_port->bridge, connector_status_disconnected); >> + >> + pmic_glink_altmode_request(altmode, ALTMODE_PAN_ACK, alt_port->index); >> +}; >> + >> +static enum typec_orientation pmic_glink_altmode_orientation(unsigned int orientation) >> +{ >> + if (orientation == 0) >> + return TYPEC_ORIENTATION_NORMAL; >> + else if (orientation == 1) >> + return TYPEC_ORIENTATION_REVERSE; >> + else >> + return TYPEC_ORIENTATION_NONE; >> +} >> + >> +#define SC8180X_PORT_MASK 0x000000ff >> +#define SC8180X_ORIENTATION_MASK 0x0000ff00 >> +#define SC8180X_MUX_MASK 0x00ff0000 >> +#define SC8180X_MODE_MASK 0x3f000000 >> +#define SC8180X_HPD_STATE_MASK 0x40000000 >> +#define SC8180X_HPD_IRQ_MASK 0x80000000 >> + >> +static void pmic_glink_altmode_sc8180xp_notify(struct pmic_glink_altmode *altmode, >> + const void *data, size_t len) >> +{ >> + struct pmic_glink_altmode_port *alt_port; >> + const struct usbc_sc8180x_notify *msg; >> + u32 notification; >> + u8 orientation; >> + u8 hpd_state; >> + u8 hpd_irq; >> + u16 svid; >> + u8 port; >> + u8 mode; >> + u8 mux; >> + >> + if (len != sizeof(*msg)) { >> + dev_warn(altmode->dev, "invalid length of USBC_NOTIFY indication: %zd\n", len); >> + return; >> + } >> + >> + msg = data; >> + notification = le32_to_cpu(msg->notification); >> + port = FIELD_GET(SC8180X_PORT_MASK, notification); >> + orientation = FIELD_GET(SC8180X_ORIENTATION_MASK, notification); >> + mux = FIELD_GET(SC8180X_MUX_MASK, notification); >> + mode = FIELD_GET(SC8180X_MODE_MASK, notification); >> + hpd_state = FIELD_GET(SC8180X_HPD_STATE_MASK, notification); >> + hpd_irq = FIELD_GET(SC8180X_HPD_IRQ_MASK, notification); >> + >> + svid = mux == 2 ? USB_TYPEC_DP_SID : 0; >> + >> + if (!altmode->ports[port].altmode) { >> + dev_dbg(altmode->dev, "notification on undefined port %d\n", port); >> + return; >> + } >> + >> + alt_port = &altmode->ports[port]; >> + alt_port->orientation = pmic_glink_altmode_orientation(orientation); >> + alt_port->svid = mux == 2 ? USB_TYPEC_DP_SID : 0; >> + alt_port->mode = mode; >> + alt_port->hpd_state = hpd_state; >> + alt_port->hpd_irq = hpd_irq; >> + schedule_work(&alt_port->work); >> +} >> + >> +#define SC8280XP_DPAM_MASK 0x3f >> +#define SC8280XP_HPD_STATE_MASK BIT(6) >> +#define SC8280XP_HPD_IRQ_MASK BIT(7) >> + >> +static void pmic_glink_altmode_sc8280xp_notify(struct pmic_glink_altmode *altmode, >> + u16 svid, const void *data, size_t len) >> +{ >> + struct pmic_glink_altmode_port *alt_port; >> + const struct usbc_notify *notify; >> + u8 orientation; >> + u8 hpd_state; >> + u8 hpd_irq; >> + u8 mode; >> + u8 port; >> + >> + if (len != sizeof(*notify)) { >> + dev_warn(altmode->dev, "invalid length USBC_NOTIFY_IND: %zd\n", >> + len); >> + return; >> + } >> + >> + notify = data; >> + >> + port = notify->payload[0]; >> + orientation = notify->payload[1]; >> + mode = FIELD_GET(SC8280XP_DPAM_MASK, notify->payload[8]) - DPAM_HPD_A; >> + hpd_state = FIELD_GET(SC8280XP_HPD_STATE_MASK, notify->payload[8]); >> + hpd_irq = FIELD_GET(SC8280XP_HPD_IRQ_MASK, notify->payload[8]); >> + >> + if (!altmode->ports[port].altmode) { >> + dev_dbg(altmode->dev, "notification on undefined port %d\n", port); >> + return; >> + } >> + >> + alt_port = &altmode->ports[port]; >> + alt_port->orientation = pmic_glink_altmode_orientation(orientation); >> + alt_port->svid = svid; >> + alt_port->mode = mode; >> + alt_port->hpd_state = hpd_state; >> + alt_port->hpd_irq = hpd_irq; >> + schedule_work(&alt_port->work); >> +} >> + >> +static void pmic_glink_altmode_callback(const void *data, size_t len, void *priv) >> +{ >> + struct pmic_glink_altmode *altmode = priv; >> + const struct pmic_glink_hdr *hdr = data; >> + u16 opcode; >> + u16 svid; >> + >> + opcode = le32_to_cpu(hdr->opcode) & 0xff; >> + svid = le32_to_cpu(hdr->opcode) >> 16; >> + >> + switch (opcode) { >> + case USBC_CMD_WRITE_REQ: >> + complete(&altmode->pan_ack); >> + break; >> + case USBC_NOTIFY_IND: >> + pmic_glink_altmode_sc8280xp_notify(altmode, svid, data, len); >> + break; >> + case USBC_SC8180X_NOTIFY_IND: >> + pmic_glink_altmode_sc8180xp_notify(altmode, data, len); >> + break; >> + } >> +} >> + >> +static int pmic_glink_altmode_attach(struct drm_bridge *bridge, >> + enum drm_bridge_attach_flags flags) >> +{ >> + return flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR ? 0 : -EINVAL; >> +} >> + >> +static const struct drm_bridge_funcs pmic_glink_altmode_bridge_funcs = { >> + .attach = pmic_glink_altmode_attach, >> +}; >> + >> +static void pmic_glink_altmode_put_mux(void *data) >> +{ >> + typec_mux_put(data); >> +} >> + >> +static void pmic_glink_altmode_put_switch(void *data) >> +{ >> + typec_switch_put(data); >> +} >> + >> +static void pmic_glink_altmode_enable_worker(struct work_struct *work) >> +{ >> + struct pmic_glink_altmode *altmode = work_to_altmode(work); >> + int ret; >> + >> + ret = pmic_glink_altmode_request(altmode, ALTMODE_PAN_EN, 0); >> + if (ret) >> + dev_err(altmode->dev, "failed to request altmode notifications\n"); >> +} >> + >> +static void pmic_glink_altmode_pdr_notify(void *priv, int state) >> +{ >> + struct pmic_glink_altmode *altmode = priv; >> + >> + if (state == SERVREG_SERVICE_STATE_UP) >> + schedule_work(&altmode->enable_work); >> +} >> + >> +static const struct of_device_id pmic_glink_altmode_of_quirks[] = { >> + { .compatible = "qcom,sc8180x-pmic-glink", .data = (void *)PMIC_GLINK_OWNER_USBC }, >> + {} >> +}; >> + >> +static int pmic_glink_altmode_probe(struct auxiliary_device *adev, >> + const struct auxiliary_device_id *id) >> +{ >> + struct pmic_glink_altmode_port *alt_port; >> + struct pmic_glink_altmode *altmode; >> + struct typec_altmode_desc mux_desc = {}; >> + const struct of_device_id *match; >> + struct fwnode_handle *fwnode; >> + struct device *dev = &adev->dev; >> + u32 port; >> + int ret; >> + >> + altmode = devm_kzalloc(dev, sizeof(*altmode), GFP_KERNEL); >> + if (!altmode) >> + return -ENOMEM; >> + >> + altmode->dev = dev; >> + >> + match = of_match_device(pmic_glink_altmode_of_quirks, dev->parent); >> + if (match) >> + altmode->owner_id = (unsigned long)match->data; >> + else >> + altmode->owner_id = PMIC_GLINK_OWNER_USBC_PAN; >> + >> + INIT_WORK(&altmode->enable_work, pmic_glink_altmode_enable_worker); >> + init_completion(&altmode->pan_ack); >> + mutex_init(&altmode->lock); >> + >> + device_for_each_child_node(dev, fwnode) { >> + ret = fwnode_property_read_u32(fwnode, "reg", &port); >> + if (ret < 0) { >> + dev_err(dev, "missing reg property of %pOFn\n", fwnode); >> + return ret; >> + } >> + >> + if (port >= ARRAY_SIZE(altmode->ports)) { >> + dev_warn(dev, "invalid connector number, ignoring\n"); >> + continue; >> + } >> + >> + if (altmode->ports[port].altmode) { >> + dev_err(dev, "multiple connector definition for port %u\n", port); >> + return -EINVAL; >> + } >> + >> + alt_port = &altmode->ports[port]; >> + alt_port->altmode = altmode; >> + alt_port->index = port; >> + INIT_WORK(&alt_port->work, pmic_glink_altmode_worker); >> + >> + alt_port->bridge.funcs = &pmic_glink_altmode_bridge_funcs; >> + alt_port->bridge.of_node = to_of_node(fwnode); >> + alt_port->bridge.ops = DRM_BRIDGE_OP_HPD; >> + alt_port->bridge.type = DRM_MODE_CONNECTOR_USB; >> + >> + ret = devm_drm_bridge_add(dev, &alt_port->bridge); >> + if (ret) >> + return ret; > > In my testing, the design of a bridge in the altmode driver made all the probe very fragile, > meaning that any device that won't probe in the full usb--pmic-glink--display driver would > prevent the whole to actually probe. > > This is why drm_connector_oob_hotplug_event() was used in drivers/usb/typec/altmodes/displayport.c > and a similar design for cec where both attach to a device so there's no probe dependency. > > I think there's a possible simplification here by using : > of_drm_find_bridge() instead on the endpoint target to get the last bridge, > or we could probably use the same drm_connector_oob_hotplug_event() but in any way we should > add missing pieces in drm_bridge_connector and drm/msm/dp/dp_drm.c > > First in drm/msm/dp/dp_drm.c, the driver should add the of_node to the DP bridge so it can > be found from the dp controller node. > > Secondly, we could add a fwnode in drm_bridge like in drm_connector and in drm_bridge_connector_init() > we could set the connector fwnode to the last bridge fwnode + the connector oob event handler. > In this case the drm_connector_oob_hotplug_event() design should work. > > Anyway, I think the bindings is correct, so it's a matter of implementation to avoid delaying the > display driver probe until the pmic_glink probes entirely. While looking closely, I don't think we can design differently except moving the bridge code into a dummy bridge into gpu/drm/bridge, but this won't solve anything but make things even more complex. This design follows how generic display connector bridge is designed like in gpu/drm/bridge/display-connector.c so it's valid. So for the DRM Bridge part: Acked-by: Neil Armstrong <neil.armstrong@linaro.org> Neil > > Neil > >> + >> + alt_port->dp_alt.svid = USB_TYPEC_DP_SID; >> + alt_port->dp_alt.mode = USB_TYPEC_DP_MODE; >> + alt_port->dp_alt.active = 1; >> + >> + mux_desc.svid = USB_TYPEC_DP_SID; >> + mux_desc.mode = USB_TYPEC_DP_MODE; >> + alt_port->typec_mux = fwnode_typec_mux_get(fwnode, &mux_desc); >> + if (IS_ERR(alt_port->typec_mux)) >> + return dev_err_probe(dev, PTR_ERR(alt_port->typec_mux), >> + "failed to acquire mode-switch for port: %d\n", >> + port); >> + >> + ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_mux, >> + alt_port->typec_mux); >> + if (ret) >> + return ret; >> + >> + alt_port->typec_switch = fwnode_typec_switch_get(fwnode); >> + if (IS_ERR(alt_port->typec_switch)) >> + return dev_err_probe(dev, PTR_ERR(alt_port->typec_switch), >> + "failed to acquire orientation-switch for port: %d\n", >> + port); >> + >> + ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_switch, >> + alt_port->typec_switch); >> + if (ret) >> + return ret; >> + } >> + >> + altmode->client = devm_pmic_glink_register_client(dev, >> + altmode->owner_id, >> + pmic_glink_altmode_callback, >> + pmic_glink_altmode_pdr_notify, >> + altmode); >> + return PTR_ERR_OR_ZERO(altmode->client); >> +} >> + >> +static const struct auxiliary_device_id pmic_glink_altmode_id_table[] = { >> + { .name = "pmic_glink.altmode", }, >> + {}, >> +}; >> +MODULE_DEVICE_TABLE(auxiliary, pmic_glink_altmode_id_table); >> + >> +static struct auxiliary_driver pmic_glink_altmode_driver = { >> + .name = "pmic_glink_altmode", >> + .probe = pmic_glink_altmode_probe, >> + .id_table = pmic_glink_altmode_id_table, >> +}; >> + >> +module_auxiliary_driver(pmic_glink_altmode_driver); >> + >> +MODULE_DESCRIPTION("Qualcomm PMIC GLINK Altmode driver"); >> +MODULE_LICENSE("GPL"); >
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile index 29cccac472f3..f30552bf4da7 100644 --- a/drivers/soc/qcom/Makefile +++ b/drivers/soc/qcom/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_QCOM_MDT_LOADER) += mdt_loader.o obj-$(CONFIG_QCOM_OCMEM) += ocmem.o obj-$(CONFIG_QCOM_PDR_HELPERS) += pdr_interface.o obj-$(CONFIG_QCOM_PMIC_GLINK) += pmic_glink.o +obj-$(CONFIG_QCOM_PMIC_GLINK) += pmic_glink_altmode.o obj-$(CONFIG_QCOM_QMI_HELPERS) += qmi_helpers.o qmi_helpers-y += qmi_encdec.o qmi_interface.o obj-$(CONFIG_QCOM_RAMP_CTRL) += ramp_controller.o diff --git a/drivers/soc/qcom/pmic_glink_altmode.c b/drivers/soc/qcom/pmic_glink_altmode.c new file mode 100644 index 000000000000..8d2d563cb756 --- /dev/null +++ b/drivers/soc/qcom/pmic_glink_altmode.c @@ -0,0 +1,477 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved. + * Copyright (c) 2022, Linaro Ltd + */ +#include <linux/auxiliary_bus.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/mutex.h> +#include <linux/property.h> +#include <linux/soc/qcom/pdr.h> +#include <drm/drm_bridge.h> + +#include <linux/usb/typec_altmode.h> +#include <linux/usb/typec_dp.h> +#include <linux/usb/typec_mux.h> + +#include <linux/soc/qcom/pmic_glink.h> + +#define PMIC_GLINK_MAX_PORTS 2 + +#define USBC_SC8180X_NOTIFY_IND 0x13 +#define USBC_CMD_WRITE_REQ 0x15 +#define USBC_NOTIFY_IND 0x16 + +#define ALTMODE_PAN_EN 0x10 +#define ALTMODE_PAN_ACK 0x11 + +struct usbc_write_req { + struct pmic_glink_hdr hdr; + __le32 cmd; + __le32 arg; + __le32 reserved; +}; + +#define NOTIFY_PAYLOAD_SIZE 16 +struct usbc_notify { + struct pmic_glink_hdr hdr; + char payload[NOTIFY_PAYLOAD_SIZE]; + u32 reserved; +}; + +struct usbc_sc8180x_notify { + struct pmic_glink_hdr hdr; + __le32 notification; + __le32 reserved[2]; +}; + +enum pmic_glink_altmode_pin_assignment { + DPAM_HPD_OUT, + DPAM_HPD_A, + DPAM_HPD_B, + DPAM_HPD_C, + DPAM_HPD_D, + DPAM_HPD_E, + DPAM_HPD_F, +}; + +struct pmic_glink_altmode; + +#define work_to_altmode_port(w) container_of((w), struct pmic_glink_altmode_port, work) + +struct pmic_glink_altmode_port { + struct pmic_glink_altmode *altmode; + unsigned int index; + + struct typec_switch *typec_switch; + struct typec_mux *typec_mux; + struct typec_mux_state state; + struct typec_altmode dp_alt; + + struct work_struct work; + + struct drm_bridge bridge; + + enum typec_orientation orientation; + u16 svid; + u8 dp_data; + u8 mode; + u8 hpd_state; + u8 hpd_irq; +}; + +#define work_to_altmode(w) container_of((w), struct pmic_glink_altmode, enable_work) + +struct pmic_glink_altmode { + struct device *dev; + + unsigned int owner_id; + + /* To synchronize WRITE_REQ acks */ + struct mutex lock; + + struct completion pan_ack; + struct pmic_glink_client *client; + + struct work_struct enable_work; + + struct pmic_glink_altmode_port ports[PMIC_GLINK_MAX_PORTS]; +}; + +static int pmic_glink_altmode_request(struct pmic_glink_altmode *altmode, u32 cmd, u32 arg) +{ + struct usbc_write_req req = {}; + unsigned long left; + int ret; + + /* + * The USBC_CMD_WRITE_REQ ack doesn't identify the request, so wait for + * one ack at a time. + */ + mutex_lock(&altmode->lock); + + req.hdr.owner = cpu_to_le32(altmode->owner_id); + req.hdr.type = cpu_to_le32(PMIC_GLINK_REQ_RESP); + req.hdr.opcode = cpu_to_le32(USBC_CMD_WRITE_REQ); + req.cmd = cpu_to_le32(cmd); + req.arg = cpu_to_le32(arg); + + ret = pmic_glink_send(altmode->client, &req, sizeof(req)); + if (ret) { + dev_err(altmode->dev, "failed to send altmode request: %#x (%d)\n", cmd, ret); + goto out_unlock; + } + + left = wait_for_completion_timeout(&altmode->pan_ack, 5 * HZ); + if (!left) { + dev_err(altmode->dev, "timeout waiting for altmode request ack for: %#x\n", cmd); + ret = -ETIMEDOUT; + } + +out_unlock: + mutex_unlock(&altmode->lock); + return ret; +} + +static void pmic_glink_altmode_enable_dp(struct pmic_glink_altmode *altmode, + struct pmic_glink_altmode_port *port, + u8 mode, bool hpd_state, + bool hpd_irq) +{ + struct typec_displayport_data dp_data = {}; + int ret; + + dp_data.status = DP_STATUS_ENABLED; + if (hpd_state) + dp_data.status |= DP_STATUS_HPD_STATE; + if (hpd_irq) + dp_data.status |= DP_STATUS_IRQ_HPD; + dp_data.conf = DP_CONF_SET_PIN_ASSIGN(mode); + + port->state.alt = &port->dp_alt; + port->state.data = &dp_data; + port->state.mode = TYPEC_MODAL_STATE(mode); + + ret = typec_mux_set(port->typec_mux, &port->state); + if (ret) + dev_err(altmode->dev, "failed to switch mux to DP\n"); +} + +static void pmic_glink_altmode_enable_usb(struct pmic_glink_altmode *altmode, + struct pmic_glink_altmode_port *port) +{ + int ret; + + port->state.alt = NULL; + port->state.data = NULL; + port->state.mode = TYPEC_STATE_USB; + + ret = typec_mux_set(port->typec_mux, &port->state); + if (ret) + dev_err(altmode->dev, "failed to switch mux to USB\n"); +} + +static void pmic_glink_altmode_worker(struct work_struct *work) +{ + struct pmic_glink_altmode_port *alt_port = work_to_altmode_port(work); + struct pmic_glink_altmode *altmode = alt_port->altmode; + + typec_switch_set(alt_port->typec_switch, alt_port->orientation); + + if (alt_port->svid == USB_TYPEC_DP_SID) + pmic_glink_altmode_enable_dp(altmode, alt_port, alt_port->mode, + alt_port->hpd_state, alt_port->hpd_irq); + else + pmic_glink_altmode_enable_usb(altmode, alt_port); + + if (alt_port->hpd_state) + drm_bridge_hpd_notify(&alt_port->bridge, connector_status_connected); + else + drm_bridge_hpd_notify(&alt_port->bridge, connector_status_disconnected); + + pmic_glink_altmode_request(altmode, ALTMODE_PAN_ACK, alt_port->index); +}; + +static enum typec_orientation pmic_glink_altmode_orientation(unsigned int orientation) +{ + if (orientation == 0) + return TYPEC_ORIENTATION_NORMAL; + else if (orientation == 1) + return TYPEC_ORIENTATION_REVERSE; + else + return TYPEC_ORIENTATION_NONE; +} + +#define SC8180X_PORT_MASK 0x000000ff +#define SC8180X_ORIENTATION_MASK 0x0000ff00 +#define SC8180X_MUX_MASK 0x00ff0000 +#define SC8180X_MODE_MASK 0x3f000000 +#define SC8180X_HPD_STATE_MASK 0x40000000 +#define SC8180X_HPD_IRQ_MASK 0x80000000 + +static void pmic_glink_altmode_sc8180xp_notify(struct pmic_glink_altmode *altmode, + const void *data, size_t len) +{ + struct pmic_glink_altmode_port *alt_port; + const struct usbc_sc8180x_notify *msg; + u32 notification; + u8 orientation; + u8 hpd_state; + u8 hpd_irq; + u16 svid; + u8 port; + u8 mode; + u8 mux; + + if (len != sizeof(*msg)) { + dev_warn(altmode->dev, "invalid length of USBC_NOTIFY indication: %zd\n", len); + return; + } + + msg = data; + notification = le32_to_cpu(msg->notification); + port = FIELD_GET(SC8180X_PORT_MASK, notification); + orientation = FIELD_GET(SC8180X_ORIENTATION_MASK, notification); + mux = FIELD_GET(SC8180X_MUX_MASK, notification); + mode = FIELD_GET(SC8180X_MODE_MASK, notification); + hpd_state = FIELD_GET(SC8180X_HPD_STATE_MASK, notification); + hpd_irq = FIELD_GET(SC8180X_HPD_IRQ_MASK, notification); + + svid = mux == 2 ? USB_TYPEC_DP_SID : 0; + + if (!altmode->ports[port].altmode) { + dev_dbg(altmode->dev, "notification on undefined port %d\n", port); + return; + } + + alt_port = &altmode->ports[port]; + alt_port->orientation = pmic_glink_altmode_orientation(orientation); + alt_port->svid = mux == 2 ? USB_TYPEC_DP_SID : 0; + alt_port->mode = mode; + alt_port->hpd_state = hpd_state; + alt_port->hpd_irq = hpd_irq; + schedule_work(&alt_port->work); +} + +#define SC8280XP_DPAM_MASK 0x3f +#define SC8280XP_HPD_STATE_MASK BIT(6) +#define SC8280XP_HPD_IRQ_MASK BIT(7) + +static void pmic_glink_altmode_sc8280xp_notify(struct pmic_glink_altmode *altmode, + u16 svid, const void *data, size_t len) +{ + struct pmic_glink_altmode_port *alt_port; + const struct usbc_notify *notify; + u8 orientation; + u8 hpd_state; + u8 hpd_irq; + u8 mode; + u8 port; + + if (len != sizeof(*notify)) { + dev_warn(altmode->dev, "invalid length USBC_NOTIFY_IND: %zd\n", + len); + return; + } + + notify = data; + + port = notify->payload[0]; + orientation = notify->payload[1]; + mode = FIELD_GET(SC8280XP_DPAM_MASK, notify->payload[8]) - DPAM_HPD_A; + hpd_state = FIELD_GET(SC8280XP_HPD_STATE_MASK, notify->payload[8]); + hpd_irq = FIELD_GET(SC8280XP_HPD_IRQ_MASK, notify->payload[8]); + + if (!altmode->ports[port].altmode) { + dev_dbg(altmode->dev, "notification on undefined port %d\n", port); + return; + } + + alt_port = &altmode->ports[port]; + alt_port->orientation = pmic_glink_altmode_orientation(orientation); + alt_port->svid = svid; + alt_port->mode = mode; + alt_port->hpd_state = hpd_state; + alt_port->hpd_irq = hpd_irq; + schedule_work(&alt_port->work); +} + +static void pmic_glink_altmode_callback(const void *data, size_t len, void *priv) +{ + struct pmic_glink_altmode *altmode = priv; + const struct pmic_glink_hdr *hdr = data; + u16 opcode; + u16 svid; + + opcode = le32_to_cpu(hdr->opcode) & 0xff; + svid = le32_to_cpu(hdr->opcode) >> 16; + + switch (opcode) { + case USBC_CMD_WRITE_REQ: + complete(&altmode->pan_ack); + break; + case USBC_NOTIFY_IND: + pmic_glink_altmode_sc8280xp_notify(altmode, svid, data, len); + break; + case USBC_SC8180X_NOTIFY_IND: + pmic_glink_altmode_sc8180xp_notify(altmode, data, len); + break; + } +} + +static int pmic_glink_altmode_attach(struct drm_bridge *bridge, + enum drm_bridge_attach_flags flags) +{ + return flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR ? 0 : -EINVAL; +} + +static const struct drm_bridge_funcs pmic_glink_altmode_bridge_funcs = { + .attach = pmic_glink_altmode_attach, +}; + +static void pmic_glink_altmode_put_mux(void *data) +{ + typec_mux_put(data); +} + +static void pmic_glink_altmode_put_switch(void *data) +{ + typec_switch_put(data); +} + +static void pmic_glink_altmode_enable_worker(struct work_struct *work) +{ + struct pmic_glink_altmode *altmode = work_to_altmode(work); + int ret; + + ret = pmic_glink_altmode_request(altmode, ALTMODE_PAN_EN, 0); + if (ret) + dev_err(altmode->dev, "failed to request altmode notifications\n"); +} + +static void pmic_glink_altmode_pdr_notify(void *priv, int state) +{ + struct pmic_glink_altmode *altmode = priv; + + if (state == SERVREG_SERVICE_STATE_UP) + schedule_work(&altmode->enable_work); +} + +static const struct of_device_id pmic_glink_altmode_of_quirks[] = { + { .compatible = "qcom,sc8180x-pmic-glink", .data = (void *)PMIC_GLINK_OWNER_USBC }, + {} +}; + +static int pmic_glink_altmode_probe(struct auxiliary_device *adev, + const struct auxiliary_device_id *id) +{ + struct pmic_glink_altmode_port *alt_port; + struct pmic_glink_altmode *altmode; + struct typec_altmode_desc mux_desc = {}; + const struct of_device_id *match; + struct fwnode_handle *fwnode; + struct device *dev = &adev->dev; + u32 port; + int ret; + + altmode = devm_kzalloc(dev, sizeof(*altmode), GFP_KERNEL); + if (!altmode) + return -ENOMEM; + + altmode->dev = dev; + + match = of_match_device(pmic_glink_altmode_of_quirks, dev->parent); + if (match) + altmode->owner_id = (unsigned long)match->data; + else + altmode->owner_id = PMIC_GLINK_OWNER_USBC_PAN; + + INIT_WORK(&altmode->enable_work, pmic_glink_altmode_enable_worker); + init_completion(&altmode->pan_ack); + mutex_init(&altmode->lock); + + device_for_each_child_node(dev, fwnode) { + ret = fwnode_property_read_u32(fwnode, "reg", &port); + if (ret < 0) { + dev_err(dev, "missing reg property of %pOFn\n", fwnode); + return ret; + } + + if (port >= ARRAY_SIZE(altmode->ports)) { + dev_warn(dev, "invalid connector number, ignoring\n"); + continue; + } + + if (altmode->ports[port].altmode) { + dev_err(dev, "multiple connector definition for port %u\n", port); + return -EINVAL; + } + + alt_port = &altmode->ports[port]; + alt_port->altmode = altmode; + alt_port->index = port; + INIT_WORK(&alt_port->work, pmic_glink_altmode_worker); + + alt_port->bridge.funcs = &pmic_glink_altmode_bridge_funcs; + alt_port->bridge.of_node = to_of_node(fwnode); + alt_port->bridge.ops = DRM_BRIDGE_OP_HPD; + alt_port->bridge.type = DRM_MODE_CONNECTOR_USB; + + ret = devm_drm_bridge_add(dev, &alt_port->bridge); + if (ret) + return ret; + + alt_port->dp_alt.svid = USB_TYPEC_DP_SID; + alt_port->dp_alt.mode = USB_TYPEC_DP_MODE; + alt_port->dp_alt.active = 1; + + mux_desc.svid = USB_TYPEC_DP_SID; + mux_desc.mode = USB_TYPEC_DP_MODE; + alt_port->typec_mux = fwnode_typec_mux_get(fwnode, &mux_desc); + if (IS_ERR(alt_port->typec_mux)) + return dev_err_probe(dev, PTR_ERR(alt_port->typec_mux), + "failed to acquire mode-switch for port: %d\n", + port); + + ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_mux, + alt_port->typec_mux); + if (ret) + return ret; + + alt_port->typec_switch = fwnode_typec_switch_get(fwnode); + if (IS_ERR(alt_port->typec_switch)) + return dev_err_probe(dev, PTR_ERR(alt_port->typec_switch), + "failed to acquire orientation-switch for port: %d\n", + port); + + ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_switch, + alt_port->typec_switch); + if (ret) + return ret; + } + + altmode->client = devm_pmic_glink_register_client(dev, + altmode->owner_id, + pmic_glink_altmode_callback, + pmic_glink_altmode_pdr_notify, + altmode); + return PTR_ERR_OR_ZERO(altmode->client); +} + +static const struct auxiliary_device_id pmic_glink_altmode_id_table[] = { + { .name = "pmic_glink.altmode", }, + {}, +}; +MODULE_DEVICE_TABLE(auxiliary, pmic_glink_altmode_id_table); + +static struct auxiliary_driver pmic_glink_altmode_driver = { + .name = "pmic_glink_altmode", + .probe = pmic_glink_altmode_probe, + .id_table = pmic_glink_altmode_id_table, +}; + +module_auxiliary_driver(pmic_glink_altmode_driver); + +MODULE_DESCRIPTION("Qualcomm PMIC GLINK Altmode driver"); +MODULE_LICENSE("GPL");