| Message ID | 20230320154841.327908-13-brgl@bgdev.pl (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: qcom: sa8775p: add basic PMIC support | expand |
On 20.03.2023 16:48, Bartosz Golaszewski wrote: > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > Add the thermal zones and associated alarm nodes for the PMICs that have > them hooked up on sa8775p-ride. > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > --- > arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 58 +++++++++++++++++++++ > 1 file changed, 58 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > index 8616ead3daf5..276070b62ccd 100644 > --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > @@ -6,6 +6,50 @@ > #include <dt-bindings/input/input.h> > #include <dt-bindings/spmi/spmi.h> > > +/ { > + thermal-zones { > + pmm8654au_1_thermal: pm8775-1-thermal { Please reindex this, downstream uses _1 for pmic@0, but this makes little sense. Make it match the SID. > + polling-delay-passive = <100>; > + polling-delay = <0>; > + thermal-sensors = <&pmm8654au_1_temp_alarm>; > + > + trips { > + trip0 { > + temperature = <105000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <125000>; > + hysteresis = <0>; > + type = "critical"; > + }; > + }; > + }; > + What happened to the downstream _2 (pmic@2) one and _4 (pmic@6)? Konrad > + pmm8654au_3_thermal: pm8775-3-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + thermal-sensors = <&pmm8654au_3_temp_alarm>; > + > + trips { > + trip0 { > + temperature = <105000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <125000>; > + hysteresis = <0>; > + type = "critical"; > + }; > + }; > + }; > + }; > +}; > + > &spmi_bus { > pmm8654au_0: pmic@0 { > compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; > @@ -41,6 +85,13 @@ pmm8654au_1: pmic@2 { > reg = <0x2 SPMI_USID>; > #address-cells = <1>; > #size-cells = <0>; > + > + pmm8654au_1_temp_alarm: temp-alarm@a00 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0xa00>; > + interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > }; > > pmm8654au_2: pmic@4 { > @@ -55,5 +106,12 @@ pmm8654au_3: pmic@6 { > reg = <0x6 SPMI_USID>; > #address-cells = <1>; > #size-cells = <0>; > + > + pmm8654au_3_temp_alarm: temp-alarm@a00 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0xa00>; > + interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > }; > };
On Mon, Mar 20, 2023 at 06:28:20PM +0100, Konrad Dybcio wrote: > > > On 20.03.2023 16:48, Bartosz Golaszewski wrote: > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > > > Add the thermal zones and associated alarm nodes for the PMICs that have > > them hooked up on sa8775p-ride. > > > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > --- > > arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 58 +++++++++++++++++++++ > > 1 file changed, 58 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > > index 8616ead3daf5..276070b62ccd 100644 > > --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > > +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > > @@ -6,6 +6,50 @@ > > #include <dt-bindings/input/input.h> > > #include <dt-bindings/spmi/spmi.h> > > > > +/ { > > + thermal-zones { > > + pmm8654au_1_thermal: pm8775-1-thermal { > Please reindex this, downstream uses _1 for pmic@0, but this > makes little sense. Make it match the SID. > Please use the naming from the schematics for these things, rather than just an iterator (which might be what Bartosz is doing here). Regards, Bjorn > > + polling-delay-passive = <100>; > > + polling-delay = <0>; > > + thermal-sensors = <&pmm8654au_1_temp_alarm>; > > + > > + trips { > > + trip0 { > > + temperature = <105000>; > > + hysteresis = <0>; > > + type = "passive"; > > + }; > > + > > + trip1 { > > + temperature = <125000>; > > + hysteresis = <0>; > > + type = "critical"; > > + }; > > + }; > > + }; > > + > What happened to the downstream _2 (pmic@2) one and _4 (pmic@6)? > > Konrad > > > + pmm8654au_3_thermal: pm8775-3-thermal { > > + polling-delay-passive = <100>; > > + polling-delay = <0>; > > + thermal-sensors = <&pmm8654au_3_temp_alarm>; > > + > > + trips { > > + trip0 { > > + temperature = <105000>; > > + hysteresis = <0>; > > + type = "passive"; > > + }; > > + > > + trip1 { > > + temperature = <125000>; > > + hysteresis = <0>; > > + type = "critical"; > > + }; > > + }; > > + }; > > + }; > > +}; > > + > > &spmi_bus { > > pmm8654au_0: pmic@0 { > > compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; > > @@ -41,6 +85,13 @@ pmm8654au_1: pmic@2 { > > reg = <0x2 SPMI_USID>; > > #address-cells = <1>; > > #size-cells = <0>; > > + > > + pmm8654au_1_temp_alarm: temp-alarm@a00 { > > + compatible = "qcom,spmi-temp-alarm"; > > + reg = <0xa00>; > > + interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > > + #thermal-sensor-cells = <0>; > > + }; > > }; > > > > pmm8654au_2: pmic@4 { > > @@ -55,5 +106,12 @@ pmm8654au_3: pmic@6 { > > reg = <0x6 SPMI_USID>; > > #address-cells = <1>; > > #size-cells = <0>; > > + > > + pmm8654au_3_temp_alarm: temp-alarm@a00 { > > + compatible = "qcom,spmi-temp-alarm"; > > + reg = <0xa00>; > > + interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > > + #thermal-sensor-cells = <0>; > > + }; > > }; > > };
On Wed, Mar 22, 2023 at 3:47 AM Bjorn Andersson <andersson@kernel.org> wrote: > > On Mon, Mar 20, 2023 at 06:28:20PM +0100, Konrad Dybcio wrote: > > > > > > On 20.03.2023 16:48, Bartosz Golaszewski wrote: > > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > > > > > Add the thermal zones and associated alarm nodes for the PMICs that have > > > them hooked up on sa8775p-ride. > > > > > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > > --- > > > arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 58 +++++++++++++++++++++ > > > 1 file changed, 58 insertions(+) > > > > > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > > > index 8616ead3daf5..276070b62ccd 100644 > > > --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > > > +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > > > @@ -6,6 +6,50 @@ > > > #include <dt-bindings/input/input.h> > > > #include <dt-bindings/spmi/spmi.h> > > > > > > +/ { > > > + thermal-zones { > > > + pmm8654au_1_thermal: pm8775-1-thermal { > > Please reindex this, downstream uses _1 for pmic@0, but this > > makes little sense. Make it match the SID. > > > > Please use the naming from the schematics for these things, rather than > just an iterator (which might be what Bartosz is doing here). > Not sure how to approach that. All currently existing "qcom,spmi-temp-alarm" nodes use the PMIC name for the label. Otherwise it would have to go into the board file and be replicated for each board using the same PMIC? Bart > Regards, > Bjorn > > > > + polling-delay-passive = <100>; > > > + polling-delay = <0>; > > > + thermal-sensors = <&pmm8654au_1_temp_alarm>; > > > + > > > + trips { > > > + trip0 { > > > + temperature = <105000>; > > > + hysteresis = <0>; > > > + type = "passive"; > > > + }; > > > + > > > + trip1 { > > > + temperature = <125000>; > > > + hysteresis = <0>; > > > + type = "critical"; > > > + }; > > > + }; > > > + }; > > > + > > What happened to the downstream _2 (pmic@2) one and _4 (pmic@6)? > > > > Konrad > > > > > + pmm8654au_3_thermal: pm8775-3-thermal { > > > + polling-delay-passive = <100>; > > > + polling-delay = <0>; > > > + thermal-sensors = <&pmm8654au_3_temp_alarm>; > > > + > > > + trips { > > > + trip0 { > > > + temperature = <105000>; > > > + hysteresis = <0>; > > > + type = "passive"; > > > + }; > > > + > > > + trip1 { > > > + temperature = <125000>; > > > + hysteresis = <0>; > > > + type = "critical"; > > > + }; > > > + }; > > > + }; > > > + }; > > > +}; > > > + > > > &spmi_bus { > > > pmm8654au_0: pmic@0 { > > > compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; > > > @@ -41,6 +85,13 @@ pmm8654au_1: pmic@2 { > > > reg = <0x2 SPMI_USID>; > > > #address-cells = <1>; > > > #size-cells = <0>; > > > + > > > + pmm8654au_1_temp_alarm: temp-alarm@a00 { > > > + compatible = "qcom,spmi-temp-alarm"; > > > + reg = <0xa00>; > > > + interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > > > + #thermal-sensor-cells = <0>; > > > + }; > > > }; > > > > > > pmm8654au_2: pmic@4 { > > > @@ -55,5 +106,12 @@ pmm8654au_3: pmic@6 { > > > reg = <0x6 SPMI_USID>; > > > #address-cells = <1>; > > > #size-cells = <0>; > > > + > > > + pmm8654au_3_temp_alarm: temp-alarm@a00 { > > > + compatible = "qcom,spmi-temp-alarm"; > > > + reg = <0xa00>; > > > + interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > > > + #thermal-sensor-cells = <0>; > > > + }; > > > }; > > > };
diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi index 8616ead3daf5..276070b62ccd 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi @@ -6,6 +6,50 @@ #include <dt-bindings/input/input.h> #include <dt-bindings/spmi/spmi.h> +/ { + thermal-zones { + pmm8654au_1_thermal: pm8775-1-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-sensors = <&pmm8654au_1_temp_alarm>; + + trips { + trip0 { + temperature = <105000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <125000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + + pmm8654au_3_thermal: pm8775-3-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-sensors = <&pmm8654au_3_temp_alarm>; + + trips { + trip0 { + temperature = <105000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <125000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + }; +}; + &spmi_bus { pmm8654au_0: pmic@0 { compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; @@ -41,6 +85,13 @@ pmm8654au_1: pmic@2 { reg = <0x2 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; + + pmm8654au_1_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; }; pmm8654au_2: pmic@4 { @@ -55,5 +106,12 @@ pmm8654au_3: pmic@6 { reg = <0x6 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; + + pmm8654au_3_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; }; };