diff mbox series

[v4,3/3] arm64: dts: qcom: sa8540p-ride: Add ethernet nodes

Message ID 20230411202009.460650-4-ahalaney@redhat.com (mailing list archive)
State Superseded
Headers show
Series Add EMAC3 support for sa8540p-ride (devicetree/clk bits) | expand

Commit Message

Andrew Halaney April 11, 2023, 8:20 p.m. UTC 
Enable both the MACs found on the board.

ethernet0 and ethernet1 both ultimately go to a series of on board
switches which aren't managed by this processor.

ethernet0 is connected to a Marvell 88EA1512 phy via RGMII. That goes to
the series of switches via SGMII on the "media" side of the phy.
RGMII_SGMII mode is enabled via devicetree register descriptions.
The switch on the "media" side has auto-negotiation disabled, so
configuration from userspace similar to:

        ethtool -s eth0 autoneg off speed 1000 duplex full

is necessary to get traffic flowing on that interface.

ethernet1 is in a mac2mac/fixed-link configuration going to the same
series of switches directly via RGMII.

Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
---

Changes since v3:
    * Compatible goes first in node (Krzysztof)

Changes since v1 and v2:
    * None

 arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 180 ++++++++++++++++++++++
 1 file changed, 180 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
index 40db5aa0803c..caad955969bc 100644
--- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -28,6 +28,65 @@  aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <1>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <1>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
 };
 
 &apps_rsc {
@@ -151,6 +210,67 @@  vreg_l8g: ldo8 {
 	};
 };
 
+&ethernet0 {
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	max-speed = <1000>;
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii-txid";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet0_default>;
+
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		/* Marvell 88EA1512 */
+		rgmii_phy: phy@8 {
+			reg = <0x8>;
+
+			interrupt-parent = <&tlmm>;
+			interrupts-extended = <&tlmm 127 IRQ_TYPE_EDGE_FALLING>;
+
+			reset-gpios = <&pmm8540c_gpios 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <11000>;
+			reset-deassert-us = <70000>;
+
+			device_type = "ethernet-phy";
+
+			/* Set to RGMII_SGMII mode and soft reset. Turn off auto-negotiation
+			 * from userspace to talk to the switch on the SGMII side of things
+			 */
+			marvell,reg-init =
+				/* Set MODE[2:0] to RGMII_SGMII */
+				<0x12 0x14 0xfff8 0x4>,
+				/* Soft reset required after changing MODE[2:0] */
+				<0x12 0x14 0x7fff 0x8000>;
+		};
+	};
+};
+
+&ethernet1 {
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	max-speed = <1000>;
+	phy-mode = "rgmii-txid";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet1_default>;
+
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_default>;
@@ -316,6 +436,66 @@  &xo_board_clk {
 /* PINCTRL */
 
 &tlmm {
+	ethernet0_default: ethernet0-default-state {
+		mdc-pins {
+			pins = "gpio175";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		mdio-pins {
+			pins = "gpio176";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-tx-pins {
+			pins = "gpio183", "gpio184", "gpio185", "gpio186", "gpio187", "gpio188";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-rx-pins {
+			pins = "gpio177", "gpio178", "gpio179", "gpio180", "gpio181", "gpio182";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	ethernet1_default: ethernet1-default-state {
+		mdc-pins {
+			pins = "gpio97";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		mdio-pins {
+			pins = "gpio98";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-tx-pins {
+			pins = "gpio105", "gpio106", "gpio107", "gpio108", "gpio109", "gpio110";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-rx-pins {
+			pins = "gpio99", "gpio100", "gpio101", "gpio102", "gpio103", "gpio104";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
 	i2c0_default: i2c0-default-state {
 		/* To USB7002T-I/KDXVA0 USB hub (SIP1 only) */
 		pins = "gpio135", "gpio136";