@@ -31,6 +31,7 @@ / {
aliases {
serial0 = &uart9;
+ serial1 = &uart1;
};
chosen {
@@ -524,6 +525,39 @@ adc-chan@644 {
};
};
+&qup_uart1_cts {
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+};
+
+&qup_uart1_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart1_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
+};
+
+&qup_uart1_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
&qupv3_id_0 {
status = "okay";
};
@@ -561,6 +595,75 @@ &sdhc_2 {
&tlmm {
gpio-reserved-ranges = <13 4>, <56 2>;
+
+ qup_uart1_sleep_cts: qup-uart1-sleep-cts-state {
+ pins = "gpio61";
+ function = "gpio";
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+ };
+
+ qup_uart1_sleep_rts: qup-uart1-sleep-rts-state {
+ pins = "gpio62";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart1_sleep_rx: qup-uart1-sleep-rx-state {
+ pins = "gpio64";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
+ bias-pull-up;
+ };
+
+ qup_uart1_sleep_tx: qup-uart1-sleep-tx-state {
+ pins = "gpio63";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
+ };
+};
+
+&uart1 {
+ /delete-property/ interrupts;
+ interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 64 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&qup_uart1_sleep_cts>, <&qup_uart1_sleep_rts>, <&qup_uart1_sleep_tx>, <&qup_uart1_sleep_rx>;
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3988-bt";
+
+ vddio-supply = <&vreg_l11a>;
+ vddxo-supply = <&vreg_l7a>;
+ vddrf-supply = <&vreg_l2e>;
+ vddch0-supply = <&vreg_l10e>;
+ swctrl-gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>;
+
+ max-speed = <3200000>;
+ };
};
&uart9 {
The device has a WCN3988 chip for WiFi and Bluetooth. Configure the Bluetooth node and enable the UART it is connected to, plus the necessary pinctrl that has been borrowed with comments from sc7280-idp.dtsi. Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> --- arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts | 103 ++++++++++++++++++++++ 1 file changed, 103 insertions(+)