| Message ID | 20230430-drv260x-improvements-v1-5-1fb28b4cc698@z3ntu.xyz (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
| Series | Improvements for drv260x driver and add to Huawei Watch | expand |
On 30.04.2023 20:20, Luca Weiss wrote: > The watch has a DRV2605 for haptics. Add a node for it based on the > values found in the downstream board file. > > Signed-off-by: Luca Weiss <luca@z3ntu.xyz> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts | 28 ++++++++++++++++++++++ > 1 file changed, 28 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts > index d64096028ab1..eb73b992a696 100644 > --- a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts > +++ b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts > @@ -7,6 +7,7 @@ > > #include "qcom-msm8226.dtsi" > #include "qcom-pm8226.dtsi" > +#include <dt-bindings/input/ti-drv260x.h> > > /delete-node/ &adsp_region; > > @@ -68,6 +69,26 @@ &adsp { > status = "okay"; > }; > > +&blsp1_i2c2 { > + clock-frequency = <384000>; > + > + status = "okay"; > + > + vibrator@5a { > + compatible = "ti,drv2605"; > + reg = <0x5a>; > + enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>; > + > + mode = <DRV260X_ERM_MODE>; > + library-sel = <DRV260X_ERM_LIB_D>; > + vib-rated-mv = <2765>; > + vib-overdrive-mv = <3525>; > + > + pinctrl-0 = <&vibrator_default_state>; > + pinctrl-names = "default"; > + }; > +}; > + > &blsp1_i2c5 { > clock-frequency = <384000>; > > @@ -347,6 +368,13 @@ reset-pins { > }; > }; > > + vibrator_default_state: vibrator-default-state { > + pins = "gpio59", "gpio60"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > wlan_hostwake_default_state: wlan-hostwake-default-state { > pins = "gpio66"; > function = "gpio"; >
diff --git a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts index d64096028ab1..eb73b992a696 100644 --- a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts +++ b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts @@ -7,6 +7,7 @@ #include "qcom-msm8226.dtsi" #include "qcom-pm8226.dtsi" +#include <dt-bindings/input/ti-drv260x.h> /delete-node/ &adsp_region; @@ -68,6 +69,26 @@ &adsp { status = "okay"; }; +&blsp1_i2c2 { + clock-frequency = <384000>; + + status = "okay"; + + vibrator@5a { + compatible = "ti,drv2605"; + reg = <0x5a>; + enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>; + + mode = <DRV260X_ERM_MODE>; + library-sel = <DRV260X_ERM_LIB_D>; + vib-rated-mv = <2765>; + vib-overdrive-mv = <3525>; + + pinctrl-0 = <&vibrator_default_state>; + pinctrl-names = "default"; + }; +}; + &blsp1_i2c5 { clock-frequency = <384000>; @@ -347,6 +368,13 @@ reset-pins { }; }; + vibrator_default_state: vibrator-default-state { + pins = "gpio59", "gpio60"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + wlan_hostwake_default_state: wlan-hostwake-default-state { pins = "gpio66"; function = "gpio";
The watch has a DRV2605 for haptics. Add a node for it based on the values found in the downstream board file. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> --- arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts | 28 ++++++++++++++++++++++ 1 file changed, 28 insertions(+)