| Message ID | 20230517235217.1728548-1-quic_bjorande@quicinc.com (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | ef026e592baa01dd7402511e5ced90f4b3ac3d2c |
| Headers | show |
| Series | [v2] arm64: dts: qcom: sc8280xp: Add SDC2 and enable on CRD | expand |
On 18.05.2023 01:52, Bjorn Andersson wrote: > The CRD has Micro SD slot, introduce the necessary DeviceTree nodes for > enabling this. > > Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> > --- > > Changes since v1: > - Order of pinctr-N and pinctrl-names > - Reset GCC_SDCC2_BCR and not sdc4 b4 diff 20230517235217.1728548-1-quic_bjorande@quicinc.com also reveals: - move cd-gpios - add interconnect OPP properties nevertheless: Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > > arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 81 +++++++++++++++++++++++ > arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 43 ++++++++++++ > 2 files changed, 124 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts > index 5b25d54b9591..ff9cebbccfcb 100644 > --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts > @@ -308,6 +308,13 @@ vreg_l1c: ldo1 { > regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > }; > > + vreg_l6c: ldo6 { > + regulator-name = "vreg_l6c"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > vreg_l7c: ldo7 { > regulator-name = "vreg_l7c"; > regulator-min-microvolt = <2504000>; > @@ -318,6 +325,13 @@ vreg_l7c: ldo7 { > RPMH_REGULATOR_MODE_HPM>; > }; > > + vreg_l9c: ldo9 { > + regulator-name = "vreg_l9c"; > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > vreg_l13c: ldo13 { > regulator-name = "vreg_l13c"; > regulator-min-microvolt = <3072000>; > @@ -600,6 +614,19 @@ &remoteproc_nsp0 { > status = "okay"; > }; > > +&sdc2 { > + pinctrl-0 = <&sdc2_default_state>; > + pinctrl-1 = <&sdc2_sleep_state>; > + pinctrl-names = "default", "sleep"; > + > + vmmc-supply = <&vreg_l9c>; > + vqmmc-supply = <&vreg_l6c>; > + > + cd-gpios = <&tlmm 131 GPIO_ACTIVE_LOW>; > + > + status = "okay"; > +}; > + > &uart17 { > compatible = "qcom,geni-debug-uart"; > > @@ -842,6 +869,60 @@ wake-n-pins { > }; > }; > > + sdc2_default_state: sdc2-default-state { > + clk-pins { > + pins = "sdc2_clk"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + cmd-pins { > + pins = "sdc2_cmd"; > + drive-strength = <16>; > + bias-pull-up; > + }; > + > + data-pins { > + pins = "sdc2_data"; > + drive-strength = <16>; > + bias-pull-up; > + }; > + > + card-detect-pins { > + pins = "gpio131"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + }; > + > + sdc2_sleep_state: sdc2-sleep-state { > + clk-pins { > + pins = "sdc2_clk"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + cmd-pins { > + pins = "sdc2_cmd"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + data-pins { > + pins = "sdc2_data"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + card-detect-pins { > + pins = "gpio131"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + }; > + > tpad_default: tpad-default-state { > int-n-pins { > pins = "gpio182"; > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi > index 8fa9fbfe5d00..3711f109aeaf 100644 > --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi > @@ -2815,6 +2815,49 @@ data-pins { > }; > }; > > + sdc2: mmc@8804000 { > + compatible = "qcom,sc8280xp-sdhci", "qcom,sdhci-msm-v5"; > + reg = <0 0x08804000 0 0x1000>; > + > + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC2_AHB_CLK>, > + <&gcc GCC_SDCC2_APPS_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "core", "xo"; > + resets = <&gcc GCC_SDCC2_BCR>; > + interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>, > + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>; > + interconnect-names = "sdhc-ddr","cpu-sdhc"; > + iommus = <&apps_smmu 0x4e0 0x0>; > + power-domains = <&rpmhpd SC8280XP_CX>; > + operating-points-v2 = <&sdc2_opp_table>; > + bus-width = <4>; > + dma-coherent; > + > + status = "disabled"; > + > + sdc2_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-100000000 { > + opp-hz = /bits/ 64 <100000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + opp-peak-kBps = <1800000 400000>; > + opp-avg-kBps = <100000 0>; > + }; > + > + opp-202000000 { > + opp-hz = /bits/ 64 <202000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + opp-peak-kBps = <5400000 1600000>; > + opp-avg-kBps = <200000 0>; > + }; > + }; > + }; > + > usb_0_qmpphy: phy@88eb000 { > compatible = "qcom,sc8280xp-qmp-usb43dp-phy"; > reg = <0 0x088eb000 0 0x4000>;
On Wed, 17 May 2023 16:52:17 -0700, Bjorn Andersson wrote: > The CRD has Micro SD slot, introduce the necessary DeviceTree nodes for > enabling this. > > Applied, thanks! [1/1] arm64: dts: qcom: sc8280xp: Add SDC2 and enable on CRD commit: ef026e592baa01dd7402511e5ced90f4b3ac3d2c Best regards,
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts index 5b25d54b9591..ff9cebbccfcb 100644 --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts @@ -308,6 +308,13 @@ vreg_l1c: ldo1 { regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + vreg_l6c: ldo6 { + regulator-name = "vreg_l6c"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + vreg_l7c: ldo7 { regulator-name = "vreg_l7c"; regulator-min-microvolt = <2504000>; @@ -318,6 +325,13 @@ vreg_l7c: ldo7 { RPMH_REGULATOR_MODE_HPM>; }; + vreg_l9c: ldo9 { + regulator-name = "vreg_l9c"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + vreg_l13c: ldo13 { regulator-name = "vreg_l13c"; regulator-min-microvolt = <3072000>; @@ -600,6 +614,19 @@ &remoteproc_nsp0 { status = "okay"; }; +&sdc2 { + pinctrl-0 = <&sdc2_default_state>; + pinctrl-1 = <&sdc2_sleep_state>; + pinctrl-names = "default", "sleep"; + + vmmc-supply = <&vreg_l9c>; + vqmmc-supply = <&vreg_l6c>; + + cd-gpios = <&tlmm 131 GPIO_ACTIVE_LOW>; + + status = "okay"; +}; + &uart17 { compatible = "qcom,geni-debug-uart"; @@ -842,6 +869,60 @@ wake-n-pins { }; }; + sdc2_default_state: sdc2-default-state { + clk-pins { + pins = "sdc2_clk"; + drive-strength = <16>; + bias-disable; + }; + + cmd-pins { + pins = "sdc2_cmd"; + drive-strength = <16>; + bias-pull-up; + }; + + data-pins { + pins = "sdc2_data"; + drive-strength = <16>; + bias-pull-up; + }; + + card-detect-pins { + pins = "gpio131"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + }; + + sdc2_sleep_state: sdc2-sleep-state { + clk-pins { + pins = "sdc2_clk"; + drive-strength = <2>; + bias-disable; + }; + + cmd-pins { + pins = "sdc2_cmd"; + drive-strength = <2>; + bias-pull-up; + }; + + data-pins { + pins = "sdc2_data"; + drive-strength = <2>; + bias-pull-up; + }; + + card-detect-pins { + pins = "gpio131"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + }; + tpad_default: tpad-default-state { int-n-pins { pins = "gpio182"; diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi index 8fa9fbfe5d00..3711f109aeaf 100644 --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi @@ -2815,6 +2815,49 @@ data-pins { }; }; + sdc2: mmc@8804000 { + compatible = "qcom,sc8280xp-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x08804000 0 0x1000>; + + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_AHB_CLK>, + <&gcc GCC_SDCC2_APPS_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "core", "xo"; + resets = <&gcc GCC_SDCC2_BCR>; + interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>; + interconnect-names = "sdhc-ddr","cpu-sdhc"; + iommus = <&apps_smmu 0x4e0 0x0>; + power-domains = <&rpmhpd SC8280XP_CX>; + operating-points-v2 = <&sdc2_opp_table>; + bus-width = <4>; + dma-coherent; + + status = "disabled"; + + sdc2_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + required-opps = <&rpmhpd_opp_low_svs>; + opp-peak-kBps = <1800000 400000>; + opp-avg-kBps = <100000 0>; + }; + + opp-202000000 { + opp-hz = /bits/ 64 <202000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + opp-peak-kBps = <5400000 1600000>; + opp-avg-kBps = <200000 0>; + }; + }; + }; + usb_0_qmpphy: phy@88eb000 { compatible = "qcom,sc8280xp-qmp-usb43dp-phy"; reg = <0 0x088eb000 0 0x4000>;
The CRD has Micro SD slot, introduce the necessary DeviceTree nodes for enabling this. Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> --- Changes since v1: - Order of pinctr-N and pinctrl-names - Reset GCC_SDCC2_BCR and not sdc4 arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 81 +++++++++++++++++++++++ arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 43 ++++++++++++ 2 files changed, 124 insertions(+)