@@ -23,6 +23,7 @@ / {
aliases {
serial0 = &uart15;
+ serial1 = &uart14;
};
chosen {
@@ -45,6 +46,44 @@ key-volume-up {
};
};
+ pmic-glink {
+ compatible = "qcom,sm8650-pmic-glink",
+ "qcom,sm8550-pmic-glink",
+ "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+ };
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
@@ -399,6 +438,81 @@ vreg_l3i_1p2: ldo3 {
};
};
+&dispcc {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+
+ panel@0 {
+ compatible = "visionox,vtdr6130";
+ reg = <0>;
+
+ reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+ vddio-supply = <&vreg_l12b_1p8>;
+ vci-supply = <&vreg_l13b_3p0>;
+ vdd-supply = <&vreg_l11b_1p2>;
+
+ pinctrl-0 = <&disp0_resetn_active>, <&mdp_vsync_active>;
+ pinctrl-1 = <&disp0_resetn_suspend>, <&mdp_vsync_suspend>;
+ pinctrl-names = "default", "sleep";
+
+ port {
+ panel0_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+ };
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&panel0_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l1i_0p88>;
+
+ status = "okay";
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+ clock-frequency = <1000>;
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1i_0p88>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
&pon_pwrkey {
status = "okay";
};
@@ -479,22 +593,172 @@ &pmk8550_rtc {
status = "okay";
};
+&qupv3_id_0 {
+ status = "okay";
+};
+
&qupv3_id_1 {
status = "okay";
};
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8650/adsp.mbn",
+ "qcom/sm8650/adsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/sm8650/cdsp.mbn",
+ "qcom/sm8650/cdsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ firmware-name = "qcom/sm8650/modem.mbn",
+ "qcom/sm8650/modem_dtb.mbn";
+
+ status = "okay";
+};
+
&sleep_clk {
clock-frequency = <32000>;
};
+&spi4 {
+ status = "okay";
+
+ touchscreen@0 {
+ compatible = "goodix,gt9916";
+ reg = <0>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <162 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&tlmm 161 GPIO_ACTIVE_LOW>;
+
+ avdd-supply = <&vreg_l14b_3p2>;
+
+ spi-max-frequency = <1000000>;
+
+ touchscreen-size-x = <1080>;
+ touchscreen-size-y = <2400>;
+
+ pinctrl-0 = <&ts_irq>, <&ts_reset>;
+ pinctrl-names = "default";
+ };
+};
+
&tlmm {
gpio-reserved-ranges = <32 8>;
+
+ bt_default: bt-default-state {
+ bt-en-pins {
+ pins = "gpio17";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ sw-ctrl-pins {
+ pins = "gpio18";
+ function = "gpio";
+ bias-pull-down;
+ };
+ };
+
+ disp0_resetn_active: disp0-resetn-active-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ disp0_resetn_suspend: disp0-resetn-suspend-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ mdp_vsync_active: mdp-vsync-active-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ mdp_vsync_suspend: mdp-vsync-suspend-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ ts_irq: ts-irq-state {
+ pins = "gpio161";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ output-disable;
+ };
+
+ ts_reset: ts-reset-state {
+ pins = "gpio162";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+
+ clocks = <&rpmhcc RPMH_RF_CLK1>;
+
+ vddio-supply = <&vreg_l3c_1p2>;
+ vddaon-supply = <&vreg_l15b_1p8>;
+ vdddig-supply = <&vreg_s3c_0p9>;
+ vddrfa0p8-supply = <&vreg_s3c_0p9>;
+ vddrfa1p2-supply = <&vreg_s1c_1p2>;
+ vddrfa1p9-supply = <&vreg_s6c_1p8>;
+
+ max-speed = <3200000>;
+
+ enable-gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>;
+ swctrl-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&bt_default>;
+ pinctrl-names = "default";
+ };
};
&uart15 {
status = "okay";
};
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1c_1p2>;
+ vccq-max-microamp = <1200000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
/*
* DPAUX -> WCD9395 -> USB_SBU -> USB-C
* eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> WCD9395 -> USB-C
@@ -506,7 +770,16 @@ &usb_1 {
};
&usb_1_dwc3 {
- dr_mode = "peripheral";
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_1_hsphy {
Now interconnect dependent devices are added in sm8650 DTSI, now enable more devices for the Qualcomm SM8650 QRD board: - PCIe - Display - DSPs - SDCard - UFS - USB role switch with PMIC Glink - Bluetooth Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- arch/arm64/boot/dts/qcom/sm8650-qrd.dts | 275 +++++++++++++++++++++++++++++++- 1 file changed, 274 insertions(+), 1 deletion(-)