| Message ID | 20240104130123.37115-3-brgl@bgdev.pl (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | PCI: introduce the concept of power sequencing of PCIe devices | expand |
On Thu, 4 Jan 2024 at 15:03, Bartosz Golaszewski <brgl@bgdev.pl> wrote: > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > Describe the ath11k WLAN on-board the QCA6390 module. Include the > relevant regulators and the enable GPIO. > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > --- > arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 24 ++++++++++++++++++++++++ > 1 file changed, 24 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > index cd0db4f31d4a..721f86af952b 100644 > --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > @@ -734,6 +734,22 @@ &pcie0_phy { > vdda-pll-supply = <&vreg_l9a_1p2>; > }; > > +&pcieport0 { > + wifi@0 { > + compatible = "pci17cb,1101"; > + reg = <0x10000 0x0 0x0 0x0 0x0>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&wlan_en_state>; > + > + enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; > + > + vddpmu-supply = <&vreg_s2f_0p95>; > + vddpcie1-supply = <&vreg_s8c_1p3>; > + vddpcie2-supply = <&vreg_s5a_1p9>; If I remember correctly, qca6390 has at least 8 power supplies AON, PMU, 3xRFA, 2xPCIe and VDDIO. Moreover, these bindings do not solve another problem: the PMU is shared between WiFi and BT parts. For the next gen (WCN6855) this becomes even more important, see the code in msm-5.10 which makes sure that there is a proper time between one of the units going down and another one being powered on. > + }; > +}; > + > &pcie1 { > status = "okay"; > }; > @@ -1303,6 +1319,14 @@ sdc2_card_det_n: sd-card-det-n-state { > function = "gpio"; > bias-pull-up; > }; > + > + wlan_en_state: wlan-default-state { > + pins = "gpio20"; > + function = "gpio"; > + drive-strength = <16>; > + output-low; > + bias-pull-up; > + }; > }; > > &uart6 { > -- > 2.40.1 > >
On Thu, Jan 4, 2024 at 2:44 PM Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On Thu, 4 Jan 2024 at 15:03, Bartosz Golaszewski <brgl@bgdev.pl> wrote: > > > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > > > Describe the ath11k WLAN on-board the QCA6390 module. Include the > > relevant regulators and the enable GPIO. > > > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > --- > > arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 24 ++++++++++++++++++++++++ > > 1 file changed, 24 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > > index cd0db4f31d4a..721f86af952b 100644 > > --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > > +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > > @@ -734,6 +734,22 @@ &pcie0_phy { > > vdda-pll-supply = <&vreg_l9a_1p2>; > > }; > > > > +&pcieport0 { > > + wifi@0 { > > + compatible = "pci17cb,1101"; > > + reg = <0x10000 0x0 0x0 0x0 0x0>; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&wlan_en_state>; > > + > > + enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; > > + > > + vddpmu-supply = <&vreg_s2f_0p95>; > > + vddpcie1-supply = <&vreg_s8c_1p3>; > > + vddpcie2-supply = <&vreg_s5a_1p9>; > > If I remember correctly, qca6390 has at least 8 power supplies AON, > PMU, 3xRFA, 2xPCIe and VDDIO. > > Moreover, these bindings do not solve another problem: the PMU is > shared between WiFi and BT parts. For the next gen (WCN6855) this > becomes even more important, see the code in msm-5.10 which makes sure > that there is a proper time between one of the units going down and > another one being powered on. > Unified, shared power sequencing for this type of loosely coupled MFD devices is something I have in mind and that will be orthogonal to this. It will come on top of the PCIe power sequencing driver. I wanted to address a simpler issue first. Bartosz > > + }; > > +}; > > + > > &pcie1 { > > status = "okay"; > > }; > > @@ -1303,6 +1319,14 @@ sdc2_card_det_n: sd-card-det-n-state { > > function = "gpio"; > > bias-pull-up; > > }; > > + > > + wlan_en_state: wlan-default-state { > > + pins = "gpio20"; > > + function = "gpio"; > > + drive-strength = <16>; > > + output-low; > > + bias-pull-up; > > + }; > > }; > > > > &uart6 { > > -- > > 2.40.1 > > > > > > > -- > With best wishes > Dmitry
diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index cd0db4f31d4a..721f86af952b 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -734,6 +734,22 @@ &pcie0_phy { vdda-pll-supply = <&vreg_l9a_1p2>; }; +&pcieport0 { + wifi@0 { + compatible = "pci17cb,1101"; + reg = <0x10000 0x0 0x0 0x0 0x0>; + + pinctrl-names = "default"; + pinctrl-0 = <&wlan_en_state>; + + enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; + + vddpmu-supply = <&vreg_s2f_0p95>; + vddpcie1-supply = <&vreg_s8c_1p3>; + vddpcie2-supply = <&vreg_s5a_1p9>; + }; +}; + &pcie1 { status = "okay"; }; @@ -1303,6 +1319,14 @@ sdc2_card_det_n: sd-card-det-n-state { function = "gpio"; bias-pull-up; }; + + wlan_en_state: wlan-default-state { + pins = "gpio20"; + function = "gpio"; + drive-strength = <16>; + output-low; + bias-pull-up; + }; }; &uart6 {