| Message ID | 20240110114033.32575-3-quic_luoj@quicinc.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | net: ethernet: Add qcom PPE driver | expand |
On 10/01/2024 12:40, Luo Jie wrote: > Qualcomm PPE(packet process engine) is supported on > IPQ SOC platform. > A nit, subject: drop second/last, redundant "bindings". The "dt-bindings" prefix is already stating that these are bindings. See also: https://elixir.bootlin.com/linux/v6.7-rc8/source/Documentation/devicetree/bindings/submitting-patches.rst#L18 Basically your subject has only prefix and nothing else useful. Limited review follows, I am not wasting my time much on this. > Signed-off-by: Luo Jie <quic_luoj@quicinc.com> > --- > .../devicetree/bindings/net/qcom,ppe.yaml | 1330 +++++++++++++++++ > 1 file changed, 1330 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/qcom,ppe.yaml > > diff --git a/Documentation/devicetree/bindings/net/qcom,ppe.yaml b/Documentation/devicetree/bindings/net/qcom,ppe.yaml > new file mode 100644 > index 000000000000..6afb2ad62707 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/qcom,ppe.yaml > @@ -0,0 +1,1330 @@ > +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/net/qcom,ppe.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm Packet Process Engine Ethernet controller Where is the ref to ethernet controllers schema? > + > +maintainers: > + - Luo Jie <quic_luoj@quicinc.com> > + > +description: > + The PPE(packet process engine) is comprised of three componets, Ethernet > + DMA, Switch core and Port wrapper, Ethernet DMA is used to transmit and > + receive packets between Ethernet subsytem and host. The Switch core has > + maximum 8 ports(maximum 6 front panel ports and two FIFO interfaces), > + among which there are GMAC/XGMACs used as external interfaces and FIFO > + interfaces connected the EDMA/EIP, The port wrapper provides connections > + from the GMAC/XGMACS to SGMII/QSGMII/PSGMII/USXGMII/10G-BASER etc, there > + are maximu 3 UNIPHY(PCS) instances supported by PPE. > + > +properties: > + compatible: > + enum: > + - qcom,ipq5332-ppe > + - qcom,ipq9574-ppe > + > + reg: > + maxItems: 1 > + > + "#address-cells": > + const: 1 > + > + "#size-cells": > + const: 1 > + > + ranges: true > + > + clocks: true These cannot be true, we expect here widest constraints. > + > + clock-names: true > + > + resets: true > + > + reset-names: true > + > + tdm-config: > + type: object > + additionalProperties: false > + description: | > + PPE TDM(time-division multiplexing) config includes buffer management > + and port scheduler. > + > + properties: > + qcom,tdm-bm-config: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + description: > + The TDM buffer scheduler configs of PPE, there are multiple > + entries supported, each entry includes valid, direction > + (ingress or egress), port, second port valid, second port. > + > + qcom,tdm-port-scheduler-config: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + description: > + The TDM port scheduler management configs of PPE, there > + are multiple entries supported each entry includes ingress > + scheduler port bitmap, ingress scheduler port, egress > + scheduler port, second egress scheduler port valid and > + second egress scheduler port. > + > + required: > + - qcom,tdm-bm-config > + - qcom,tdm-port-scheduler-config > + > + buffer-management-config: > + type: object > + additionalProperties: false > + description: | > + PPE buffer management config, which supports configuring group > + buffer and per port buffer, which decides the threshold of the > + flow control frame generated. > + I don't understand this sentence. Rephrase it to proper sentence and proper hardware, not driver, description. > + properties: > + qcom,group-config: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + description: > + The PPE buffer support 4 groups, the entry includes > + the group ID and group buffer numbers, each buffer > + has 256 bytes. Missing constraints, like min/max and number of items. > + > + qcom,port-config: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + description: > + The PPE buffer number is also assigned per BM port ID, > + there are 10 BM ports supported on ipq5332, and 15 BM > + ports supported on ipq9574. Each entry includs group > + ID, BM port ID, dedicated buffer, the buffer numbers > + for receiving packet after pause frame sent, the > + threshold for pause frame, weight, restore ceil and > + dynamic buffer or static buffer management. > + > + required: > + - qcom,group-config > + - qcom,port-config > + > + queue-management-config: > + type: object > + additionalProperties: false > + description: | > + PPE queue management config, which supports configuring group > + and per queue buffer limitation, which decides the threshold > + to drop the packet on the egress port. > + > + properties: > + qcom,group-config: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + description: > + The PPE queue management support 4 groups, the entry > + includes the group ID, group buffer number, dedicated > + buffer number, threshold to drop packet and restore > + ceil. > + > + qcom,queue-config: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + description: > + PPE has 256 unicast queues and 44 multicast queues, the > + entry includes queue base, queue number, group ID, > + dedicated buffer, the threshold to drop packet, weight, > + restore ceil and dynamic or static queue management. > + > + required: > + - qcom,group-config > + - qcom,queue-config > + > + port-scheduler-resource: > + type: object > + additionalProperties: false > + description: The scheduler resource available in PPE. > + patternProperties: > + "^port[0-7]$": port- > + description: Each subnode represents the scheduler resource per port. > + type: object > + properties: > + port-id: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: | Do not need '|' unless you need to preserve formatting. This applies everywhere. > + The PPE port ID, there are maximum 6 physical port, > + EIP port and CPU port. Your node name suffix says 8 ports. Anyway, missing min/max. All these nodes (before, here and further) looks like dump of vendor code. I expect some good explanation why we should accept this. Commit msg you wrote is meaningless. It literally brings zero information about hardware. You have been asked to provide accurate hardware description yet you keep ignoring people's feedback. ... > + > +patternProperties: phy@ Node names should be generic. See also an explanation and list of examples (not exhaustive) in DT specification: https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation > + "^qcom-uniphy@[0-9a-f]+$": > + type: object > + additionalProperties: false > + description: uniphy configuration and clock provider > + properties: > + reg: > + minItems: 2 > + items: > + - description: The first uniphy register range > + - description: The second uniphy register range > + - description: The third uniphy register range first, second and third are really useless descriptions. We expect something useful. > + > + "#clock-cells": > + const: 1 > + > + clock-output-names: > + minItems: 4 > + maxItems: 6 > + > + required: > + - reg > + - "#clock-cells" > + - clock-output-names > + > +allOf: > + - if: > + properties: > + compatible: > + contains: > + const: qcom,ipq5332-ppe > + then: > + properties: > + clocks: > + items: > + - description: Display common AHB clock from gcc > + - description: Display common system clock from gcc > + - description: Display uniphy0 AHB clock from gcc > + - description: Display uniphy1 AHB clock from gcc > + - description: Display uniphy0 system clock from gcc > + - description: Display uniphy1 system clock from gcc > + - description: Display nss clock from gcc > + - description: Display nss noc snoc clock from gcc > + - description: Display nss noc snoc_1 clock from gcc > + - description: Display sleep clock from gcc > + - description: Display PPE clock from nsscc > + - description: Display PPE config clock from nsscc > + - description: Display NSSNOC PPE clock from nsscc > + - description: Display NSSNOC PPE config clock from nsscc > + - description: Display EDMA clock from nsscc > + - description: Display EDMA config clock from nsscc > + - description: Display PPE IPE clock from nsscc > + - description: Display PPE BTQ clock from nsscc > + - description: Display port1 MAC clock from nsscc > + - description: Display port2 MAC clock from nsscc > + - description: Display port1 RX clock from nsscc > + - description: Display port1 TX clock from nsscc > + - description: Display port2 RX clock from nsscc > + - description: Display port2 TX clock from nsscc > + - description: Display UNIPHY port1 RX clock from nsscc > + - description: Display UNIPHY port1 TX clock from nsscc > + - description: Display UNIPHY port2 RX clock from nsscc > + - description: Display UNIPHY port2 TX clock from nsscc > + clock-names: > + items: > + - const: cmn_ahb > + - const: cmn_sys > + - const: uniphy0_ahb > + - const: uniphy1_ahb > + - const: uniphy0_sys > + - const: uniphy1_sys > + - const: gcc_nsscc > + - const: gcc_nssnoc_snoc > + - const: gcc_nssnoc_snoc_1 > + - const: gcc_im_sleep > + - const: nss_ppe > + - const: nss_ppe_cfg > + - const: nssnoc_ppe > + - const: nssnoc_ppe_cfg > + - const: nss_edma > + - const: nss_edma_cfg > + - const: nss_ppe_ipe > + - const: nss_ppe_btq > + - const: port1_mac > + - const: port2_mac > + - const: nss_port1_rx > + - const: nss_port1_tx > + - const: nss_port2_rx > + - const: nss_port2_tx > + - const: uniphy_port1_rx > + - const: uniphy_port1_tx > + - const: uniphy_port2_rx > + - const: uniphy_port2_tx > + > + resets: > + items: > + - description: Reset PPE > + - description: Reset uniphy0 software config > + - description: Reset uniphy1 software config > + - description: Reset uniphy0 AHB > + - description: Reset uniphy1 AHB > + - description: Reset uniphy0 system > + - description: Reset uniphy1 system > + - description: Reset uniphy0 XPCS > + - description: Reset uniphy1 SPCS > + - description: Reset uniphy port1 RX > + - description: Reset uniphy port1 TX > + - description: Reset uniphy port2 RX > + - description: Reset uniphy port2 TX > + - description: Reset PPE port1 RX > + - description: Reset PPE port1 TX > + - description: Reset PPE port2 RX > + - description: Reset PPE port2 TX > + - description: Reset PPE port1 MAC > + - description: Reset PPE port2 MAC > + > + reset-names: > + items: > + - const: ppe > + - const: uniphy0_soft > + - const: uniphy1_soft > + - const: uniphy0_ahb > + - const: uniphy1_ahb > + - const: uniphy0_sys > + - const: uniphy1_sys > + - const: uniphy0_xpcs > + - const: uniphy1_xpcs > + - const: uniphy_port1_rx > + - const: uniphy_port1_tx > + - const: uniphy_port2_rx > + - const: uniphy_port2_tx > + - const: nss_port1_rx > + - const: nss_port1_tx > + - const: nss_port2_rx > + - const: nss_port2_tx > + - const: nss_port1_mac > + - const: nss_port2_mac > + > + - if: > + properties: > + compatible: > + contains: > + const: qcom,ipq9574-ppe > + then: > + properties: > + clocks: > + items: > + - description: Display common AHB clock from gcc > + - description: Display common system clock from gcc > + - description: Display uniphy0 AHB clock from gcc > + - description: Display uniphy1 AHB clock from gcc > + - description: Display uniphy2 AHB clock from gcc > + - description: Display uniphy0 system clock from gcc > + - description: Display uniphy1 system clock from gcc > + - description: Display uniphy2 system clock from gcc > + - description: Display nss clock from gcc > + - description: Display nss noc clock from gcc > + - description: Display nss noc snoc clock from gcc > + - description: Display nss noc snoc_1 clock from gcc > + - description: Display PPE clock from nsscc > + - description: Display PPE config clock from nsscc > + - description: Display NSSNOC PPE clock from nsscc > + - description: Display NSSNOC PPE config clock from nsscc > + - description: Display EDMA clock from nsscc > + - description: Display EDMA config clock from nsscc > + - description: Display PPE IPE clock from nsscc > + - description: Display PPE BTQ clock from nsscc > + - description: Display port1 MAC clock from nsscc > + - description: Display port2 MAC clock from nsscc > + - description: Display port3 MAC clock from nsscc > + - description: Display port4 MAC clock from nsscc > + - description: Display port5 MAC clock from nsscc > + - description: Display port6 MAC clock from nsscc > + - description: Display port1 RX clock from nsscc > + - description: Display port1 TX clock from nsscc > + - description: Display port2 RX clock from nsscc > + - description: Display port2 TX clock from nsscc > + - description: Display port3 RX clock from nsscc > + - description: Display port3 TX clock from nsscc > + - description: Display port4 RX clock from nsscc > + - description: Display port4 TX clock from nsscc > + - description: Display port5 RX clock from nsscc > + - description: Display port5 TX clock from nsscc > + - description: Display port6 RX clock from nsscc > + - description: Display port6 TX clock from nsscc > + - description: Display UNIPHY port1 RX clock from nsscc > + - description: Display UNIPHY port1 TX clock from nsscc > + - description: Display UNIPHY port2 RX clock from nsscc > + - description: Display UNIPHY port2 TX clock from nsscc > + - description: Display UNIPHY port3 RX clock from nsscc > + - description: Display UNIPHY port3 TX clock from nsscc > + - description: Display UNIPHY port4 RX clock from nsscc > + - description: Display UNIPHY port4 TX clock from nsscc > + - description: Display UNIPHY port5 RX clock from nsscc > + - description: Display UNIPHY port5 TX clock from nsscc > + - description: Display UNIPHY port6 RX clock from nsscc > + - description: Display UNIPHY port6 TX clock from nsscc > + - description: Display port5 RX clock source from nsscc > + - description: Display port5 TX clock source from nsscc > + clock-names: > + items: > + - const: cmn_ahb > + - const: cmn_sys > + - const: uniphy0_ahb > + - const: uniphy1_ahb > + - const: uniphy2_ahb > + - const: uniphy0_sys > + - const: uniphy1_sys > + - const: uniphy2_sys > + - const: gcc_nsscc > + - const: gcc_nssnoc_nsscc > + - const: gcc_nssnoc_snoc > + - const: gcc_nssnoc_snoc_1 > + - const: nss_ppe > + - const: nss_ppe_cfg > + - const: nssnoc_ppe > + - const: nssnoc_ppe_cfg > + - const: nss_edma > + - const: nss_edma_cfg > + - const: nss_ppe_ipe > + - const: nss_ppe_btq > + - const: port1_mac > + - const: port2_mac > + - const: port3_mac > + - const: port4_mac > + - const: port5_mac > + - const: port6_mac > + - const: nss_port1_rx > + - const: nss_port1_tx > + - const: nss_port2_rx > + - const: nss_port2_tx > + - const: nss_port3_rx > + - const: nss_port3_tx > + - const: nss_port4_rx > + - const: nss_port4_tx > + - const: nss_port5_rx > + - const: nss_port5_tx > + - const: nss_port6_rx > + - const: nss_port6_tx > + - const: uniphy_port1_rx > + - const: uniphy_port1_tx > + - const: uniphy_port2_rx > + - const: uniphy_port2_tx > + - const: uniphy_port3_rx > + - const: uniphy_port3_tx > + - const: uniphy_port4_rx > + - const: uniphy_port4_tx > + - const: uniphy_port5_rx > + - const: uniphy_port5_tx > + - const: uniphy_port6_rx > + - const: uniphy_port6_tx > + - const: nss_port5_rx_clk_src > + - const: nss_port5_tx_clk_src > + > + resets: > + items: > + - description: Reset PPE > + - description: Reset uniphy0 software config > + - description: Reset uniphy1 software config > + - description: Reset uniphy2 software config > + - description: Reset uniphy0 AHB > + - description: Reset uniphy1 AHB > + - description: Reset uniphy2 AHB > + - description: Reset uniphy0 system > + - description: Reset uniphy1 system > + - description: Reset uniphy2 system > + - description: Reset uniphy0 XPCS > + - description: Reset uniphy1 XPCS > + - description: Reset uniphy2 XPCS > + - description: Assert uniphy port1 > + - description: Assert uniphy port2 > + - description: Assert uniphy port3 > + - description: Assert uniphy port4 > + - description: Reset PPE port1 > + - description: Reset PPE port2 > + - description: Reset PPE port3 > + - description: Reset PPE port4 > + - description: Reset PPE port5 > + - description: Reset PPE port6 > + - description: Reset PPE port1 MAC > + - description: Reset PPE port2 MAC > + - description: Reset PPE port3 MAC > + - description: Reset PPE port4 MAC > + - description: Reset PPE port5 MAC > + - description: Reset PPE port6 MAC > + > + reset-names: > + items: > + - const: ppe > + - const: uniphy0_soft > + - const: uniphy1_soft > + - const: uniphy2_soft > + - const: uniphy0_ahb > + - const: uniphy1_ahb > + - const: uniphy2_ahb > + - const: uniphy0_sys > + - const: uniphy1_sys > + - const: uniphy2_sys > + - const: uniphy0_xpcs > + - const: uniphy1_xpcs > + - const: uniphy2_xpcs > + - const: uniphy0_port1_dis > + - const: uniphy0_port2_dis > + - const: uniphy0_port3_dis > + - const: uniphy0_port4_dis > + - const: nss_port1 > + - const: nss_port2 > + - const: nss_port3 > + - const: nss_port4 > + - const: nss_port5 > + - const: nss_port6 > + - const: nss_port1_mac > + - const: nss_port2_mac > + - const: nss_port3_mac > + - const: nss_port4_mac > + - const: nss_port5_mac > + - const: nss_port6_mac > + > +required: allOf: goes after required: > + - compatible > + - reg > + - "#address-cells" > + - "#size-cells" > + - ranges > + - clocks > + - clock-names > + - resets > + - reset-names > + - tdm-config > + - buffer-management-config > + - queue-management-config > + - port-scheduler-resource > + - port-scheduler-config > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/qcom,ipq9574-gcc.h> > + #include <dt-bindings/reset/qcom,ipq9574-gcc.h> > + #include <dt-bindings/clock/qcom,ipq9574-nsscc.h> > + #include <dt-bindings/reset/qcom,ipq9574-nsscc.h> > + > + soc { > + #address-cells = <1>; > + #size-cells = <1>; > + qcom_ppe: qcom-ppe@3a000000 { Drop label, Generic node names. > + compatible = "qcom,ipq9574-ppe"; Entire indentation of example is broken. Use one described in the bindings coding style. Best regards, Krzysztof
On Wed, 10 Jan 2024 19:40:14 +0800, Luo Jie wrote: > Qualcomm PPE(packet process engine) is supported on > IPQ SOC platform. > > Signed-off-by: Luo Jie <quic_luoj@quicinc.com> > --- > .../devicetree/bindings/net/qcom,ppe.yaml | 1330 +++++++++++++++++ > 1 file changed, 1330 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/qcom,ppe.yaml > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: Documentation/devicetree/bindings/net/qcom,ppe.example.dts:20:18: fatal error: dt-bindings/clock/qcom,ipq9574-nsscc.h: No such file or directory 20 | #include <dt-bindings/clock/qcom,ipq9574-nsscc.h> | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ compilation terminated. make[2]: *** [scripts/Makefile.lib:419: Documentation/devicetree/bindings/net/qcom,ppe.example.dtb] Error 1 make[2]: *** Waiting for unfinished jobs.... make[1]: *** [/builds/robherring/dt-review-ci/linux/Makefile:1424: dt_binding_check] Error 2 make: *** [Makefile:234: __sub-make] Error 2 doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240110114033.32575-3-quic_luoj@quicinc.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
On 1/10/2024 8:22 PM, Krzysztof Kozlowski wrote: > On 10/01/2024 12:40, Luo Jie wrote: >> Qualcomm PPE(packet process engine) is supported on >> IPQ SOC platform. >> > > A nit, subject: drop second/last, redundant "bindings". The > "dt-bindings" prefix is already stating that these are bindings. > See also: > https://elixir.bootlin.com/linux/v6.7-rc8/source/Documentation/devicetree/bindings/submitting-patches.rst#L18 > > Basically your subject has only prefix and nothing else useful. > > Limited review follows, I am not wasting my time much on this. Will remove the redundant words, and follow up the guidance mentioned in the link. Will correct the subject as well. > >> Signed-off-by: Luo Jie <quic_luoj@quicinc.com> >> --- >> .../devicetree/bindings/net/qcom,ppe.yaml | 1330 +++++++++++++++++ >> 1 file changed, 1330 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/net/qcom,ppe.yaml >> >> diff --git a/Documentation/devicetree/bindings/net/qcom,ppe.yaml b/Documentation/devicetree/bindings/net/qcom,ppe.yaml >> new file mode 100644 >> index 000000000000..6afb2ad62707 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/net/qcom,ppe.yaml >> @@ -0,0 +1,1330 @@ >> +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/net/qcom,ppe.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Qualcomm Packet Process Engine Ethernet controller > > Where is the ref to ethernet controllers schema? Sorry, the title above is not describing the device for this dtbindings correctly. It should say "Qualcomm Packet Process Engine". The reference to the schema for PPE is mentioned above. > >> + >> +maintainers: >> + - Luo Jie <quic_luoj@quicinc.com> >> + >> +description: >> + The PPE(packet process engine) is comprised of three componets, Ethernet >> + DMA, Switch core and Port wrapper, Ethernet DMA is used to transmit and >> + receive packets between Ethernet subsytem and host. The Switch core has >> + maximum 8 ports(maximum 6 front panel ports and two FIFO interfaces), >> + among which there are GMAC/XGMACs used as external interfaces and FIFO >> + interfaces connected the EDMA/EIP, The port wrapper provides connections >> + from the GMAC/XGMACS to SGMII/QSGMII/PSGMII/USXGMII/10G-BASER etc, there >> + are maximu 3 UNIPHY(PCS) instances supported by PPE. >> + >> +properties: >> + compatible: >> + enum: >> + - qcom,ipq5332-ppe >> + - qcom,ipq9574-ppe >> + >> + reg: >> + maxItems: 1 >> + >> + "#address-cells": >> + const: 1 >> + >> + "#size-cells": >> + const: 1 >> + >> + ranges: true >> + >> + clocks: true > > These cannot be true, we expect here widest constraints. Got it, will update to add the right constraints for the properties. > >> + >> + clock-names: true >> + >> + resets: true >> + >> + reset-names: true >> + >> + tdm-config: >> + type: object >> + additionalProperties: false >> + description: | >> + PPE TDM(time-division multiplexing) config includes buffer management >> + and port scheduler. >> + >> + properties: >> + qcom,tdm-bm-config: >> + $ref: /schemas/types.yaml#/definitions/uint32-array >> + description: >> + The TDM buffer scheduler configs of PPE, there are multiple >> + entries supported, each entry includes valid, direction >> + (ingress or egress), port, second port valid, second port. >> + >> + qcom,tdm-port-scheduler-config: >> + $ref: /schemas/types.yaml#/definitions/uint32-array >> + description: >> + The TDM port scheduler management configs of PPE, there >> + are multiple entries supported each entry includes ingress >> + scheduler port bitmap, ingress scheduler port, egress >> + scheduler port, second egress scheduler port valid and >> + second egress scheduler port. >> + >> + required: >> + - qcom,tdm-bm-config >> + - qcom,tdm-port-scheduler-config >> + >> + buffer-management-config: >> + type: object >> + additionalProperties: false >> + description: | >> + PPE buffer management config, which supports configuring group >> + buffer and per port buffer, which decides the threshold of the >> + flow control frame generated. >> + > > I don't understand this sentence. Rephrase it to proper sentence and > proper hardware, not driver, description. Ok, I will edit the description to make it more clear. This information determines the number of hardware buffers configured per port in the PPE. This configuration influences flow control behavior of the port. > >> + properties: >> + qcom,group-config: >> + $ref: /schemas/types.yaml#/definitions/uint32-array >> + description: >> + The PPE buffer support 4 groups, the entry includes >> + the group ID and group buffer numbers, each buffer >> + has 256 bytes. > > Missing constraints, like min/max and number of items. Ok, will add these constraints. > >> + >> + qcom,port-config: >> + $ref: /schemas/types.yaml#/definitions/uint32-array >> + description: >> + The PPE buffer number is also assigned per BM port ID, >> + there are 10 BM ports supported on ipq5332, and 15 BM >> + ports supported on ipq9574. Each entry includs group >> + ID, BM port ID, dedicated buffer, the buffer numbers >> + for receiving packet after pause frame sent, the >> + threshold for pause frame, weight, restore ceil and >> + dynamic buffer or static buffer management. >> + >> + required: >> + - qcom,group-config >> + - qcom,port-config >> + >> + queue-management-config: >> + type: object >> + additionalProperties: false >> + description: | >> + PPE queue management config, which supports configuring group >> + and per queue buffer limitation, which decides the threshold >> + to drop the packet on the egress port. >> + >> + properties: >> + qcom,group-config: >> + $ref: /schemas/types.yaml#/definitions/uint32-array >> + description: >> + The PPE queue management support 4 groups, the entry >> + includes the group ID, group buffer number, dedicated >> + buffer number, threshold to drop packet and restore >> + ceil. >> + >> + qcom,queue-config: >> + $ref: /schemas/types.yaml#/definitions/uint32-array >> + description: >> + PPE has 256 unicast queues and 44 multicast queues, the >> + entry includes queue base, queue number, group ID, >> + dedicated buffer, the threshold to drop packet, weight, >> + restore ceil and dynamic or static queue management. >> + >> + required: >> + - qcom,group-config >> + - qcom,queue-config >> + >> + port-scheduler-resource: >> + type: object >> + additionalProperties: false >> + description: The scheduler resource available in PPE. >> + patternProperties: >> + "^port[0-7]$": > > port- Ok. will do. > >> + description: Each subnode represents the scheduler resource per port. >> + type: object >> + properties: >> + port-id: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + description: | > > Do not need '|' unless you need to preserve formatting. This applies > everywhere. Got it, will remove it everywhere applicable. > >> + The PPE port ID, there are maximum 6 physical port, >> + EIP port and CPU port. > > Your node name suffix says 8 ports. Anyway, missing min/max. will add the constraints. > > All these nodes (before, here and further) looks like dump of vendor code. > > I expect some good explanation why we should accept this. Commit msg you > wrote is meaningless. It literally brings zero information about hardware. > > You have been asked to provide accurate hardware description yet you > keep ignoring people's feedback. We are reviewing the current DTS to include only relevant information which varies per board, and move rest of the configuration to driver. We will update the commit message and the descriptions in dtbindings about the details of the hardware information for the updated DTS/dtbindings when this patch series resumes. > ... > >> + >> +patternProperties: > > > phy@ > > Node names should be generic. See also an explanation and list of > examples (not exhaustive) in DT specification: > https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation Got it, thanks. Will refer the link and update accordingly. > > >> + "^qcom-uniphy@[0-9a-f]+$": >> + type: object >> + additionalProperties: false >> + description: uniphy configuration and clock provider >> + properties: >> + reg: >> + minItems: 2 >> + items: >> + - description: The first uniphy register range >> + - description: The second uniphy register range >> + - description: The third uniphy register range > > first, second and third are really useless descriptions. We expect > something useful. > I will rephrase the descriptions here to clarify. Depending on the SoC type (IPQ5332 or IPQ9574) there can be two or three UNIPHY(PCS) in the PPE. This property defines the address ranges for the register space of these UNIPHY(PCS) of PPE. >> + >> + "#clock-cells": >> + const: 1 >> + >> + clock-output-names: >> + minItems: 4 >> + maxItems: 6 >> + >> + required: >> + - reg >> + - "#clock-cells" >> + - clock-output-names >> + >> +allOf: >> + - if: >> + properties: >> + compatible: >> + contains: >> + const: qcom,ipq5332-ppe >> + then: >> + properties: >> + clocks: >> + items: >> + - description: Display common AHB clock from gcc >> + - description: Display common system clock from gcc >> + - description: Display uniphy0 AHB clock from gcc >> + - description: Display uniphy1 AHB clock from gcc >> + - description: Display uniphy0 system clock from gcc >> + - description: Display uniphy1 system clock from gcc >> + - description: Display nss clock from gcc >> + - description: Display nss noc snoc clock from gcc >> + - description: Display nss noc snoc_1 clock from gcc >> + - description: Display sleep clock from gcc >> + - description: Display PPE clock from nsscc >> + - description: Display PPE config clock from nsscc >> + - description: Display NSSNOC PPE clock from nsscc >> + - description: Display NSSNOC PPE config clock from nsscc >> + - description: Display EDMA clock from nsscc >> + - description: Display EDMA config clock from nsscc >> + - description: Display PPE IPE clock from nsscc >> + - description: Display PPE BTQ clock from nsscc >> + - description: Display port1 MAC clock from nsscc >> + - description: Display port2 MAC clock from nsscc >> + - description: Display port1 RX clock from nsscc >> + - description: Display port1 TX clock from nsscc >> + - description: Display port2 RX clock from nsscc >> + - description: Display port2 TX clock from nsscc >> + - description: Display UNIPHY port1 RX clock from nsscc >> + - description: Display UNIPHY port1 TX clock from nsscc >> + - description: Display UNIPHY port2 RX clock from nsscc >> + - description: Display UNIPHY port2 TX clock from nsscc >> + clock-names: >> + items: >> + - const: cmn_ahb >> + - const: cmn_sys >> + - const: uniphy0_ahb >> + - const: uniphy1_ahb >> + - const: uniphy0_sys >> + - const: uniphy1_sys >> + - const: gcc_nsscc >> + - const: gcc_nssnoc_snoc >> + - const: gcc_nssnoc_snoc_1 >> + - const: gcc_im_sleep >> + - const: nss_ppe >> + - const: nss_ppe_cfg >> + - const: nssnoc_ppe >> + - const: nssnoc_ppe_cfg >> + - const: nss_edma >> + - const: nss_edma_cfg >> + - const: nss_ppe_ipe >> + - const: nss_ppe_btq >> + - const: port1_mac >> + - const: port2_mac >> + - const: nss_port1_rx >> + - const: nss_port1_tx >> + - const: nss_port2_rx >> + - const: nss_port2_tx >> + - const: uniphy_port1_rx >> + - const: uniphy_port1_tx >> + - const: uniphy_port2_rx >> + - const: uniphy_port2_tx >> + >> + resets: >> + items: >> + - description: Reset PPE >> + - description: Reset uniphy0 software config >> + - description: Reset uniphy1 software config >> + - description: Reset uniphy0 AHB >> + - description: Reset uniphy1 AHB >> + - description: Reset uniphy0 system >> + - description: Reset uniphy1 system >> + - description: Reset uniphy0 XPCS >> + - description: Reset uniphy1 SPCS >> + - description: Reset uniphy port1 RX >> + - description: Reset uniphy port1 TX >> + - description: Reset uniphy port2 RX >> + - description: Reset uniphy port2 TX >> + - description: Reset PPE port1 RX >> + - description: Reset PPE port1 TX >> + - description: Reset PPE port2 RX >> + - description: Reset PPE port2 TX >> + - description: Reset PPE port1 MAC >> + - description: Reset PPE port2 MAC >> + >> + reset-names: >> + items: >> + - const: ppe >> + - const: uniphy0_soft >> + - const: uniphy1_soft >> + - const: uniphy0_ahb >> + - const: uniphy1_ahb >> + - const: uniphy0_sys >> + - const: uniphy1_sys >> + - const: uniphy0_xpcs >> + - const: uniphy1_xpcs >> + - const: uniphy_port1_rx >> + - const: uniphy_port1_tx >> + - const: uniphy_port2_rx >> + - const: uniphy_port2_tx >> + - const: nss_port1_rx >> + - const: nss_port1_tx >> + - const: nss_port2_rx >> + - const: nss_port2_tx >> + - const: nss_port1_mac >> + - const: nss_port2_mac >> + >> + - if: >> + properties: >> + compatible: >> + contains: >> + const: qcom,ipq9574-ppe >> + then: >> + properties: >> + clocks: >> + items: >> + - description: Display common AHB clock from gcc >> + - description: Display common system clock from gcc >> + - description: Display uniphy0 AHB clock from gcc >> + - description: Display uniphy1 AHB clock from gcc >> + - description: Display uniphy2 AHB clock from gcc >> + - description: Display uniphy0 system clock from gcc >> + - description: Display uniphy1 system clock from gcc >> + - description: Display uniphy2 system clock from gcc >> + - description: Display nss clock from gcc >> + - description: Display nss noc clock from gcc >> + - description: Display nss noc snoc clock from gcc >> + - description: Display nss noc snoc_1 clock from gcc >> + - description: Display PPE clock from nsscc >> + - description: Display PPE config clock from nsscc >> + - description: Display NSSNOC PPE clock from nsscc >> + - description: Display NSSNOC PPE config clock from nsscc >> + - description: Display EDMA clock from nsscc >> + - description: Display EDMA config clock from nsscc >> + - description: Display PPE IPE clock from nsscc >> + - description: Display PPE BTQ clock from nsscc >> + - description: Display port1 MAC clock from nsscc >> + - description: Display port2 MAC clock from nsscc >> + - description: Display port3 MAC clock from nsscc >> + - description: Display port4 MAC clock from nsscc >> + - description: Display port5 MAC clock from nsscc >> + - description: Display port6 MAC clock from nsscc >> + - description: Display port1 RX clock from nsscc >> + - description: Display port1 TX clock from nsscc >> + - description: Display port2 RX clock from nsscc >> + - description: Display port2 TX clock from nsscc >> + - description: Display port3 RX clock from nsscc >> + - description: Display port3 TX clock from nsscc >> + - description: Display port4 RX clock from nsscc >> + - description: Display port4 TX clock from nsscc >> + - description: Display port5 RX clock from nsscc >> + - description: Display port5 TX clock from nsscc >> + - description: Display port6 RX clock from nsscc >> + - description: Display port6 TX clock from nsscc >> + - description: Display UNIPHY port1 RX clock from nsscc >> + - description: Display UNIPHY port1 TX clock from nsscc >> + - description: Display UNIPHY port2 RX clock from nsscc >> + - description: Display UNIPHY port2 TX clock from nsscc >> + - description: Display UNIPHY port3 RX clock from nsscc >> + - description: Display UNIPHY port3 TX clock from nsscc >> + - description: Display UNIPHY port4 RX clock from nsscc >> + - description: Display UNIPHY port4 TX clock from nsscc >> + - description: Display UNIPHY port5 RX clock from nsscc >> + - description: Display UNIPHY port5 TX clock from nsscc >> + - description: Display UNIPHY port6 RX clock from nsscc >> + - description: Display UNIPHY port6 TX clock from nsscc >> + - description: Display port5 RX clock source from nsscc >> + - description: Display port5 TX clock source from nsscc >> + clock-names: >> + items: >> + - const: cmn_ahb >> + - const: cmn_sys >> + - const: uniphy0_ahb >> + - const: uniphy1_ahb >> + - const: uniphy2_ahb >> + - const: uniphy0_sys >> + - const: uniphy1_sys >> + - const: uniphy2_sys >> + - const: gcc_nsscc >> + - const: gcc_nssnoc_nsscc >> + - const: gcc_nssnoc_snoc >> + - const: gcc_nssnoc_snoc_1 >> + - const: nss_ppe >> + - const: nss_ppe_cfg >> + - const: nssnoc_ppe >> + - const: nssnoc_ppe_cfg >> + - const: nss_edma >> + - const: nss_edma_cfg >> + - const: nss_ppe_ipe >> + - const: nss_ppe_btq >> + - const: port1_mac >> + - const: port2_mac >> + - const: port3_mac >> + - const: port4_mac >> + - const: port5_mac >> + - const: port6_mac >> + - const: nss_port1_rx >> + - const: nss_port1_tx >> + - const: nss_port2_rx >> + - const: nss_port2_tx >> + - const: nss_port3_rx >> + - const: nss_port3_tx >> + - const: nss_port4_rx >> + - const: nss_port4_tx >> + - const: nss_port5_rx >> + - const: nss_port5_tx >> + - const: nss_port6_rx >> + - const: nss_port6_tx >> + - const: uniphy_port1_rx >> + - const: uniphy_port1_tx >> + - const: uniphy_port2_rx >> + - const: uniphy_port2_tx >> + - const: uniphy_port3_rx >> + - const: uniphy_port3_tx >> + - const: uniphy_port4_rx >> + - const: uniphy_port4_tx >> + - const: uniphy_port5_rx >> + - const: uniphy_port5_tx >> + - const: uniphy_port6_rx >> + - const: uniphy_port6_tx >> + - const: nss_port5_rx_clk_src >> + - const: nss_port5_tx_clk_src >> + >> + resets: >> + items: >> + - description: Reset PPE >> + - description: Reset uniphy0 software config >> + - description: Reset uniphy1 software config >> + - description: Reset uniphy2 software config >> + - description: Reset uniphy0 AHB >> + - description: Reset uniphy1 AHB >> + - description: Reset uniphy2 AHB >> + - description: Reset uniphy0 system >> + - description: Reset uniphy1 system >> + - description: Reset uniphy2 system >> + - description: Reset uniphy0 XPCS >> + - description: Reset uniphy1 XPCS >> + - description: Reset uniphy2 XPCS >> + - description: Assert uniphy port1 >> + - description: Assert uniphy port2 >> + - description: Assert uniphy port3 >> + - description: Assert uniphy port4 >> + - description: Reset PPE port1 >> + - description: Reset PPE port2 >> + - description: Reset PPE port3 >> + - description: Reset PPE port4 >> + - description: Reset PPE port5 >> + - description: Reset PPE port6 >> + - description: Reset PPE port1 MAC >> + - description: Reset PPE port2 MAC >> + - description: Reset PPE port3 MAC >> + - description: Reset PPE port4 MAC >> + - description: Reset PPE port5 MAC >> + - description: Reset PPE port6 MAC >> + >> + reset-names: >> + items: >> + - const: ppe >> + - const: uniphy0_soft >> + - const: uniphy1_soft >> + - const: uniphy2_soft >> + - const: uniphy0_ahb >> + - const: uniphy1_ahb >> + - const: uniphy2_ahb >> + - const: uniphy0_sys >> + - const: uniphy1_sys >> + - const: uniphy2_sys >> + - const: uniphy0_xpcs >> + - const: uniphy1_xpcs >> + - const: uniphy2_xpcs >> + - const: uniphy0_port1_dis >> + - const: uniphy0_port2_dis >> + - const: uniphy0_port3_dis >> + - const: uniphy0_port4_dis >> + - const: nss_port1 >> + - const: nss_port2 >> + - const: nss_port3 >> + - const: nss_port4 >> + - const: nss_port5 >> + - const: nss_port6 >> + - const: nss_port1_mac >> + - const: nss_port2_mac >> + - const: nss_port3_mac >> + - const: nss_port4_mac >> + - const: nss_port5_mac >> + - const: nss_port6_mac >> + >> +required: > > allOf: goes after required: Ok. > >> + - compatible >> + - reg >> + - "#address-cells" >> + - "#size-cells" >> + - ranges >> + - clocks >> + - clock-names >> + - resets >> + - reset-names >> + - tdm-config >> + - buffer-management-config >> + - queue-management-config >> + - port-scheduler-resource >> + - port-scheduler-config >> + >> +additionalProperties: false > > >> + >> +examples: >> + - | >> + #include <dt-bindings/clock/qcom,ipq9574-gcc.h> >> + #include <dt-bindings/reset/qcom,ipq9574-gcc.h> >> + #include <dt-bindings/clock/qcom,ipq9574-nsscc.h> >> + #include <dt-bindings/reset/qcom,ipq9574-nsscc.h> >> + >> + soc { >> + #address-cells = <1>; >> + #size-cells = <1>; >> + qcom_ppe: qcom-ppe@3a000000 { > > Drop label, Generic node names. Ok. We are trying to identify an appropriate generic name for the PPE from the device tree documentation, since it comprises of many hardware functions such as ethernet MAC and other packet processing blocks. We are planning to update the node name to a generic name 'ethernet'. > >> + compatible = "qcom,ipq9574-ppe"; > > Entire indentation of example is broken. Use one described in the > bindings coding style. will correct it, thanks for pointing out. > > Best regards, > Krzysztof >
> > > +++ b/Documentation/devicetree/bindings/net/qcom,ppe.yaml > > > @@ -0,0 +1,1330 @@ > > > +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/net/qcom,ppe.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: Qualcomm Packet Process Engine Ethernet controller > > > > Where is the ref to ethernet controllers schema? > Sorry, the title above is not describing the device for this dtbindings > correctly. It should say "Qualcomm Packet Process Engine". The > reference to the schema for PPE is mentioned above. I think you are not correctly understanding the comment. within the PPE you have a collection of Ethernet interfaces. All the common properties for Ethernet ports are described in Documentation/devicetree/bindings/net/ethernet-controller.yaml so you are expected to reference this schema. > > > +description: > > > + The PPE(packet process engine) is comprised of three componets, Ethernet > > > + DMA, Switch core and Port wrapper, Ethernet DMA is used to transmit and > > > + receive packets between Ethernet subsytem and host. The Switch core has > > > + maximum 8 ports(maximum 6 front panel ports and two FIFO interfaces), > > > + among which there are GMAC/XGMACs used as external interfaces and FIFO > > > + interfaces connected the EDMA/EIP, The port wrapper provides connections > > > + from the GMAC/XGMACS to SGMII/QSGMII/PSGMII/USXGMII/10G-BASER etc, there > > > + are maximu 3 UNIPHY(PCS) instances supported by PPE. I think a big part of the problem here is, you have a flat representation of the PPE. But device tree is very hierarchical. The hardware itself is also probably very hierarchical. Please spend some timer studying other DT descriptions of similar hardware. Then throw away this vendor crap DT binding and start again from scratch, with a hierarchical description of the hardware. Andrew
diff --git a/Documentation/devicetree/bindings/net/qcom,ppe.yaml b/Documentation/devicetree/bindings/net/qcom,ppe.yaml new file mode 100644 index 000000000000..6afb2ad62707 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom,ppe.yaml @@ -0,0 +1,1330 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qcom,ppe.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Packet Process Engine Ethernet controller + +maintainers: + - Luo Jie <quic_luoj@quicinc.com> + +description: + The PPE(packet process engine) is comprised of three componets, Ethernet + DMA, Switch core and Port wrapper, Ethernet DMA is used to transmit and + receive packets between Ethernet subsytem and host. The Switch core has + maximum 8 ports(maximum 6 front panel ports and two FIFO interfaces), + among which there are GMAC/XGMACs used as external interfaces and FIFO + interfaces connected the EDMA/EIP, The port wrapper provides connections + from the GMAC/XGMACS to SGMII/QSGMII/PSGMII/USXGMII/10G-BASER etc, there + are maximu 3 UNIPHY(PCS) instances supported by PPE. + +properties: + compatible: + enum: + - qcom,ipq5332-ppe + - qcom,ipq9574-ppe + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + ranges: true + + clocks: true + + clock-names: true + + resets: true + + reset-names: true + + tdm-config: + type: object + additionalProperties: false + description: | + PPE TDM(time-division multiplexing) config includes buffer management + and port scheduler. + + properties: + qcom,tdm-bm-config: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + The TDM buffer scheduler configs of PPE, there are multiple + entries supported, each entry includes valid, direction + (ingress or egress), port, second port valid, second port. + + qcom,tdm-port-scheduler-config: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + The TDM port scheduler management configs of PPE, there + are multiple entries supported each entry includes ingress + scheduler port bitmap, ingress scheduler port, egress + scheduler port, second egress scheduler port valid and + second egress scheduler port. + + required: + - qcom,tdm-bm-config + - qcom,tdm-port-scheduler-config + + buffer-management-config: + type: object + additionalProperties: false + description: | + PPE buffer management config, which supports configuring group + buffer and per port buffer, which decides the threshold of the + flow control frame generated. + + properties: + qcom,group-config: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + The PPE buffer support 4 groups, the entry includes + the group ID and group buffer numbers, each buffer + has 256 bytes. + + qcom,port-config: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + The PPE buffer number is also assigned per BM port ID, + there are 10 BM ports supported on ipq5332, and 15 BM + ports supported on ipq9574. Each entry includs group + ID, BM port ID, dedicated buffer, the buffer numbers + for receiving packet after pause frame sent, the + threshold for pause frame, weight, restore ceil and + dynamic buffer or static buffer management. + + required: + - qcom,group-config + - qcom,port-config + + queue-management-config: + type: object + additionalProperties: false + description: | + PPE queue management config, which supports configuring group + and per queue buffer limitation, which decides the threshold + to drop the packet on the egress port. + + properties: + qcom,group-config: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + The PPE queue management support 4 groups, the entry + includes the group ID, group buffer number, dedicated + buffer number, threshold to drop packet and restore + ceil. + + qcom,queue-config: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + PPE has 256 unicast queues and 44 multicast queues, the + entry includes queue base, queue number, group ID, + dedicated buffer, the threshold to drop packet, weight, + restore ceil and dynamic or static queue management. + + required: + - qcom,group-config + - qcom,queue-config + + port-scheduler-resource: + type: object + additionalProperties: false + description: The scheduler resource available in PPE. + patternProperties: + "^port[0-7]$": + description: Each subnode represents the scheduler resource per port. + type: object + properties: + port-id: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The PPE port ID, there are maximum 6 physical port, + EIP port and CPU port. + + qcom,ucast-queue: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: The PPE unicast queue range. + + qcom,mcast-queue: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: The PPE multicast queue range. + + qcom,l0sp: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: The PPE L0 strict priority scheduler range. + + qcom,l0cdrr: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: The PPE L0 promise DRR range. + + qcom,l0edrr: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: The PPE L0 exceed DRR range. + + qcom,l1cdrr: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: The PPE L1 promise DRR range. + + qcom,l1edrr: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: The PPE L1 exceed DRR range. + + required: + - port-id + - qcom,ucast-queue + - qcom,mcast-queue + - qcom,l0sp + - qcom,l0cdrr + - qcom,l0edrr + - qcom,l1cdrr + - qcom,l1edrr + + port-scheduler-config: + type: object + additionalProperties: false + description: The scheduler resource config in PPE. + patternProperties: + "^port[0-7]$": + type: object + additionalProperties: false + description: Each subnode represents the scheduler config per port. + properties: + port-id: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The PPE port ID, there are maximum 6 physical port + and one CPU port. + + l1scheduler: + type: object + additionalProperties: false + description: PPE port level 1 scheduler config + patternProperties: + "^group[0-7]$": + type: object + additionalProperties: false + description: PPE per flow scheduler config in level 1 + properties: + qcom,flow: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The flow ID for level 1 scheduler + + qcom,flow-loop-priority: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The flow loop priority for level 1 scheduler + + qcom,scheduler-config: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 5 + maxItems: 5 + description: | + The scheduler config includes flow ID, promise priority, + promise DRR, exceed priority and exceed DRR. + + required: + - qcom,flow + - qcom,scheduler-config + + l0scheduler: + type: object + additionalProperties: false + description: PPE port level 0 scheduler config + patternProperties: + "^group[0-7]$": + type: object + additionalProperties: false + description: PPE per flow scheduler config in level 0 + properties: + qcom,ucast-queue: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The unicast queue base ID. + + qcom,mcast-queue: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The multicast queue base ID. + + qcom,ucast-loop-priority: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The unicast priority number, each priority has dedicated + queue. + + qcom,mcast-loop-priority: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The multicast priority number, each priority has dedicated + queue. + + qcom,drr-max-priority: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The unicast maximum priority for the configured queues + + qcom,scheduler-config: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 5 + maxItems: 5 + description: + The flow ID input to level 1 scheduler, promise priority, + promise DRR, exceed priority and exceed DRR. + + required: + - qcom,ucast-queue + - qcom,mcast-queue + - qcom,scheduler-config + + required: + - port-id + - l0scheduler + - l1scheduler + +patternProperties: + "^qcom-uniphy@[0-9a-f]+$": + type: object + additionalProperties: false + description: uniphy configuration and clock provider + properties: + reg: + minItems: 2 + items: + - description: The first uniphy register range + - description: The second uniphy register range + - description: The third uniphy register range + + "#clock-cells": + const: 1 + + clock-output-names: + minItems: 4 + maxItems: 6 + + required: + - reg + - "#clock-cells" + - clock-output-names + +allOf: + - if: + properties: + compatible: + contains: + const: qcom,ipq5332-ppe + then: + properties: + clocks: + items: + - description: Display common AHB clock from gcc + - description: Display common system clock from gcc + - description: Display uniphy0 AHB clock from gcc + - description: Display uniphy1 AHB clock from gcc + - description: Display uniphy0 system clock from gcc + - description: Display uniphy1 system clock from gcc + - description: Display nss clock from gcc + - description: Display nss noc snoc clock from gcc + - description: Display nss noc snoc_1 clock from gcc + - description: Display sleep clock from gcc + - description: Display PPE clock from nsscc + - description: Display PPE config clock from nsscc + - description: Display NSSNOC PPE clock from nsscc + - description: Display NSSNOC PPE config clock from nsscc + - description: Display EDMA clock from nsscc + - description: Display EDMA config clock from nsscc + - description: Display PPE IPE clock from nsscc + - description: Display PPE BTQ clock from nsscc + - description: Display port1 MAC clock from nsscc + - description: Display port2 MAC clock from nsscc + - description: Display port1 RX clock from nsscc + - description: Display port1 TX clock from nsscc + - description: Display port2 RX clock from nsscc + - description: Display port2 TX clock from nsscc + - description: Display UNIPHY port1 RX clock from nsscc + - description: Display UNIPHY port1 TX clock from nsscc + - description: Display UNIPHY port2 RX clock from nsscc + - description: Display UNIPHY port2 TX clock from nsscc + clock-names: + items: + - const: cmn_ahb + - const: cmn_sys + - const: uniphy0_ahb + - const: uniphy1_ahb + - const: uniphy0_sys + - const: uniphy1_sys + - const: gcc_nsscc + - const: gcc_nssnoc_snoc + - const: gcc_nssnoc_snoc_1 + - const: gcc_im_sleep + - const: nss_ppe + - const: nss_ppe_cfg + - const: nssnoc_ppe + - const: nssnoc_ppe_cfg + - const: nss_edma + - const: nss_edma_cfg + - const: nss_ppe_ipe + - const: nss_ppe_btq + - const: port1_mac + - const: port2_mac + - const: nss_port1_rx + - const: nss_port1_tx + - const: nss_port2_rx + - const: nss_port2_tx + - const: uniphy_port1_rx + - const: uniphy_port1_tx + - const: uniphy_port2_rx + - const: uniphy_port2_tx + + resets: + items: + - description: Reset PPE + - description: Reset uniphy0 software config + - description: Reset uniphy1 software config + - description: Reset uniphy0 AHB + - description: Reset uniphy1 AHB + - description: Reset uniphy0 system + - description: Reset uniphy1 system + - description: Reset uniphy0 XPCS + - description: Reset uniphy1 SPCS + - description: Reset uniphy port1 RX + - description: Reset uniphy port1 TX + - description: Reset uniphy port2 RX + - description: Reset uniphy port2 TX + - description: Reset PPE port1 RX + - description: Reset PPE port1 TX + - description: Reset PPE port2 RX + - description: Reset PPE port2 TX + - description: Reset PPE port1 MAC + - description: Reset PPE port2 MAC + + reset-names: + items: + - const: ppe + - const: uniphy0_soft + - const: uniphy1_soft + - const: uniphy0_ahb + - const: uniphy1_ahb + - const: uniphy0_sys + - const: uniphy1_sys + - const: uniphy0_xpcs + - const: uniphy1_xpcs + - const: uniphy_port1_rx + - const: uniphy_port1_tx + - const: uniphy_port2_rx + - const: uniphy_port2_tx + - const: nss_port1_rx + - const: nss_port1_tx + - const: nss_port2_rx + - const: nss_port2_tx + - const: nss_port1_mac + - const: nss_port2_mac + + - if: + properties: + compatible: + contains: + const: qcom,ipq9574-ppe + then: + properties: + clocks: + items: + - description: Display common AHB clock from gcc + - description: Display common system clock from gcc + - description: Display uniphy0 AHB clock from gcc + - description: Display uniphy1 AHB clock from gcc + - description: Display uniphy2 AHB clock from gcc + - description: Display uniphy0 system clock from gcc + - description: Display uniphy1 system clock from gcc + - description: Display uniphy2 system clock from gcc + - description: Display nss clock from gcc + - description: Display nss noc clock from gcc + - description: Display nss noc snoc clock from gcc + - description: Display nss noc snoc_1 clock from gcc + - description: Display PPE clock from nsscc + - description: Display PPE config clock from nsscc + - description: Display NSSNOC PPE clock from nsscc + - description: Display NSSNOC PPE config clock from nsscc + - description: Display EDMA clock from nsscc + - description: Display EDMA config clock from nsscc + - description: Display PPE IPE clock from nsscc + - description: Display PPE BTQ clock from nsscc + - description: Display port1 MAC clock from nsscc + - description: Display port2 MAC clock from nsscc + - description: Display port3 MAC clock from nsscc + - description: Display port4 MAC clock from nsscc + - description: Display port5 MAC clock from nsscc + - description: Display port6 MAC clock from nsscc + - description: Display port1 RX clock from nsscc + - description: Display port1 TX clock from nsscc + - description: Display port2 RX clock from nsscc + - description: Display port2 TX clock from nsscc + - description: Display port3 RX clock from nsscc + - description: Display port3 TX clock from nsscc + - description: Display port4 RX clock from nsscc + - description: Display port4 TX clock from nsscc + - description: Display port5 RX clock from nsscc + - description: Display port5 TX clock from nsscc + - description: Display port6 RX clock from nsscc + - description: Display port6 TX clock from nsscc + - description: Display UNIPHY port1 RX clock from nsscc + - description: Display UNIPHY port1 TX clock from nsscc + - description: Display UNIPHY port2 RX clock from nsscc + - description: Display UNIPHY port2 TX clock from nsscc + - description: Display UNIPHY port3 RX clock from nsscc + - description: Display UNIPHY port3 TX clock from nsscc + - description: Display UNIPHY port4 RX clock from nsscc + - description: Display UNIPHY port4 TX clock from nsscc + - description: Display UNIPHY port5 RX clock from nsscc + - description: Display UNIPHY port5 TX clock from nsscc + - description: Display UNIPHY port6 RX clock from nsscc + - description: Display UNIPHY port6 TX clock from nsscc + - description: Display port5 RX clock source from nsscc + - description: Display port5 TX clock source from nsscc + clock-names: + items: + - const: cmn_ahb + - const: cmn_sys + - const: uniphy0_ahb + - const: uniphy1_ahb + - const: uniphy2_ahb + - const: uniphy0_sys + - const: uniphy1_sys + - const: uniphy2_sys + - const: gcc_nsscc + - const: gcc_nssnoc_nsscc + - const: gcc_nssnoc_snoc + - const: gcc_nssnoc_snoc_1 + - const: nss_ppe + - const: nss_ppe_cfg + - const: nssnoc_ppe + - const: nssnoc_ppe_cfg + - const: nss_edma + - const: nss_edma_cfg + - const: nss_ppe_ipe + - const: nss_ppe_btq + - const: port1_mac + - const: port2_mac + - const: port3_mac + - const: port4_mac + - const: port5_mac + - const: port6_mac + - const: nss_port1_rx + - const: nss_port1_tx + - const: nss_port2_rx + - const: nss_port2_tx + - const: nss_port3_rx + - const: nss_port3_tx + - const: nss_port4_rx + - const: nss_port4_tx + - const: nss_port5_rx + - const: nss_port5_tx + - const: nss_port6_rx + - const: nss_port6_tx + - const: uniphy_port1_rx + - const: uniphy_port1_tx + - const: uniphy_port2_rx + - const: uniphy_port2_tx + - const: uniphy_port3_rx + - const: uniphy_port3_tx + - const: uniphy_port4_rx + - const: uniphy_port4_tx + - const: uniphy_port5_rx + - const: uniphy_port5_tx + - const: uniphy_port6_rx + - const: uniphy_port6_tx + - const: nss_port5_rx_clk_src + - const: nss_port5_tx_clk_src + + resets: + items: + - description: Reset PPE + - description: Reset uniphy0 software config + - description: Reset uniphy1 software config + - description: Reset uniphy2 software config + - description: Reset uniphy0 AHB + - description: Reset uniphy1 AHB + - description: Reset uniphy2 AHB + - description: Reset uniphy0 system + - description: Reset uniphy1 system + - description: Reset uniphy2 system + - description: Reset uniphy0 XPCS + - description: Reset uniphy1 XPCS + - description: Reset uniphy2 XPCS + - description: Assert uniphy port1 + - description: Assert uniphy port2 + - description: Assert uniphy port3 + - description: Assert uniphy port4 + - description: Reset PPE port1 + - description: Reset PPE port2 + - description: Reset PPE port3 + - description: Reset PPE port4 + - description: Reset PPE port5 + - description: Reset PPE port6 + - description: Reset PPE port1 MAC + - description: Reset PPE port2 MAC + - description: Reset PPE port3 MAC + - description: Reset PPE port4 MAC + - description: Reset PPE port5 MAC + - description: Reset PPE port6 MAC + + reset-names: + items: + - const: ppe + - const: uniphy0_soft + - const: uniphy1_soft + - const: uniphy2_soft + - const: uniphy0_ahb + - const: uniphy1_ahb + - const: uniphy2_ahb + - const: uniphy0_sys + - const: uniphy1_sys + - const: uniphy2_sys + - const: uniphy0_xpcs + - const: uniphy1_xpcs + - const: uniphy2_xpcs + - const: uniphy0_port1_dis + - const: uniphy0_port2_dis + - const: uniphy0_port3_dis + - const: uniphy0_port4_dis + - const: nss_port1 + - const: nss_port2 + - const: nss_port3 + - const: nss_port4 + - const: nss_port5 + - const: nss_port6 + - const: nss_port1_mac + - const: nss_port2_mac + - const: nss_port3_mac + - const: nss_port4_mac + - const: nss_port5_mac + - const: nss_port6_mac + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - ranges + - clocks + - clock-names + - resets + - reset-names + - tdm-config + - buffer-management-config + - queue-management-config + - port-scheduler-resource + - port-scheduler-config + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,ipq9574-gcc.h> + #include <dt-bindings/reset/qcom,ipq9574-gcc.h> + #include <dt-bindings/clock/qcom,ipq9574-nsscc.h> + #include <dt-bindings/reset/qcom,ipq9574-nsscc.h> + + soc { + #address-cells = <1>; + #size-cells = <1>; + qcom_ppe: qcom-ppe@3a000000 { + compatible = "qcom,ipq9574-ppe"; + reg = <0x3a000000 0xb00000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + clocks = <&gcc GCC_CMN_12GPLL_AHB_CLK>, + <&gcc GCC_CMN_12GPLL_SYS_CLK>, + <&gcc GCC_UNIPHY0_AHB_CLK>, + <&gcc GCC_UNIPHY1_AHB_CLK>, + <&gcc GCC_UNIPHY2_AHB_CLK>, + <&gcc GCC_UNIPHY0_SYS_CLK>, + <&gcc GCC_UNIPHY1_SYS_CLK>, + <&gcc GCC_UNIPHY2_SYS_CLK>, + <&gcc GCC_NSSCC_CLK>, + <&gcc GCC_NSSNOC_NSSCC_CLK>, + <&gcc GCC_NSSNOC_SNOC_CLK>, + <&gcc GCC_NSSNOC_SNOC_1_CLK>, + <&nsscc NSS_CC_PPE_SWITCH_CLK>, + <&nsscc NSS_CC_PPE_SWITCH_CFG_CLK>, + <&nsscc NSS_CC_NSSNOC_PPE_CLK>, + <&nsscc NSS_CC_NSSNOC_PPE_CFG_CLK>, + <&nsscc NSS_CC_PPE_EDMA_CLK>, + <&nsscc NSS_CC_PPE_EDMA_CFG_CLK>, + <&nsscc NSS_CC_PPE_SWITCH_IPE_CLK>, + <&nsscc NSS_CC_PPE_SWITCH_BTQ_CLK>, + <&nsscc NSS_CC_PORT1_MAC_CLK>, + <&nsscc NSS_CC_PORT2_MAC_CLK>, + <&nsscc NSS_CC_PORT3_MAC_CLK>, + <&nsscc NSS_CC_PORT4_MAC_CLK>, + <&nsscc NSS_CC_PORT5_MAC_CLK>, + <&nsscc NSS_CC_PORT6_MAC_CLK>, + <&nsscc NSS_CC_PORT1_RX_CLK>, + <&nsscc NSS_CC_PORT1_TX_CLK>, + <&nsscc NSS_CC_PORT2_RX_CLK>, + <&nsscc NSS_CC_PORT2_TX_CLK>, + <&nsscc NSS_CC_PORT3_RX_CLK>, + <&nsscc NSS_CC_PORT3_TX_CLK>, + <&nsscc NSS_CC_PORT4_RX_CLK>, + <&nsscc NSS_CC_PORT4_TX_CLK>, + <&nsscc NSS_CC_PORT5_RX_CLK>, + <&nsscc NSS_CC_PORT5_TX_CLK>, + <&nsscc NSS_CC_PORT6_RX_CLK>, + <&nsscc NSS_CC_PORT6_TX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT1_RX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT1_TX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT2_RX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT2_TX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT3_RX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT3_TX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT4_RX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT4_TX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT5_RX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT5_TX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT6_RX_CLK>, + <&nsscc NSS_CC_UNIPHY_PORT6_TX_CLK>, + <&nsscc NSS_CC_PORT5_RX_CLK_SRC>, + <&nsscc NSS_CC_PORT5_TX_CLK_SRC>; + clock-names = "cmn_ahb", + "cmn_sys", + "uniphy0_ahb", + "uniphy1_ahb", + "uniphy2_ahb", + "uniphy0_sys", + "uniphy1_sys", + "uniphy2_sys", + "gcc_nsscc", + "gcc_nssnoc_nsscc", + "gcc_nssnoc_snoc", + "gcc_nssnoc_snoc_1", + "nss_ppe", + "nss_ppe_cfg", + "nssnoc_ppe", + "nssnoc_ppe_cfg", + "nss_edma", + "nss_edma_cfg", + "nss_ppe_ipe", + "nss_ppe_btq", + "port1_mac", + "port2_mac", + "port3_mac", + "port4_mac", + "port5_mac", + "port6_mac", + "nss_port1_rx", + "nss_port1_tx", + "nss_port2_rx", + "nss_port2_tx", + "nss_port3_rx", + "nss_port3_tx", + "nss_port4_rx", + "nss_port4_tx", + "nss_port5_rx", + "nss_port5_tx", + "nss_port6_rx", + "nss_port6_tx", + "uniphy_port1_rx", + "uniphy_port1_tx", + "uniphy_port2_rx", + "uniphy_port2_tx", + "uniphy_port3_rx", + "uniphy_port3_tx", + "uniphy_port4_rx", + "uniphy_port4_tx", + "uniphy_port5_rx", + "uniphy_port5_tx", + "uniphy_port6_rx", + "uniphy_port6_tx", + "nss_port5_rx_clk_src", + "nss_port5_tx_clk_src"; + resets = <&nsscc PPE_FULL_RESET>, + <&nsscc UNIPHY0_SOFT_RESET>, + <&nsscc UNIPHY_PORT5_ARES>, + <&nsscc UNIPHY_PORT6_ARES>, + <&gcc GCC_UNIPHY0_AHB_RESET>, + <&gcc GCC_UNIPHY1_AHB_RESET>, + <&gcc GCC_UNIPHY2_AHB_RESET>, + <&gcc GCC_UNIPHY0_SYS_RESET>, + <&gcc GCC_UNIPHY1_SYS_RESET>, + <&gcc GCC_UNIPHY2_SYS_RESET>, + <&gcc GCC_UNIPHY0_XPCS_RESET>, + <&gcc GCC_UNIPHY1_XPCS_RESET>, + <&gcc GCC_UNIPHY2_XPCS_RESET>, + <&nsscc UNIPHY_PORT1_ARES>, + <&nsscc UNIPHY_PORT2_ARES>, + <&nsscc UNIPHY_PORT3_ARES>, + <&nsscc UNIPHY_PORT4_ARES>, + <&nsscc NSSPORT1_RESET>, + <&nsscc NSSPORT2_RESET>, + <&nsscc NSSPORT3_RESET>, + <&nsscc NSSPORT4_RESET>, + <&nsscc NSSPORT5_RESET>, + <&nsscc NSSPORT6_RESET>, + <&nsscc PORT1_MAC_ARES>, + <&nsscc PORT2_MAC_ARES>, + <&nsscc PORT3_MAC_ARES>, + <&nsscc PORT4_MAC_ARES>, + <&nsscc PORT5_MAC_ARES>, + <&nsscc PORT6_MAC_ARES>; + reset-names = "ppe", + "uniphy0_soft", + "uniphy1_soft", + "uniphy2_soft", + "uniphy0_ahb", + "uniphy1_ahb", + "uniphy2_ahb", + "uniphy0_sys", + "uniphy1_sys", + "uniphy2_sys", + "uniphy0_xpcs", + "uniphy1_xpcs", + "uniphy2_xpcs", + "uniphy0_port1_dis", + "uniphy0_port2_dis", + "uniphy0_port3_dis", + "uniphy0_port4_dis", + "nss_port1", + "nss_port2", + "nss_port3", + "nss_port4", + "nss_port5", + "nss_port6", + "nss_port1_mac", + "nss_port2_mac", + "nss_port3_mac", + "nss_port4_mac", + "nss_port5_mac", + "nss_port6_mac"; + + uniphys: qcom-uniphy@7a00000 { + reg = <0x7a00000 0x10000>, + <0x7a10000 0x10000>, + <0x7a20000 0x10000>; + #clock-cells = <0x1>; + clock-output-names = "uniphy0_gcc_rx_clk", + "uniphy0_gcc_tx_clk", + "uniphy1_gcc_rx_clk", + "uniphy1_gcc_tx_clk", + "uniphy2_gcc_rx_clk", + "uniphy2_gcc_tx_clk"; + }; + + tdm-config { + qcom,tdm-bm-config = <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 1 0 0>, + <1 1 1 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 7 0 0>, + <1 1 7 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 1 0 0>, + <1 1 1 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 2 0 0>, + <1 1 2 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 1 0 0>, + <1 1 1 0 0>, + <1 0 3 0 0>, + <1 1 3 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 7 0 0>, + <1 1 7 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 1 0 0>, + <1 1 1 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 4 0 0>, + <1 1 4 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 1 0 0>, + <1 1 1 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 2 0 0>, + <1 1 2 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 7 0 0>, + <1 1 7 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 1 0 0>, + <1 1 1 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 3 0 0>, + <1 1 3 0 0>, + <1 0 1 0 0>, + <1 1 1 0 0>, + <1 0 0 0 0>, + <1 1 0 0 0>, + <1 0 5 0 0>, + <1 1 5 0 0>, + <1 0 6 0 0>, + <1 1 6 0 0>, + <1 0 4 0 0>, + <1 1 4 0 0>, + <1 0 7 0 0>, + <1 1 7 0 0>; + qcom,tdm-port-scheduler-config = <0x98 6 0 1 1>, + <0x94 5 6 1 3>, + <0x86 0 5 1 4>, + <0x8C 1 6 1 0>, + <0x1C 7 5 1 1>, + <0x98 2 6 1 0>, + <0x1C 5 7 1 1>, + <0x34 3 6 1 0>, + <0x8C 4 5 1 1>, + <0x98 2 6 1 0>, + <0x8C 5 4 1 1>, + <0xA8 0 6 1 2>, + <0x98 5 1 1 0>, + <0x98 6 5 1 2>, + <0x89 1 6 1 4>, + <0xA4 3 0 1 1>, + <0x8C 5 6 1 4>, + <0xA8 0 2 1 1>, + <0x98 6 5 1 0>, + <0xC4 4 3 1 1>, + <0x94 6 5 1 0>, + <0x1C 7 6 1 1>, + <0x98 2 5 1 0>, + <0x1C 6 7 1 1>, + <0x1C 5 6 1 0>, + <0x94 3 5 1 1>, + <0x8C 4 6 1 0>, + <0x94 1 5 1 3>, + <0x94 6 1 1 0>, + <0xD0 3 5 1 2>, + <0x98 6 0 1 1>, + <0x94 5 6 1 3>, + <0x94 1 5 1 0>, + <0x98 2 6 1 1>, + <0x8C 4 5 1 0>, + <0x1C 7 6 1 1>, + <0x8C 0 5 1 4>, + <0x89 1 6 1 2>, + <0x98 5 0 1 1>, + <0x94 6 5 1 3>, + <0x92 0 6 1 2>, + <0x98 1 5 1 0>, + <0x98 6 2 1 1>, + <0xD0 0 5 1 3>, + <0x94 6 0 1 1>, + <0x8C 5 6 1 4>, + <0x8C 1 5 1 0>, + <0x1C 6 7 1 1>, + <0x1C 5 6 1 0>, + <0xB0 2 3 1 1>, + <0xC4 4 5 1 0>, + <0x8C 6 4 1 1>, + <0xA4 3 6 1 0>, + <0x1C 5 7 1 1>, + <0x4C 0 5 1 4>, + <0x8C 6 0 1 1>, + <0x34 7 6 1 3>, + <0x94 5 0 1 1>, + <0x98 6 5 1 2>; + }; + + buffer-management-config { + qcom,group-config = <0 1550>; + qcom,port-config = <0 0 0 100 1146 7 8 0 1>, + <0 1 0 100 250 4 36 0 1>, + <0 2 0 100 250 4 36 0 1>, + <0 3 0 100 250 4 36 0 1>, + <0 4 0 100 250 4 36 0 1>, + <0 5 0 100 250 4 36 0 1>, + <0 6 0 100 250 4 36 0 1>, + <0 7 0 100 250 4 36 0 1>, + <0 8 0 128 250 4 36 0 1>, + <0 9 0 128 250 4 36 0 1>, + <0 10 0 128 250 4 36 0 1>, + <0 11 0 128 250 4 36 0 1>, + <0 12 0 128 250 4 36 0 1>, + <0 13 0 128 250 4 36 0 1>, + <0 14 0 40 250 4 36 0 1>; + }; + + queue-management-config { + qcom,group-config = <0 2000 0 0 0>; + qcom,queue-config = <0 256 0 0 400 4 36 1>, + <256 44 0 0 250 0 36 0>; + }; + + port-scheduler-resource { + port0 { + port-id = <0>; + qcom,ucast-queue = <0 63>; + qcom,mcast-queue = <256 263>; + qcom,l0sp = <0 0>; + qcom,l0cdrr = <0 7>; + qcom,l0edrr = <0 7>; + qcom,l1cdrr = <0 0>; + qcom,l1edrr = <0 0>; + }; + + port1 { + port-id = <1>; + qcom,ucast-queue = <204 211>; + qcom,mcast-queue = <272 275>; + qcom,l0sp = <51 52>; + qcom,l0cdrr = <108 115>; + qcom,l0edrr = <108 115>; + qcom,l1cdrr = <23 24>; + qcom,l1edrr = <23 24>; + }; + + port2 { + port-id = <2>; + qcom,ucast-queue = <212 219>; + qcom,mcast-queue = <276 279>; + qcom,l0sp = <53 54>; + qcom,l0cdrr = <116 123>; + qcom,l0edrr = <116 123>; + qcom,l1cdrr = <25 26>; + qcom,l1edrr = <25 26>; + }; + + port3 { + port-id = <3>; + qcom,ucast-queue = <220 227>; + qcom,mcast-queue = <280 283>; + qcom,l0sp = <55 56>; + qcom,l0cdrr = <124 131>; + qcom,l0edrr = <124 131>; + qcom,l1cdrr = <27 28>; + qcom,l1edrr = <27 28>; + }; + + port4 { + port-id = <4>; + qcom,ucast-queue = <228 235>; + qcom,mcast-queue = <284 287>; + qcom,l0sp = <57 58>; + qcom,l0cdrr = <132 139>; + qcom,l0edrr = <132 139>; + qcom,l1cdrr = <29 30>; + qcom,l1edrr = <29 30>; + }; + + port5 { + port-id = <5>; + qcom,ucast-queue = <236 243>; + qcom,mcast-queue = <288 291>; + qcom,l0sp = <59 60>; + qcom,l0cdrr = <140 147>; + qcom,l0edrr = <140 147>; + qcom,l1cdrr = <31 32>; + qcom,l1edrr = <31 32>; + }; + + port6 { + port-id = <6>; + qcom,ucast-queue = <244 251>; + qcom,mcast-queue = <292 295>; + qcom,l0sp = <61 62>; + qcom,l0cdrr = <148 155>; + qcom,l0edrr = <148 155>; + qcom,l1cdrr = <33 34>; + qcom,l1edrr = <33 34>; + }; + + port7 { + port-id = <7>; + qcom,ucast-queue = <252 255>; + qcom,mcast-queue = <296 299>; + qcom,l0sp = <63 63>; + qcom,l0cdrr = <156 159>; + qcom,l0edrr = <156 159>; + qcom,l1cdrr = <35 35>; + qcom,l1edrr = <35 35>; + }; + }; + + port-scheduler-config { + port0 { + port-id = <0>; + l1scheduler { + group0 { + qcom,flow = <0>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + }; + + l0scheduler { + group0 { + qcom,ucast-queue = <0>; + qcom,ucast-loop-priority = <8>; + qcom,mcast-queue = <256>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + + group1 { + qcom,ucast-queue = <8>; + qcom,ucast-loop-priority = <8>; + qcom,mcast-queue = <257>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + + group2 { + qcom,ucast-queue = <16>; + qcom,ucast-loop-priority = <8>; + qcom,mcast-queue = <258>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + + group3 { + qcom,ucast-queue = <24>; + qcom,ucast-loop-priority = <8>; + qcom,mcast-queue = <259>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + + group4 { + qcom,ucast-queue = <32>; + qcom,ucast-loop-priority = <8>; + qcom,mcast-queue = <260>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + + group5 { + qcom,ucast-queue = <40>; + qcom,ucast-loop-priority = <8>; + qcom,mcast-queue = <261>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + + group6 { + qcom,ucast-queue = <48>; + qcom,ucast-loop-priority = <8>; + qcom,mcast-queue = <262>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + + group7 { + qcom,ucast-queue = <56>; + qcom,ucast-loop-priority = <8>; + qcom,mcast-queue = <263>; + qcom,scheduler-config = <0 0 0 0 0>; + }; + }; + }; + + port1 { + port-id = <1>; + l1scheduler { + group0 { + qcom,flow = <51>; + qcom,flow-loop-priority = <2>; + qcom,scheduler-config = <1 0 23 0 23>; + }; + }; + + l0scheduler { + group0 { + qcom,ucast-queue = <204>; + qcom,ucast-loop-priority = <8>; + qcom,drr-max-priority = <4>; + qcom,mcast-queue = <272>; + qcom,mcast-loop-priority = <4>; + qcom,scheduler-config = <51 0 108 0 108>; + }; + }; + }; + + port2 { + port-id = <2>; + l1scheduler { + group0 { + qcom,flow = <53>; + qcom,flow-loop-priority = <2>; + qcom,scheduler-config = <2 0 25 0 25>; + }; + }; + + l0scheduler { + group0 { + qcom,ucast-queue = <212>; + qcom,ucast-loop-priority = <8>; + qcom,drr-max-priority = <4>; + qcom,mcast-queue = <276>; + qcom,mcast-loop-priority = <4>; + qcom,scheduler-config = <53 0 116 0 116>; + }; + }; + }; + + port3 { + port-id = <3>; + l1scheduler { + group0 { + qcom,flow = <55>; + qcom,flow-loop-priority = <2>; + qcom,scheduler-config = <3 0 27 0 27>; + }; + }; + + l0scheduler { + group0 { + qcom,ucast-queue = <220>; + qcom,ucast-loop-priority = <8>; + qcom,drr-max-priority = <4>; + qcom,mcast-queue = <280>; + qcom,mcast-loop-priority = <4>; + qcom,scheduler-config = <55 0 124 0 124>; + }; + }; + }; + + port4 { + port-id = <4>; + l1scheduler { + group0 { + qcom,flow = <57>; + qcom,flow-loop-priority = <2>; + qcom,scheduler-config = <4 0 29 0 29>; + }; + }; + + l0scheduler { + group0 { + qcom,ucast-queue = <228>; + qcom,ucast-loop-priority = <8>; + qcom,drr-max-priority = <4>; + qcom,mcast-queue = <284>; + qcom,mcast-loop-priority = <4>; + qcom,scheduler-config = <57 0 132 0 132>; + }; + }; + }; + + port5 { + port-id = <5>; + l1scheduler { + group0 { + qcom,flow = <59>; + qcom,flow-loop-priority = <2>; + qcom,scheduler-config = <5 0 31 0 31>; + }; + }; + + l0scheduler { + group0 { + qcom,ucast-queue = <236>; + qcom,ucast-loop-priority = <8>; + qcom,drr-max-priority = <4>; + qcom,mcast-queue = <288>; + qcom,mcast-loop-priority = <4>; + qcom,scheduler-config = <59 0 140 0 140>; + }; + }; + }; + + port6 { + port-id = <6>; + l1scheduler { + group0 { + qcom,flow = <61>; + qcom,flow-loop-priority = <2>; + qcom,scheduler-config = <6 0 33 0 33>; + }; + }; + + l0scheduler { + group0 { + qcom,ucast-queue = <244>; + qcom,ucast-loop-priority = <8>; + qcom,drr-max-priority = <4>; + qcom,mcast-queue = <292>; + qcom,mcast-loop-priority = <4>; + qcom,scheduler-config = <61 0 148 0 148>; + }; + }; + }; + + port7 { + port-id = <7>; + l1scheduler { + group0 { + qcom,flow = <63>; + qcom,scheduler-config = <7 0 35 0 35>; + }; + }; + + l0scheduler { + group0 { + qcom,ucast-queue = <252>; + qcom,ucast-loop-priority = <4>; + qcom,mcast-queue = <296>; + qcom,mcast-loop-priority = <4>; + qcom,scheduler-config = <63 0 156 0 156>; + }; + }; + }; + }; + }; + };
Qualcomm PPE(packet process engine) is supported on IPQ SOC platform. Signed-off-by: Luo Jie <quic_luoj@quicinc.com> --- .../devicetree/bindings/net/qcom,ppe.yaml | 1330 +++++++++++++++++ 1 file changed, 1330 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/qcom,ppe.yaml