| Message ID | 20240123-topic-sm8550-upstream-hdk8550-v2-2-99fba09fbfda@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: qcom: sm8550: add support for the SM8550-HDK board | expand |
On Tue, 23 Jan 2024 at 10:56, Neil Armstrong <neil.armstrong@linaro.org> wrote: > > The SM8550-HDK is an embedded development platforms for the > Snapdragon 8 Gen 2 SoC aka SM8550, with the following features: > - Qualcomm SM8550 SoC > - 16GiB On-board LPDDR5 > - On-board WiFi 7 + Bluetooth 5.3/BLE > - On-board UFS4.0 > - M.2 Key B+M Gen3x2 PCIe Slot > - HDMI Output > - USB-C Connector with DP Almode & Audio Accessory mode > - Micro-SDCard Slot > - Audio Jack with Playback and Microphone > - 2 On-board Analog microphones > - 2 On-board Speakers > - 96Boards Compatible Low-Speed and High-Speed connectors [1] > - For Camera, Sensors and external Display cards > - Compatible with the Linaro Debug board [2] > - SIM Slot for Modem > - Debug connectors > - 6x On-Board LEDs > > Product Page: [3] > > [1] https://www.96boards.org/specifications/ > [2] https://git.codelinaro.org/linaro/qcomlt/debugboard > [3] https://www.lantronix.com/products/snapdragon-8-gen-2-mobile-hardware-development-kit/ > > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/sm8550-hdk.dts | 1290 +++++++++++++++++++++++++++++++ > 2 files changed, 1291 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 39889d5f8e12..42e50f2b2ec3 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -233,6 +233,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-hdk.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8450-qrd.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx223.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb > +dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb > diff --git a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts > new file mode 100644 > index 000000000000..66bdd6c269ea > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts > @@ -0,0 +1,1290 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2024 Linaro Limited > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include "sm8550.dtsi" > +#include "pm8010.dtsi" > +#include "pm8550.dtsi" > +#include "pm8550b.dtsi" > +#define PMK8550VE_SID 5 Maybe the define should be moved before all include files and separated with the blank line? > +#include "pm8550ve.dtsi" > +#include "pm8550vs.dtsi" > +#include "pmk8550.dtsi" > +#include "pmr735d_a.dtsi" > + > +/ { > + model = "Qualcomm Technologies, Inc. SM8550 HDK"; > + compatible = "qcom,sm8550-hdk", "qcom,sm8550"; > + chassis-type = "embedded"; > + > + aliases { > + serial0 = &uart7; > + serial1 = &uart14; > + }; > + > + wcd938x: audio-codec { > + compatible = "qcom,wcd9385-codec"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&wcd_default>; > + > + qcom,micbias1-microvolt = <1800000>; > + qcom,micbias2-microvolt = <1800000>; > + qcom,micbias3-microvolt = <1800000>; > + qcom,micbias4-microvolt = <1800000>; > + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; > + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; > + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; > + qcom,rx-device = <&wcd_rx>; > + qcom,tx-device = <&wcd_tx>; > + > + reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>; > + > + vdd-buck-supply = <&vreg_l15b_1p8>; > + vdd-rxtx-supply = <&vreg_l15b_1p8>; > + vdd-io-supply = <&vreg_l15b_1p8>; > + vdd-mic-bias-supply = <&vreg_bob1>; > + > + #sound-dai-cells = <1>; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + hdmi-out { > + compatible = "hdmi-connector"; > + type = "a"; > + > + port { > + hdmi_connector_out: endpoint { > + remote-endpoint = <<9611_out>; > + }; > + }; > + }; > + > + vreg_bob_3v3: vreg-bob-3v3-regulator { Please rename all regulator nodes to start from the word regulator-. This allows grouping them in a logical way. > + compatible = "regulator-fixed"; > + > + regulator-name = "VREG_BOB_3P3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + vin-supply = <&vph_pwr>; > + }; > + > + lt9611_1v2: lt9611-vdd12-regulator { > + compatible = "regulator-fixed"; > + > + regulator-name = "LT9611_1V2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + > + vin-supply = <&vph_pwr>; > + gpio = <&tlmm 152 GPIO_ACTIVE_HIGH>; > + > + enable-active-high; > + }; > + > + lt9611_3v3: lt9611-3v3-regulator { > + compatible = "regulator-fixed"; > + > + regulator-name = "LT9611_3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + vin-supply = <&vreg_bob_3v3>; > + gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>; > + > + enable-active-high; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-0 = <&volume_up_n>; > + pinctrl-names = "default"; > + > + key-volume-up { > + label = "Volume Up"; > + linux,code = <KEY_VOLUMEUP>; > + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; > + debounce-interval = <15>; > + linux,can-disable; > + wakeup-source; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led-0 { > + function = LED_FUNCTION_BLUETOOTH; > + color = <LED_COLOR_ID_BLUE>; > + gpios = <&tlmm 159 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "bluetooth-power"; > + default-state = "off"; > + }; > + > + led-1 { > + function = LED_FUNCTION_INDICATOR; > + color = <LED_COLOR_ID_GREEN>; > + gpios = <&tlmm 160 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + panic-indicator; > + }; > + > + led-2 { > + function = LED_FUNCTION_WLAN; > + color = <LED_COLOR_ID_ORANGE>; > + gpios = <&tlmm 162 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "phy0tx"; > + default-state = "off"; > + }; > + }; > + > + pmic-glink { > + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink"; > + #address-cells = <1>; > + #size-cells = <0>; > + orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; > + > + connector@0 { > + compatible = "usb-c-connector"; > + reg = <0>; > + power-role = "dual"; > + data-role = "dual"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + pmic_glink_hs_in: endpoint { > + remote-endpoint = <&usb_1_dwc3_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + pmic_glink_ss_in: endpoint { > + remote-endpoint = <&usb_dp_qmpphy_out>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + pmic_glink_sbu: endpoint { > + remote-endpoint = <&fsa4480_sbu_mux>; > + }; > + }; > + }; > + }; > + }; > + > + sound { > + compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard"; > + model = "SM8550-HDK"; > + audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT", > + "SpkrRight IN", "WSA_SPK2 OUT", > + "IN1_HPHL", "HPHL_OUT", > + "IN2_HPHR", "HPHR_OUT", > + "AMIC1", "MIC BIAS1", > + "AMIC2", "MIC BIAS2", > + "AMIC5", "MIC BIAS4", > + "TX SWR_ADC0", "ADC1_OUTPUT", > + "TX SWR_ADC1", "ADC2_OUTPUT", > + "TX SWR_ADC3", "ADC4_OUTPUT"; > + > + Single empty line, please. > + wcd-playback-dai-link { > + link-name = "WCD Playback"; > + > + cpu { > + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; > + }; > + > + codec { > + sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; > + }; > + > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + > + wcd-capture-dai-link { > + link-name = "WCD Capture"; > + > + cpu { > + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; > + }; > + > + codec { > + sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>; > + }; > + > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + > + wsa-dai-link { > + link-name = "WSA Playback"; > + > + cpu { > + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; > + }; > + > + codec { > + sound-dai = <&north_spkr>, <&south_spkr>, <&swr0 0>, <&lpass_wsamacro 0>; > + }; > + > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + > + va-dai-link { > + link-name = "VA Capture"; > + > + cpu { > + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; > + }; > + > + codec { > + sound-dai = <&lpass_vamacro 0>; > + }; > + > + platform { > + sound-dai = <&q6apm>; > + }; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + regulator-always-on; > + regulator-boot-on; > + }; > +}; > + > +&apps_rsc { > + regulators-0 { > + compatible = "qcom,pm8550-rpmh-regulators"; > + > + vdd-bob1-supply = <&vph_pwr>; > + vdd-bob2-supply = <&vph_pwr>; > + vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>; > + vdd-l2-l13-l14-supply = <&vreg_bob1>; > + vdd-l3-supply = <&vreg_s4g_1p25>; > + vdd-l5-l16-supply = <&vreg_bob1>; > + vdd-l6-l7-supply = <&vreg_bob1>; > + vdd-l8-l9-supply = <&vreg_bob1>; > + vdd-l11-supply = <&vreg_s4g_1p25>; > + vdd-l12-supply = <&vreg_s6g_1p86>; > + vdd-l15-supply = <&vreg_s6g_1p86>; > + vdd-l17-supply = <&vreg_bob2>; > + > + qcom,pmic-id = "b"; > + > + vreg_bob1: bob1 { > + regulator-name = "vreg_bob1"; > + regulator-min-microvolt = <3296000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_bob2: bob2 { > + regulator-name = "vreg_bob2"; > + regulator-min-microvolt = <2720000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1b_1p8: ldo1 { > + regulator-name = "vreg_l1b_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2b_3p0: ldo2 { > + regulator-name = "vreg_l2b_3p0"; > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l5b_3p1: ldo5 { > + regulator-name = "vreg_l5b_3p1"; > + regulator-min-microvolt = <3104000>; > + regulator-max-microvolt = <3104000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6b_1p8: ldo6 { > + regulator-name = "vreg_l6b_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7b_1p8: ldo7 { > + regulator-name = "vreg_l7b_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l8b_1p8: ldo8 { > + regulator-name = "vreg_l8b_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9b_2p9: ldo9 { > + regulator-name = "vreg_l9b_2p9"; > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11b_1p2: ldo11 { > + regulator-name = "vreg_l11b_1p2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1504000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12b_1p8: ldo12 { > + regulator-name = "vreg_l12b_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l13b_3p0: ldo13 { > + regulator-name = "vreg_l13b_3p0"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l14b_3p2: ldo14 { > + regulator-name = "vreg_l14b_3p2"; > + regulator-min-microvolt = <3200000>; > + regulator-max-microvolt = <3200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l15b_1p8: ldo15 { > + regulator-name = "vreg_l15b_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l16b_2p8: ldo16 { > + regulator-name = "vreg_l16b_2p8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l17b_2p5: ldo17 { > + regulator-name = "vreg_l17b_2p5"; > + regulator-min-microvolt = <2504000>; > + regulator-max-microvolt = <2504000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-1 { > + compatible = "qcom,pm8550vs-rpmh-regulators"; > + > + vdd-l1-supply = <&vreg_s4g_1p25>; > + vdd-l2-supply = <&vreg_s4e_0p95>; > + vdd-l3-supply = <&vreg_s4e_0p95>; > + > + qcom,pmic-id = "c"; > + > + vreg_l3c_0p9: ldo3 { > + regulator-name = "vreg_l3c_0p9"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-2 { > + compatible = "qcom,pm8550vs-rpmh-regulators"; > + > + vdd-l1-supply = <&vreg_s4e_0p95>; > + vdd-l2-supply = <&vreg_s4e_0p95>; > + vdd-l3-supply = <&vreg_s4e_0p95>; > + > + qcom,pmic-id = "d"; > + > + vreg_l1d_0p88: ldo1 { > + regulator-name = "vreg_l1d_0p88"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <920000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* ldo2 supplies SM8550 VDD_LPI_MX */ > + }; > + > + regulators-3 { > + compatible = "qcom,pm8550vs-rpmh-regulators"; > + > + vdd-l1-supply = <&vreg_s4e_0p95>; > + vdd-l2-supply = <&vreg_s4e_0p95>; > + vdd-l3-supply = <&vreg_s4g_1p25>; > + vdd-s4-supply = <&vph_pwr>; > + vdd-s5-supply = <&vph_pwr>; > + > + qcom,pmic-id = "e"; > + > + vreg_s4e_0p95: smps4 { > + regulator-name = "vreg_s4e_0p95"; > + regulator-min-microvolt = <904000>; > + regulator-max-microvolt = <984000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s5e_1p08: smps5 { > + regulator-name = "vreg_s5e_1p08"; > + regulator-min-microvolt = <1080000>; > + regulator-max-microvolt = <1120000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1e_0p88: ldo1 { > + regulator-name = "vreg_l1e_0p88"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <880000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2e_0p9: ldo2 { > + regulator-name = "vreg_l2e_0p9"; > + regulator-min-microvolt = <904000>; > + regulator-max-microvolt = <970000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3e_1p2: ldo3 { > + regulator-name = "vreg_l3e_1p2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-4 { > + compatible = "qcom,pm8550ve-rpmh-regulators"; > + > + vdd-l1-supply = <&vreg_s4e_0p95>; > + vdd-l2-supply = <&vreg_s4e_0p95>; > + vdd-l3-supply = <&vreg_s4e_0p95>; > + vdd-s4-supply = <&vph_pwr>; > + > + qcom,pmic-id = "f"; > + > + vreg_s4f_0p5: smps4 { > + regulator-name = "vreg_s4f_0p5"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <700000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1f_0p9: ldo1 { > + regulator-name = "vreg_l1f_0p9"; > + regulator-min-microvolt = <912000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2f_0p88: ldo2 { > + regulator-name = "vreg_l2f_0p88"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3f_0p88: ldo3 { > + regulator-name = "vreg_l3f_0p88"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-5 { > + compatible = "qcom,pm8550vs-rpmh-regulators"; > + > + vdd-l1-supply = <&vreg_s4g_1p25>; > + vdd-l2-supply = <&vreg_s4g_1p25>; > + vdd-l3-supply = <&vreg_s4g_1p25>; > + vdd-s1-supply = <&vph_pwr>; > + vdd-s2-supply = <&vph_pwr>; > + vdd-s3-supply = <&vph_pwr>; > + vdd-s4-supply = <&vph_pwr>; > + vdd-s5-supply = <&vph_pwr>; > + vdd-s6-supply = <&vph_pwr>; > + > + qcom,pmic-id = "g"; > + > + vreg_s1g_1p25: smps1 { > + regulator-name = "vreg_s1g_1p25"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s2g_0p85: smps2 { > + regulator-name = "vreg_s2g_0p85"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s3g_0p8: smps3 { > + regulator-name = "vreg_s3g_0p8"; > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1004000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s4g_1p25: smps4 { > + regulator-name = "vreg_s4g_1p25"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1352000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s5g_0p85: smps5 { > + regulator-name = "vreg_s5g_0p85"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1004000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s6g_1p86: smps6 { > + regulator-name = "vreg_s6g_1p86"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1g_1p2: ldo1 { > + regulator-name = "vreg_l1g_1p2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3g_1p2: ldo3 { > + regulator-name = "vreg_l3g_1p2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-6 { > + compatible = "qcom,pm8010-rpmh-regulators"; > + > + vdd-l1-l2-supply = <&vreg_s4g_1p25>; > + vdd-l3-l4-supply = <&vreg_bob2>; > + vdd-l5-supply = <&vreg_s6g_1p86>; > + vdd-l6-supply = <&vreg_s6g_1p86>; > + vdd-l7-supply = <&vreg_bob1>; > + > + qcom,pmic-id = "m"; > + > + vreg_l1m_1p056: ldo1 { > + regulator-name = "vreg_l1m_1p056"; > + regulator-min-microvolt = <1056000>; > + regulator-max-microvolt = <1056000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2m_1p056: ldo2 { > + regulator-name = "vreg_l2m_1p056"; > + regulator-min-microvolt = <1056000>; > + regulator-max-microvolt = <1056000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3m_2p8: ldo3 { > + regulator-name = "vreg_l3m_2p8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4m_2p8: ldo4 { > + regulator-name = "vreg_l4m_2p8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l5m_1p8: ldo5 { > + regulator-name = "vreg_l5m_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6m_1p8: ldo6 { > + regulator-name = "vreg_l6m_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7m_2p9: ldo7 { > + regulator-name = "vreg_l7m_2p9"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2904000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-7 { > + compatible = "qcom,pm8010-rpmh-regulators"; > + > + vdd-l1-l2-supply = <&vreg_s4g_1p25>; > + vdd-l3-l4-supply = <&vreg_bob2>; > + vdd-l5-supply = <&vreg_s6g_1p86>; > + vdd-l6-supply = <&vreg_bob1>; > + vdd-l7-supply = <&vreg_bob1>; > + > + qcom,pmic-id = "n"; > + > + vreg_l1n_1p1: ldo1 { > + regulator-name = "vreg_l1n_1p1"; > + regulator-min-microvolt = <1104000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2n_1p1: ldo2 { > + regulator-name = "vreg_l2n_1p1"; > + regulator-min-microvolt = <1104000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3n_2p8: ldo3 { > + regulator-name = "vreg_l3n_2p8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <3000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4n_2p8: ldo4 { > + regulator-name = "vreg_l4n_2p8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <3300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l5n_1p8: ldo5 { > + regulator-name = "vreg_l5n_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6n_3p3: ldo6 { > + regulator-name = "vreg_l6n_3p3"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7n_2p96: ldo7 { > + regulator-name = "vreg_l7n_2p96"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > +}; > + > +&i2c_master_hub_0 { > + status = "okay"; > +}; > + > +&i2c0 { > + clock-frequency = <400000>; > + status = "okay"; > + > + lt9611_codec: hdmi-bridge@2b { > + compatible = "lontium,lt9611uxc"; > + reg = <0x2b>; > + > + interrupts-extended = <&tlmm 8 IRQ_TYPE_EDGE_FALLING>; > + > + reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>; > + > + vdd-supply = <<9611_1v2>; > + vcc-supply = <<9611_3v3>; > + > + pinctrl-0 = <<9611_irq_pin>, <<9611_rst_pin>; > + pinctrl-names = "default"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + lt9611_a: endpoint { > + remote-endpoint = <&mdss_dsi0_out>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + lt9611_out: endpoint { > + remote-endpoint = <&hdmi_connector_out>; > + }; > + }; > + }; > + }; > +}; > + > +&i2c_hub_2 { > + status = "okay"; > + > + typec-mux@42 { > + compatible = "fcs,fsa4480"; > + reg = <0x42>; > + > + vcc-supply = <&vreg_bob1>; > + > + mode-switch; > + orientation-switch; > + > + port { > + fsa4480_sbu_mux: endpoint { > + remote-endpoint = <&pmic_glink_sbu>; > + }; > + }; > + }; > +}; i2c_master_hub i2c0 i2c_hub_2 The order doesn't seem to be correct. > + > +&ipa { > + qcom,gsi-loader = "self"; > + memory-region = <&ipa_fw_mem>; > + firmware-name = "qcom/sm8550/ipa_fws.mbn"; > + status = "okay"; > +}; > + > +&gpu { > + status = "okay"; > + > + zap-shader { > + firmware-name = "qcom/sm8550/a740_zap.mbn"; > + }; > +}; This comes before i2c > + > +&lpass_tlmm { > + spkr_1_sd_n_active: spkr-1-sd-n-active-state { > + pins = "gpio17"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + output-low; > + }; > + > + spkr_2_sd_n_active: spkr-2-sd-n-active-state { > + pins = "gpio18"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + output-low; > + }; > +}; > + > +&mdss { > + status = "okay"; > +}; > + > +&mdss_dsi0 { > + vdda-supply = <&vreg_l3e_1p2>; > + status = "okay"; > +}; > + > +&mdss_dsi0_out { > + remote-endpoint = <<9611_a>; > + data-lanes = <0 1 2 3>; > +}; > + > +&mdss_dsi0_phy { > + vdds-supply = <&vreg_l1e_0p88>; > + status = "okay"; > +}; > + > +&mdss_dp0 { > + status = "okay"; > +}; > + > +&mdss_dp0_out { > + remote-endpoint = <&usb_dp_qmpphy_dp_in>; > + data-lanes = <0 1>; > +}; > + > +&pcie0 { > + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; > + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; > + > + pinctrl-0 = <&pcie0_default_state>; > + pinctrl-names = "default"; > + > + status = "okay"; > +}; > + > +&pcie0_phy { > + vdda-phy-supply = <&vreg_l1e_0p88>; > + vdda-pll-supply = <&vreg_l3e_1p2>; > + > + status = "okay"; > +}; > + > +&pcie1 { > + wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; > + perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>; > + > + pinctrl-0 = <&pcie1_default_state>; > + pinctrl-names = "default"; > + > + status = "okay"; > +}; > + > +&pcie1_phy { > + vdda-phy-supply = <&vreg_l3c_0p9>; > + vdda-pll-supply = <&vreg_l3e_1p2>; > + vdda-qref-supply = <&vreg_l1e_0p88>; > + > + status = "okay"; > +}; > + > +&pm8550_gpios { > + sdc2_card_det_n: sdc2-card-det-state { > + pins = "gpio12"; > + function = "normal"; > + input-enable; > + output-disable; > + bias-pull-up; > + power-source = <1>; /* 1.8 V */ > + }; > + > + volume_up_n: volume-up-n-state { > + pins = "gpio6"; > + function = "normal"; > + power-source = <1>; > + bias-pull-up; > + input-enable; > + }; > +}; > + > +/* The RGB signals are routed to 3 separate LEDs on the HDK8550 */ > +&pm8550_pwm { > + #address-cells = <1>; > + #size-cells = <0>; > + > + status = "okay"; > + > + led@1 { > + reg = <1>; > + function = LED_FUNCTION_STATUS; > + color = <LED_COLOR_ID_RED>; > + default-state = "off"; > + }; > + > + led@2 { > + reg = <2>; > + function = LED_FUNCTION_STATUS; > + color = <LED_COLOR_ID_GREEN>; > + default-state = "off"; > + }; > + > + led@3 { > + reg = <3>; > + function = LED_FUNCTION_STATUS; > + color = <LED_COLOR_ID_BLUE>; > + default-state = "off"; > + }; > +}; > + > +&pm8550b_eusb2_repeater { > + vdd18-supply = <&vreg_l15b_1p8>; > + vdd3-supply = <&vreg_l5b_3p1>; > +}; > + > +&pon_pwrkey { > + status = "okay"; > +}; > + > +&pon_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + > + status = "okay"; > +}; > + > +&pcie_1_phy_aux_clk { > + clock-frequency = <1000>; > +}; Next to other PCIe nodes? > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&qupv3_id_1 { > + status = "okay"; > +}; BTW, don't we need to enable gpi_dma nodes for qup / i2c to work? > + > +&remoteproc_adsp { > + firmware-name = "qcom/sm8550/adsp.mbn", > + "qcom/sm8550/adsp_dtb.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_cdsp { > + firmware-name = "qcom/sm8550/cdsp.mbn", > + "qcom/sm8550/cdsp_dtb.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_mpss { > + firmware-name = "qcom/sm8550/modem.mbn", > + "qcom/sm8550/modem_dtb.mbn"; > + status = "okay"; > +}; > + > +&sdhc_2 { > + cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>; > + pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>; > + pinctrl-names = "default", "sleep"; > + > + vmmc-supply = <&vreg_l9b_2p9>; > + vqmmc-supply = <&vreg_l8b_1p8>; > + > + bus-width = <4>; > + no-sdio; > + no-mmc; > + > + status = "okay"; > +}; > + > +&sleep_clk { > + clock-frequency = <32000>; > +}; > + > +&swr0 { > + status = "okay"; > + > + /* WSA8845, Speaker North */ > + north_spkr: speaker@0,0 { > + compatible = "sdw20217020400"; > + reg = <0 0>; > + > + pinctrl-0 = <&spkr_1_sd_n_active>; > + pinctrl-names = "default"; > + > + powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>; > + > + vdd-1p8-supply = <&vreg_l15b_1p8>; > + vdd-io-supply = <&vreg_l15b_1p8>; > + > + #sound-dai-cells = <0>; > + sound-name-prefix = "SpkrLeft"; > + }; > + > + /* WSA8845, Speaker South */ > + south_spkr: speaker@0,1 { > + compatible = "sdw20217020400"; > + reg = <0 1>; > + > + pinctrl-0 = <&spkr_2_sd_n_active>; > + pinctrl-names = "default"; > + > + powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>; > + > + vdd-1p8-supply = <&vreg_l15b_1p8>; > + vdd-io-supply = <&vreg_l15b_1p8>; > + > + #sound-dai-cells = <0>; > + sound-name-prefix = "SpkrRight"; > + }; > +}; > + > +&swr1 { > + status = "okay"; > + > + /* WCD9385 RX */ > + wcd_rx: codec@0,4 { > + compatible = "sdw20217010d00"; > + reg = <0 4>; > + > + qcom,rx-port-mapping = <1 2 3 4 5>; > + }; > +}; > + > +&swr2 { > + status = "okay"; > + > + /* WCD9385 TX */ > + wcd_tx: codec@0,3 { > + compatible = "sdw20217010d00"; > + reg = <0 3>; > + > + qcom,tx-port-mapping = <1 1 2 3>; > + }; > +}; > + > +&tlmm { > + /* Reserved I/Os for NFC */ > + gpio-reserved-ranges = <32 8>; > + > + bt_default: bt-default-state { > + bt-en-pins { > + pins = "gpio81"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + sw-ctrl-pins { > + pins = "gpio82"; > + function = "gpio"; > + bias-pull-down; > + }; > + }; > + > + lt9611_irq_pin: lt9611-irq-state { > + pins = "gpio8"; > + function = "gpio"; > + bias-disable; > + }; > + > + lt9611_rst_pin: lt9611-rst-state { > + pins = "gpio7"; > + function = "gpio"; > + output-high; > + }; > + > + wcd_default: wcd-reset-n-active-state { > + pins = "gpio108"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + output-low; > + }; > +}; > + > +&uart7 { > + status = "okay"; > +}; > + > +&uart14 { > + status = "okay"; > + > + bluetooth { > + compatible = "qcom,wcn7850-bt"; > + > + vddio-supply = <&vreg_l15b_1p8>; > + vddaon-supply = <&vreg_s4e_0p95>; > + vdddig-supply = <&vreg_s4e_0p95>; > + vddrfa0p8-supply = <&vreg_s4e_0p95>; > + vddrfa1p2-supply = <&vreg_s4g_1p25>; > + vddrfa1p9-supply = <&vreg_s6g_1p86>; > + > + max-speed = <3200000>; > + > + enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>; > + swctrl-gpios = <&tlmm 82 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&bt_default>; > + pinctrl-names = "default"; > + }; > +}; > + > +&ufs_mem_hc { > + reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>; > + > + vcc-supply = <&vreg_l17b_2p5>; > + vcc-max-microamp = <1300000>; > + vccq-supply = <&vreg_l1g_1p2>; > + vccq-max-microamp = <1200000>; > + vdd-hba-supply = <&vreg_l3g_1p2>; > + > + status = "okay"; > +}; > + > +&ufs_mem_phy { > + vdda-phy-supply = <&vreg_l1d_0p88>; > + vdda-pll-supply = <&vreg_l3e_1p2>; > + > + status = "okay"; > +}; > + > +&usb_1 { > + status = "okay"; > +}; > + > +&usb_1_dwc3 { > + dr_mode = "otg"; otg is a default > + usb-role-switch; > +}; > + > +&usb_1_dwc3_hs { > + remote-endpoint = <&pmic_glink_hs_in>; > +}; > + > +&usb_1_dwc3_ss { > + remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>; > +}; > + > +&usb_1_hsphy { > + vdd-supply = <&vreg_l1e_0p88>; > + vdda12-supply = <&vreg_l3e_1p2>; > + > + phys = <&pm8550b_eusb2_repeater>; > + > + status = "okay"; > +}; > + > +&usb_dp_qmpphy { > + vdda-phy-supply = <&vreg_l3e_1p2>; > + vdda-pll-supply = <&vreg_l3f_0p88>; > + > + orientation-switch; Shouldn't this property be moved to the base dtsi? > + > + status = "okay"; > +}; > + > +&usb_dp_qmpphy_dp_in { > + remote-endpoint = <&mdss_dp0_out>; > +}; > + > +&usb_dp_qmpphy_out { > + remote-endpoint = <&pmic_glink_ss_in>; > +}; > + > +&usb_dp_qmpphy_usb_ss_in { > + remote-endpoint = <&usb_1_dwc3_ss>; > +}; > + > +&xo_board { > + clock-frequency = <76800000>; > +}; > > -- > 2.34.1 > >
On 23/01/2024 10:10, Dmitry Baryshkov wrote: > On Tue, 23 Jan 2024 at 10:56, Neil Armstrong <neil.armstrong@linaro.org> wrote: >> >> The SM8550-HDK is an embedded development platforms for the >> Snapdragon 8 Gen 2 SoC aka SM8550, with the following features: >> - Qualcomm SM8550 SoC >> - 16GiB On-board LPDDR5 >> - On-board WiFi 7 + Bluetooth 5.3/BLE >> - On-board UFS4.0 >> - M.2 Key B+M Gen3x2 PCIe Slot >> - HDMI Output >> - USB-C Connector with DP Almode & Audio Accessory mode >> - Micro-SDCard Slot >> - Audio Jack with Playback and Microphone >> - 2 On-board Analog microphones >> - 2 On-board Speakers >> - 96Boards Compatible Low-Speed and High-Speed connectors [1] >> - For Camera, Sensors and external Display cards >> - Compatible with the Linaro Debug board [2] >> - SIM Slot for Modem >> - Debug connectors >> - 6x On-Board LEDs >> >> Product Page: [3] >> >> [1] https://www.96boards.org/specifications/ >> [2] https://git.codelinaro.org/linaro/qcomlt/debugboard >> [3] https://www.lantronix.com/products/snapdragon-8-gen-2-mobile-hardware-development-kit/ >> >> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> >> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> >> --- >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> arch/arm64/boot/dts/qcom/sm8550-hdk.dts | 1290 +++++++++++++++++++++++++++++++ >> 2 files changed, 1291 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile >> index 39889d5f8e12..42e50f2b2ec3 100644 >> --- a/arch/arm64/boot/dts/qcom/Makefile >> +++ b/arch/arm64/boot/dts/qcom/Makefile >> @@ -233,6 +233,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-hdk.dtb >> dtb-$(CONFIG_ARCH_QCOM) += sm8450-qrd.dtb >> dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx223.dtb >> dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb >> +dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb >> dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb >> dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb >> dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb >> diff --git a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts >> new file mode 100644 >> index 000000000000..66bdd6c269ea >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts >> @@ -0,0 +1,1290 @@ >> +// SPDX-License-Identifier: BSD-3-Clause >> +/* >> + * Copyright (c) 2024 Linaro Limited >> + */ >> + >> +/dts-v1/; >> + >> +#include <dt-bindings/leds/common.h> >> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> >> +#include "sm8550.dtsi" >> +#include "pm8010.dtsi" >> +#include "pm8550.dtsi" >> +#include "pm8550b.dtsi" >> +#define PMK8550VE_SID 5 > > Maybe the define should be moved before all include files and > separated with the blank line? Why ? I prefer keeping it close the the include file consuming the define > >> +#include "pm8550ve.dtsi" >> +#include "pm8550vs.dtsi" >> +#include "pmk8550.dtsi" >> +#include "pmr735d_a.dtsi" >> + >> +/ { >> + model = "Qualcomm Technologies, Inc. SM8550 HDK"; >> + compatible = "qcom,sm8550-hdk", "qcom,sm8550"; >> + chassis-type = "embedded"; >> + >> + aliases { >> + serial0 = &uart7; >> + serial1 = &uart14; >> + }; >> + >> + wcd938x: audio-codec { >> + compatible = "qcom,wcd9385-codec"; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&wcd_default>; >> + >> + qcom,micbias1-microvolt = <1800000>; >> + qcom,micbias2-microvolt = <1800000>; >> + qcom,micbias3-microvolt = <1800000>; >> + qcom,micbias4-microvolt = <1800000>; >> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; >> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; >> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; >> + qcom,rx-device = <&wcd_rx>; >> + qcom,tx-device = <&wcd_tx>; >> + >> + reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>; >> + >> + vdd-buck-supply = <&vreg_l15b_1p8>; >> + vdd-rxtx-supply = <&vreg_l15b_1p8>; >> + vdd-io-supply = <&vreg_l15b_1p8>; >> + vdd-mic-bias-supply = <&vreg_bob1>; >> + >> + #sound-dai-cells = <1>; >> + }; >> + >> + chosen { >> + stdout-path = "serial0:115200n8"; >> + }; >> + >> + hdmi-out { >> + compatible = "hdmi-connector"; >> + type = "a"; >> + >> + port { >> + hdmi_connector_out: endpoint { >> + remote-endpoint = <<9611_out>; >> + }; >> + }; >> + }; >> + >> + vreg_bob_3v3: vreg-bob-3v3-regulator { > > Please rename all regulator nodes to start from the word regulator-. > This allows grouping them in a logical way. Ack > >> + compatible = "regulator-fixed"; >> + >> + regulator-name = "VREG_BOB_3P3"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + >> + vin-supply = <&vph_pwr>; >> + }; >> + >> + lt9611_1v2: lt9611-vdd12-regulator { >> + compatible = "regulator-fixed"; >> + >> + regulator-name = "LT9611_1V2"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + >> + vin-supply = <&vph_pwr>; >> + gpio = <&tlmm 152 GPIO_ACTIVE_HIGH>; >> + >> + enable-active-high; >> + }; >> + >> + lt9611_3v3: lt9611-3v3-regulator { >> + compatible = "regulator-fixed"; >> + >> + regulator-name = "LT9611_3V3"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + >> + vin-supply = <&vreg_bob_3v3>; >> + gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>; >> + >> + enable-active-high; >> + }; >> + >> + gpio-keys { >> + compatible = "gpio-keys"; >> + >> + pinctrl-0 = <&volume_up_n>; >> + pinctrl-names = "default"; >> + >> + key-volume-up { >> + label = "Volume Up"; >> + linux,code = <KEY_VOLUMEUP>; >> + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; >> + debounce-interval = <15>; >> + linux,can-disable; >> + wakeup-source; >> + }; >> + }; >> + >> + leds { >> + compatible = "gpio-leds"; >> + >> + led-0 { >> + function = LED_FUNCTION_BLUETOOTH; >> + color = <LED_COLOR_ID_BLUE>; >> + gpios = <&tlmm 159 GPIO_ACTIVE_HIGH>; >> + linux,default-trigger = "bluetooth-power"; >> + default-state = "off"; >> + }; >> + >> + led-1 { >> + function = LED_FUNCTION_INDICATOR; >> + color = <LED_COLOR_ID_GREEN>; >> + gpios = <&tlmm 160 GPIO_ACTIVE_HIGH>; >> + default-state = "off"; >> + panic-indicator; >> + }; >> + >> + led-2 { >> + function = LED_FUNCTION_WLAN; >> + color = <LED_COLOR_ID_ORANGE>; >> + gpios = <&tlmm 162 GPIO_ACTIVE_HIGH>; >> + linux,default-trigger = "phy0tx"; >> + default-state = "off"; >> + }; >> + }; >> + >> + pmic-glink { >> + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; >> + >> + connector@0 { >> + compatible = "usb-c-connector"; >> + reg = <0>; >> + power-role = "dual"; >> + data-role = "dual"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + pmic_glink_hs_in: endpoint { >> + remote-endpoint = <&usb_1_dwc3_hs>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + pmic_glink_ss_in: endpoint { >> + remote-endpoint = <&usb_dp_qmpphy_out>; >> + }; >> + }; >> + >> + port@2 { >> + reg = <2>; >> + >> + pmic_glink_sbu: endpoint { >> + remote-endpoint = <&fsa4480_sbu_mux>; >> + }; >> + }; >> + }; >> + }; >> + }; >> + >> + sound { >> + compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard"; >> + model = "SM8550-HDK"; >> + audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT", >> + "SpkrRight IN", "WSA_SPK2 OUT", >> + "IN1_HPHL", "HPHL_OUT", >> + "IN2_HPHR", "HPHR_OUT", >> + "AMIC1", "MIC BIAS1", >> + "AMIC2", "MIC BIAS2", >> + "AMIC5", "MIC BIAS4", >> + "TX SWR_ADC0", "ADC1_OUTPUT", >> + "TX SWR_ADC1", "ADC2_OUTPUT", >> + "TX SWR_ADC3", "ADC4_OUTPUT"; >> + >> + > > Single empty line, please. > >> + wcd-playback-dai-link { >> + link-name = "WCD Playback"; >> + >> + cpu { >> + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; >> + }; >> + >> + codec { >> + sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; >> + }; >> + >> + platform { >> + sound-dai = <&q6apm>; >> + }; >> + }; >> + >> + wcd-capture-dai-link { >> + link-name = "WCD Capture"; >> + >> + cpu { >> + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; >> + }; >> + >> + codec { >> + sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>; >> + }; >> + >> + platform { >> + sound-dai = <&q6apm>; >> + }; >> + }; >> + >> + wsa-dai-link { >> + link-name = "WSA Playback"; >> + >> + cpu { >> + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; >> + }; >> + >> + codec { >> + sound-dai = <&north_spkr>, <&south_spkr>, <&swr0 0>, <&lpass_wsamacro 0>; >> + }; >> + >> + platform { >> + sound-dai = <&q6apm>; >> + }; >> + }; >> + >> + va-dai-link { >> + link-name = "VA Capture"; >> + >> + cpu { >> + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; >> + }; >> + >> + codec { >> + sound-dai = <&lpass_vamacro 0>; >> + }; >> + >> + platform { >> + sound-dai = <&q6apm>; >> + }; >> + }; >> + }; >> + >> + vph_pwr: vph-pwr-regulator { >> + compatible = "regulator-fixed"; >> + >> + regulator-name = "vph_pwr"; >> + regulator-min-microvolt = <3700000>; >> + regulator-max-microvolt = <3700000>; >> + regulator-always-on; >> + regulator-boot-on; >> + }; >> +}; >> + >> +&apps_rsc { >> + regulators-0 { >> + compatible = "qcom,pm8550-rpmh-regulators"; >> + >> + vdd-bob1-supply = <&vph_pwr>; >> + vdd-bob2-supply = <&vph_pwr>; >> + vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>; >> + vdd-l2-l13-l14-supply = <&vreg_bob1>; >> + vdd-l3-supply = <&vreg_s4g_1p25>; >> + vdd-l5-l16-supply = <&vreg_bob1>; >> + vdd-l6-l7-supply = <&vreg_bob1>; >> + vdd-l8-l9-supply = <&vreg_bob1>; >> + vdd-l11-supply = <&vreg_s4g_1p25>; >> + vdd-l12-supply = <&vreg_s6g_1p86>; >> + vdd-l15-supply = <&vreg_s6g_1p86>; >> + vdd-l17-supply = <&vreg_bob2>; >> + >> + qcom,pmic-id = "b"; >> + >> + vreg_bob1: bob1 { >> + regulator-name = "vreg_bob1"; >> + regulator-min-microvolt = <3296000>; >> + regulator-max-microvolt = <3960000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_bob2: bob2 { >> + regulator-name = "vreg_bob2"; >> + regulator-min-microvolt = <2720000>; >> + regulator-max-microvolt = <3960000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l1b_1p8: ldo1 { >> + regulator-name = "vreg_l1b_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l2b_3p0: ldo2 { >> + regulator-name = "vreg_l2b_3p0"; >> + regulator-min-microvolt = <3008000>; >> + regulator-max-microvolt = <3008000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l5b_3p1: ldo5 { >> + regulator-name = "vreg_l5b_3p1"; >> + regulator-min-microvolt = <3104000>; >> + regulator-max-microvolt = <3104000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l6b_1p8: ldo6 { >> + regulator-name = "vreg_l6b_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3008000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l7b_1p8: ldo7 { >> + regulator-name = "vreg_l7b_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3008000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l8b_1p8: ldo8 { >> + regulator-name = "vreg_l8b_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3008000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l9b_2p9: ldo9 { >> + regulator-name = "vreg_l9b_2p9"; >> + regulator-min-microvolt = <2960000>; >> + regulator-max-microvolt = <3008000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l11b_1p2: ldo11 { >> + regulator-name = "vreg_l11b_1p2"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1504000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l12b_1p8: ldo12 { >> + regulator-name = "vreg_l12b_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l13b_3p0: ldo13 { >> + regulator-name = "vreg_l13b_3p0"; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l14b_3p2: ldo14 { >> + regulator-name = "vreg_l14b_3p2"; >> + regulator-min-microvolt = <3200000>; >> + regulator-max-microvolt = <3200000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l15b_1p8: ldo15 { >> + regulator-name = "vreg_l15b_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l16b_2p8: ldo16 { >> + regulator-name = "vreg_l16b_2p8"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l17b_2p5: ldo17 { >> + regulator-name = "vreg_l17b_2p5"; >> + regulator-min-microvolt = <2504000>; >> + regulator-max-microvolt = <2504000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> + >> + regulators-1 { >> + compatible = "qcom,pm8550vs-rpmh-regulators"; >> + >> + vdd-l1-supply = <&vreg_s4g_1p25>; >> + vdd-l2-supply = <&vreg_s4e_0p95>; >> + vdd-l3-supply = <&vreg_s4e_0p95>; >> + >> + qcom,pmic-id = "c"; >> + >> + vreg_l3c_0p9: ldo3 { >> + regulator-name = "vreg_l3c_0p9"; >> + regulator-min-microvolt = <880000>; >> + regulator-max-microvolt = <912000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> + >> + regulators-2 { >> + compatible = "qcom,pm8550vs-rpmh-regulators"; >> + >> + vdd-l1-supply = <&vreg_s4e_0p95>; >> + vdd-l2-supply = <&vreg_s4e_0p95>; >> + vdd-l3-supply = <&vreg_s4e_0p95>; >> + >> + qcom,pmic-id = "d"; >> + >> + vreg_l1d_0p88: ldo1 { >> + regulator-name = "vreg_l1d_0p88"; >> + regulator-min-microvolt = <880000>; >> + regulator-max-microvolt = <920000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + /* ldo2 supplies SM8550 VDD_LPI_MX */ >> + }; >> + >> + regulators-3 { >> + compatible = "qcom,pm8550vs-rpmh-regulators"; >> + >> + vdd-l1-supply = <&vreg_s4e_0p95>; >> + vdd-l2-supply = <&vreg_s4e_0p95>; >> + vdd-l3-supply = <&vreg_s4g_1p25>; >> + vdd-s4-supply = <&vph_pwr>; >> + vdd-s5-supply = <&vph_pwr>; >> + >> + qcom,pmic-id = "e"; >> + >> + vreg_s4e_0p95: smps4 { >> + regulator-name = "vreg_s4e_0p95"; >> + regulator-min-microvolt = <904000>; >> + regulator-max-microvolt = <984000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_s5e_1p08: smps5 { >> + regulator-name = "vreg_s5e_1p08"; >> + regulator-min-microvolt = <1080000>; >> + regulator-max-microvolt = <1120000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l1e_0p88: ldo1 { >> + regulator-name = "vreg_l1e_0p88"; >> + regulator-min-microvolt = <880000>; >> + regulator-max-microvolt = <880000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l2e_0p9: ldo2 { >> + regulator-name = "vreg_l2e_0p9"; >> + regulator-min-microvolt = <904000>; >> + regulator-max-microvolt = <970000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l3e_1p2: ldo3 { >> + regulator-name = "vreg_l3e_1p2"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> + >> + regulators-4 { >> + compatible = "qcom,pm8550ve-rpmh-regulators"; >> + >> + vdd-l1-supply = <&vreg_s4e_0p95>; >> + vdd-l2-supply = <&vreg_s4e_0p95>; >> + vdd-l3-supply = <&vreg_s4e_0p95>; >> + vdd-s4-supply = <&vph_pwr>; >> + >> + qcom,pmic-id = "f"; >> + >> + vreg_s4f_0p5: smps4 { >> + regulator-name = "vreg_s4f_0p5"; >> + regulator-min-microvolt = <500000>; >> + regulator-max-microvolt = <700000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l1f_0p9: ldo1 { >> + regulator-name = "vreg_l1f_0p9"; >> + regulator-min-microvolt = <912000>; >> + regulator-max-microvolt = <912000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l2f_0p88: ldo2 { >> + regulator-name = "vreg_l2f_0p88"; >> + regulator-min-microvolt = <880000>; >> + regulator-max-microvolt = <912000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l3f_0p88: ldo3 { >> + regulator-name = "vreg_l3f_0p88"; >> + regulator-min-microvolt = <880000>; >> + regulator-max-microvolt = <912000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> + >> + regulators-5 { >> + compatible = "qcom,pm8550vs-rpmh-regulators"; >> + >> + vdd-l1-supply = <&vreg_s4g_1p25>; >> + vdd-l2-supply = <&vreg_s4g_1p25>; >> + vdd-l3-supply = <&vreg_s4g_1p25>; >> + vdd-s1-supply = <&vph_pwr>; >> + vdd-s2-supply = <&vph_pwr>; >> + vdd-s3-supply = <&vph_pwr>; >> + vdd-s4-supply = <&vph_pwr>; >> + vdd-s5-supply = <&vph_pwr>; >> + vdd-s6-supply = <&vph_pwr>; >> + >> + qcom,pmic-id = "g"; >> + >> + vreg_s1g_1p25: smps1 { >> + regulator-name = "vreg_s1g_1p25"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_s2g_0p85: smps2 { >> + regulator-name = "vreg_s2g_0p85"; >> + regulator-min-microvolt = <800000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_s3g_0p8: smps3 { >> + regulator-name = "vreg_s3g_0p8"; >> + regulator-min-microvolt = <300000>; >> + regulator-max-microvolt = <1004000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_s4g_1p25: smps4 { >> + regulator-name = "vreg_s4g_1p25"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1352000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_s5g_0p85: smps5 { >> + regulator-name = "vreg_s5g_0p85"; >> + regulator-min-microvolt = <500000>; >> + regulator-max-microvolt = <1004000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_s6g_1p86: smps6 { >> + regulator-name = "vreg_s6g_1p86"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <2000000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l1g_1p2: ldo1 { >> + regulator-name = "vreg_l1g_1p2"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l3g_1p2: ldo3 { >> + regulator-name = "vreg_l3g_1p2"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> + >> + regulators-6 { >> + compatible = "qcom,pm8010-rpmh-regulators"; >> + >> + vdd-l1-l2-supply = <&vreg_s4g_1p25>; >> + vdd-l3-l4-supply = <&vreg_bob2>; >> + vdd-l5-supply = <&vreg_s6g_1p86>; >> + vdd-l6-supply = <&vreg_s6g_1p86>; >> + vdd-l7-supply = <&vreg_bob1>; >> + >> + qcom,pmic-id = "m"; >> + >> + vreg_l1m_1p056: ldo1 { >> + regulator-name = "vreg_l1m_1p056"; >> + regulator-min-microvolt = <1056000>; >> + regulator-max-microvolt = <1056000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l2m_1p056: ldo2 { >> + regulator-name = "vreg_l2m_1p056"; >> + regulator-min-microvolt = <1056000>; >> + regulator-max-microvolt = <1056000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l3m_2p8: ldo3 { >> + regulator-name = "vreg_l3m_2p8"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l4m_2p8: ldo4 { >> + regulator-name = "vreg_l4m_2p8"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l5m_1p8: ldo5 { >> + regulator-name = "vreg_l5m_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l6m_1p8: ldo6 { >> + regulator-name = "vreg_l6m_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l7m_2p9: ldo7 { >> + regulator-name = "vreg_l7m_2p9"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2904000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> + >> + regulators-7 { >> + compatible = "qcom,pm8010-rpmh-regulators"; >> + >> + vdd-l1-l2-supply = <&vreg_s4g_1p25>; >> + vdd-l3-l4-supply = <&vreg_bob2>; >> + vdd-l5-supply = <&vreg_s6g_1p86>; >> + vdd-l6-supply = <&vreg_bob1>; >> + vdd-l7-supply = <&vreg_bob1>; >> + >> + qcom,pmic-id = "n"; >> + >> + vreg_l1n_1p1: ldo1 { >> + regulator-name = "vreg_l1n_1p1"; >> + regulator-min-microvolt = <1104000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l2n_1p1: ldo2 { >> + regulator-name = "vreg_l2n_1p1"; >> + regulator-min-microvolt = <1104000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + regulator-allow-set-load; >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM >> + RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l3n_2p8: ldo3 { >> + regulator-name = "vreg_l3n_2p8"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l4n_2p8: ldo4 { >> + regulator-name = "vreg_l4n_2p8"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l5n_1p8: ldo5 { >> + regulator-name = "vreg_l5n_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l6n_3p3: ldo6 { >> + regulator-name = "vreg_l6n_3p3"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <3304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l7n_2p96: ldo7 { >> + regulator-name = "vreg_l7n_2p96"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2960000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> +}; >> + >> +&i2c_master_hub_0 { >> + status = "okay"; >> +}; >> + >> +&i2c0 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + lt9611_codec: hdmi-bridge@2b { >> + compatible = "lontium,lt9611uxc"; >> + reg = <0x2b>; >> + >> + interrupts-extended = <&tlmm 8 IRQ_TYPE_EDGE_FALLING>; >> + >> + reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>; >> + >> + vdd-supply = <<9611_1v2>; >> + vcc-supply = <<9611_3v3>; >> + >> + pinctrl-0 = <<9611_irq_pin>, <<9611_rst_pin>; >> + pinctrl-names = "default"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + lt9611_a: endpoint { >> + remote-endpoint = <&mdss_dsi0_out>; >> + }; >> + }; >> + >> + port@2 { >> + reg = <2>; >> + >> + lt9611_out: endpoint { >> + remote-endpoint = <&hdmi_connector_out>; >> + }; >> + }; >> + }; >> + }; >> +}; >> + >> +&i2c_hub_2 { >> + status = "okay"; >> + >> + typec-mux@42 { >> + compatible = "fcs,fsa4480"; >> + reg = <0x42>; >> + >> + vcc-supply = <&vreg_bob1>; >> + >> + mode-switch; >> + orientation-switch; >> + >> + port { >> + fsa4480_sbu_mux: endpoint { >> + remote-endpoint = <&pmic_glink_sbu>; >> + }; >> + }; >> + }; >> +}; > > i2c_master_hub > i2c0 > i2c_hub_2 > > The order doesn't seem to be correct. Ack > >> + >> +&ipa { >> + qcom,gsi-loader = "self"; >> + memory-region = <&ipa_fw_mem>; >> + firmware-name = "qcom/sm8550/ipa_fws.mbn"; >> + status = "okay"; >> +}; >> + >> +&gpu { >> + status = "okay"; >> + >> + zap-shader { >> + firmware-name = "qcom/sm8550/a740_zap.mbn"; >> + }; >> +}; > > This comes before i2c > >> + >> +&lpass_tlmm { >> + spkr_1_sd_n_active: spkr-1-sd-n-active-state { >> + pins = "gpio17"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + output-low; >> + }; >> + >> + spkr_2_sd_n_active: spkr-2-sd-n-active-state { >> + pins = "gpio18"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + output-low; >> + }; >> +}; >> + >> +&mdss { >> + status = "okay"; >> +}; >> + >> +&mdss_dsi0 { >> + vdda-supply = <&vreg_l3e_1p2>; >> + status = "okay"; >> +}; >> + >> +&mdss_dsi0_out { >> + remote-endpoint = <<9611_a>; >> + data-lanes = <0 1 2 3>; >> +}; >> + >> +&mdss_dsi0_phy { >> + vdds-supply = <&vreg_l1e_0p88>; >> + status = "okay"; >> +}; >> + >> +&mdss_dp0 { >> + status = "okay"; >> +}; >> + >> +&mdss_dp0_out { >> + remote-endpoint = <&usb_dp_qmpphy_dp_in>; >> + data-lanes = <0 1>; >> +}; >> + >> +&pcie0 { >> + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; >> + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; >> + >> + pinctrl-0 = <&pcie0_default_state>; >> + pinctrl-names = "default"; >> + >> + status = "okay"; >> +}; >> + >> +&pcie0_phy { >> + vdda-phy-supply = <&vreg_l1e_0p88>; >> + vdda-pll-supply = <&vreg_l3e_1p2>; >> + >> + status = "okay"; >> +}; >> + >> +&pcie1 { >> + wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; >> + perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>; >> + >> + pinctrl-0 = <&pcie1_default_state>; >> + pinctrl-names = "default"; >> + >> + status = "okay"; >> +}; >> + >> +&pcie1_phy { >> + vdda-phy-supply = <&vreg_l3c_0p9>; >> + vdda-pll-supply = <&vreg_l3e_1p2>; >> + vdda-qref-supply = <&vreg_l1e_0p88>; >> + >> + status = "okay"; >> +}; >> + >> +&pm8550_gpios { >> + sdc2_card_det_n: sdc2-card-det-state { >> + pins = "gpio12"; >> + function = "normal"; >> + input-enable; >> + output-disable; >> + bias-pull-up; >> + power-source = <1>; /* 1.8 V */ >> + }; >> + >> + volume_up_n: volume-up-n-state { >> + pins = "gpio6"; >> + function = "normal"; >> + power-source = <1>; >> + bias-pull-up; >> + input-enable; >> + }; >> +}; >> + >> +/* The RGB signals are routed to 3 separate LEDs on the HDK8550 */ >> +&pm8550_pwm { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + status = "okay"; >> + >> + led@1 { >> + reg = <1>; >> + function = LED_FUNCTION_STATUS; >> + color = <LED_COLOR_ID_RED>; >> + default-state = "off"; >> + }; >> + >> + led@2 { >> + reg = <2>; >> + function = LED_FUNCTION_STATUS; >> + color = <LED_COLOR_ID_GREEN>; >> + default-state = "off"; >> + }; >> + >> + led@3 { >> + reg = <3>; >> + function = LED_FUNCTION_STATUS; >> + color = <LED_COLOR_ID_BLUE>; >> + default-state = "off"; >> + }; >> +}; >> + >> +&pm8550b_eusb2_repeater { >> + vdd18-supply = <&vreg_l15b_1p8>; >> + vdd3-supply = <&vreg_l5b_3p1>; >> +}; >> + >> +&pon_pwrkey { >> + status = "okay"; >> +}; >> + >> +&pon_resin { >> + linux,code = <KEY_VOLUMEDOWN>; >> + >> + status = "okay"; >> +}; >> + >> +&pcie_1_phy_aux_clk { >> + clock-frequency = <1000>; >> +}; > > Next to other PCIe nodes? Indeed > >> + >> +&qupv3_id_0 { >> + status = "okay"; >> +}; >> + >> +&qupv3_id_1 { >> + status = "okay"; >> +}; > > BTW, don't we need to enable gpi_dma nodes for qup / i2c to work? Good question, for i2c_mater_hib no, but for i2c0 it should be enabled > >> + >> +&remoteproc_adsp { >> + firmware-name = "qcom/sm8550/adsp.mbn", >> + "qcom/sm8550/adsp_dtb.mbn"; >> + status = "okay"; >> +}; >> + >> +&remoteproc_cdsp { >> + firmware-name = "qcom/sm8550/cdsp.mbn", >> + "qcom/sm8550/cdsp_dtb.mbn"; >> + status = "okay"; >> +}; >> + >> +&remoteproc_mpss { >> + firmware-name = "qcom/sm8550/modem.mbn", >> + "qcom/sm8550/modem_dtb.mbn"; >> + status = "okay"; >> +}; >> + >> +&sdhc_2 { >> + cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>; >> + >> + pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>; >> + pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>; >> + pinctrl-names = "default", "sleep"; >> + >> + vmmc-supply = <&vreg_l9b_2p9>; >> + vqmmc-supply = <&vreg_l8b_1p8>; >> + >> + bus-width = <4>; >> + no-sdio; >> + no-mmc; >> + >> + status = "okay"; >> +}; >> + >> +&sleep_clk { >> + clock-frequency = <32000>; >> +}; >> + >> +&swr0 { >> + status = "okay"; >> + >> + /* WSA8845, Speaker North */ >> + north_spkr: speaker@0,0 { >> + compatible = "sdw20217020400"; >> + reg = <0 0>; >> + >> + pinctrl-0 = <&spkr_1_sd_n_active>; >> + pinctrl-names = "default"; >> + >> + powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>; >> + >> + vdd-1p8-supply = <&vreg_l15b_1p8>; >> + vdd-io-supply = <&vreg_l15b_1p8>; >> + >> + #sound-dai-cells = <0>; >> + sound-name-prefix = "SpkrLeft"; >> + }; >> + >> + /* WSA8845, Speaker South */ >> + south_spkr: speaker@0,1 { >> + compatible = "sdw20217020400"; >> + reg = <0 1>; >> + >> + pinctrl-0 = <&spkr_2_sd_n_active>; >> + pinctrl-names = "default"; >> + >> + powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>; >> + >> + vdd-1p8-supply = <&vreg_l15b_1p8>; >> + vdd-io-supply = <&vreg_l15b_1p8>; >> + >> + #sound-dai-cells = <0>; >> + sound-name-prefix = "SpkrRight"; >> + }; >> +}; >> + >> +&swr1 { >> + status = "okay"; >> + >> + /* WCD9385 RX */ >> + wcd_rx: codec@0,4 { >> + compatible = "sdw20217010d00"; >> + reg = <0 4>; >> + >> + qcom,rx-port-mapping = <1 2 3 4 5>; >> + }; >> +}; >> + >> +&swr2 { >> + status = "okay"; >> + >> + /* WCD9385 TX */ >> + wcd_tx: codec@0,3 { >> + compatible = "sdw20217010d00"; >> + reg = <0 3>; >> + >> + qcom,tx-port-mapping = <1 1 2 3>; >> + }; >> +}; >> + >> +&tlmm { >> + /* Reserved I/Os for NFC */ >> + gpio-reserved-ranges = <32 8>; >> + >> + bt_default: bt-default-state { >> + bt-en-pins { >> + pins = "gpio81"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + sw-ctrl-pins { >> + pins = "gpio82"; >> + function = "gpio"; >> + bias-pull-down; >> + }; >> + }; >> + >> + lt9611_irq_pin: lt9611-irq-state { >> + pins = "gpio8"; >> + function = "gpio"; >> + bias-disable; >> + }; >> + >> + lt9611_rst_pin: lt9611-rst-state { >> + pins = "gpio7"; >> + function = "gpio"; >> + output-high; >> + }; >> + >> + wcd_default: wcd-reset-n-active-state { >> + pins = "gpio108"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + output-low; >> + }; >> +}; >> + >> +&uart7 { >> + status = "okay"; >> +}; >> + >> +&uart14 { >> + status = "okay"; >> + >> + bluetooth { >> + compatible = "qcom,wcn7850-bt"; >> + >> + vddio-supply = <&vreg_l15b_1p8>; >> + vddaon-supply = <&vreg_s4e_0p95>; >> + vdddig-supply = <&vreg_s4e_0p95>; >> + vddrfa0p8-supply = <&vreg_s4e_0p95>; >> + vddrfa1p2-supply = <&vreg_s4g_1p25>; >> + vddrfa1p9-supply = <&vreg_s6g_1p86>; >> + >> + max-speed = <3200000>; >> + >> + enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>; >> + swctrl-gpios = <&tlmm 82 GPIO_ACTIVE_HIGH>; >> + >> + pinctrl-0 = <&bt_default>; >> + pinctrl-names = "default"; >> + }; >> +}; >> + >> +&ufs_mem_hc { >> + reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>; >> + >> + vcc-supply = <&vreg_l17b_2p5>; >> + vcc-max-microamp = <1300000>; >> + vccq-supply = <&vreg_l1g_1p2>; >> + vccq-max-microamp = <1200000>; >> + vdd-hba-supply = <&vreg_l3g_1p2>; >> + >> + status = "okay"; >> +}; >> + >> +&ufs_mem_phy { >> + vdda-phy-supply = <&vreg_l1d_0p88>; >> + vdda-pll-supply = <&vreg_l3e_1p2>; >> + >> + status = "okay"; >> +}; >> + >> +&usb_1 { >> + status = "okay"; >> +}; >> + >> +&usb_1_dwc3 { >> + dr_mode = "otg"; > > otg is a default I prefer keeping it, it makes it epxlicit > >> + usb-role-switch; >> +}; >> + >> +&usb_1_dwc3_hs { >> + remote-endpoint = <&pmic_glink_hs_in>; >> +}; >> + >> +&usb_1_dwc3_ss { >> + remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>; >> +}; >> + >> +&usb_1_hsphy { >> + vdd-supply = <&vreg_l1e_0p88>; >> + vdda12-supply = <&vreg_l3e_1p2>; >> + >> + phys = <&pm8550b_eusb2_repeater>; >> + >> + status = "okay"; >> +}; >> + >> +&usb_dp_qmpphy { >> + vdda-phy-supply = <&vreg_l3e_1p2>; >> + vdda-pll-supply = <&vreg_l3f_0p88>; >> + >> + orientation-switch; > > Shouldn't this property be moved to the base dtsi? I don't think so, I think it's a board feature, a board could have lanes switching on-board. > >> + >> + status = "okay"; >> +}; >> + >> +&usb_dp_qmpphy_dp_in { >> + remote-endpoint = <&mdss_dp0_out>; >> +}; >> + >> +&usb_dp_qmpphy_out { >> + remote-endpoint = <&pmic_glink_ss_in>; >> +}; >> + >> +&usb_dp_qmpphy_usb_ss_in { >> + remote-endpoint = <&usb_1_dwc3_ss>; >> +}; >> + >> +&xo_board { >> + clock-frequency = <76800000>; >> +}; >> >> -- >> 2.34.1 >> >> > > Thanks, Neil
On 23/01/2024 14:02, Neil Armstrong wrote: > On 23/01/2024 10:10, Dmitry Baryshkov wrote: >> On Tue, 23 Jan 2024 at 10:56, Neil Armstrong <neil.armstrong@linaro.org> wrote: >>> >>> The SM8550-HDK is an embedded development platforms for the >>> Snapdragon 8 Gen 2 SoC aka SM8550, with the following features: >>> - Qualcomm SM8550 SoC >>> - 16GiB On-board LPDDR5 >>> - On-board WiFi 7 + Bluetooth 5.3/BLE >>> - On-board UFS4.0 >>> - M.2 Key B+M Gen3x2 PCIe Slot >>> - HDMI Output >>> - USB-C Connector with DP Almode & Audio Accessory mode >>> - Micro-SDCard Slot >>> - Audio Jack with Playback and Microphone >>> - 2 On-board Analog microphones >>> - 2 On-board Speakers >>> - 96Boards Compatible Low-Speed and High-Speed connectors [1] >>>   - For Camera, Sensors and external Display cards >>>   - Compatible with the Linaro Debug board [2] >>> - SIM Slot for Modem >>> - Debug connectors >>> - 6x On-Board LEDs >>> >>> Product Page: [3] >>> >>> [1] https://www.96boards.org/specifications/ >>> [2] https://git.codelinaro.org/linaro/qcomlt/debugboard >>> [3] https://www.lantronix.com/products/snapdragon-8-gen-2-mobile-hardware-development-kit/ >>> >>> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> >>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> >>> --- >>>  arch/arm64/boot/dts/qcom/Makefile      |   1 + >>>  arch/arm64/boot/dts/qcom/sm8550-hdk.dts | 1290 +++++++++++++++++++++++++++++++ >>>  2 files changed, 1291 insertions(+) >>> >>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile >>> index 39889d5f8e12..42e50f2b2ec3 100644 >>> --- a/arch/arm64/boot/dts/qcom/Makefile >>> +++ b/arch/arm64/boot/dts/qcom/Makefile >>> @@ -233,6 +233,7 @@ dtb-$(CONFIG_ARCH_QCOM)    += sm8450-hdk.dtb >>>  dtb-$(CONFIG_ARCH_QCOM)       += sm8450-qrd.dtb >>>  dtb-$(CONFIG_ARCH_QCOM)       += sm8450-sony-xperia-nagara-pdx223.dtb >>>  dtb-$(CONFIG_ARCH_QCOM)       += sm8450-sony-xperia-nagara-pdx224.dtb >>> +dtb-$(CONFIG_ARCH_QCOM)       += sm8550-hdk.dtb >>>  dtb-$(CONFIG_ARCH_QCOM)       += sm8550-mtp.dtb >>>  dtb-$(CONFIG_ARCH_QCOM)       += sm8550-qrd.dtb >>>  dtb-$(CONFIG_ARCH_QCOM)       += sm8650-mtp.dtb >>> diff --git a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts >>> new file mode 100644 >>> index 000000000000..66bdd6c269ea >>> --- /dev/null >>> +++ b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts >>> @@ -0,0 +1,1290 @@ <snip> > >> >>> + >>> +&qupv3_id_0 { >>> +      status = "okay"; >>> +}; >>> + >>> +&qupv3_id_1 { >>> +      status = "okay"; >>> +}; >> >> BTW, don't we need to enable gpi_dma nodes for qup / i2c to work? > > Good question, for i2c_mater_hib no, but for i2c0 it should be enabled OK I understood, i2c0 is configured to use FIFO so not having gpi dma enabled doesn't fail. I'll still enable it. Neil <snip>
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 39889d5f8e12..42e50f2b2ec3 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -233,6 +233,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8450-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx223.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts new file mode 100644 index 000000000000..66bdd6c269ea --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts @@ -0,0 +1,1290 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Linaro Limited + */ + +/dts-v1/; + +#include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sm8550.dtsi" +#include "pm8010.dtsi" +#include "pm8550.dtsi" +#include "pm8550b.dtsi" +#define PMK8550VE_SID 5 +#include "pm8550ve.dtsi" +#include "pm8550vs.dtsi" +#include "pmk8550.dtsi" +#include "pmr735d_a.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SM8550 HDK"; + compatible = "qcom,sm8550-hdk", "qcom,sm8550"; + chassis-type = "embedded"; + + aliases { + serial0 = &uart7; + serial1 = &uart14; + }; + + wcd938x: audio-codec { + compatible = "qcom,wcd9385-codec"; + + pinctrl-names = "default"; + pinctrl-0 = <&wcd_default>; + + qcom,micbias1-microvolt = <1800000>; + qcom,micbias2-microvolt = <1800000>; + qcom,micbias3-microvolt = <1800000>; + qcom,micbias4-microvolt = <1800000>; + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; + qcom,rx-device = <&wcd_rx>; + qcom,tx-device = <&wcd_tx>; + + reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>; + + vdd-buck-supply = <&vreg_l15b_1p8>; + vdd-rxtx-supply = <&vreg_l15b_1p8>; + vdd-io-supply = <&vreg_l15b_1p8>; + vdd-mic-bias-supply = <&vreg_bob1>; + + #sound-dai-cells = <1>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_out: endpoint { + remote-endpoint = <<9611_out>; + }; + }; + }; + + vreg_bob_3v3: vreg-bob-3v3-regulator { + compatible = "regulator-fixed"; + + regulator-name = "VREG_BOB_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&vph_pwr>; + }; + + lt9611_1v2: lt9611-vdd12-regulator { + compatible = "regulator-fixed"; + + regulator-name = "LT9611_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + vin-supply = <&vph_pwr>; + gpio = <&tlmm 152 GPIO_ACTIVE_HIGH>; + + enable-active-high; + }; + + lt9611_3v3: lt9611-3v3-regulator { + compatible = "regulator-fixed"; + + regulator-name = "LT9611_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&vreg_bob_3v3>; + gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>; + + enable-active-high; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&volume_up_n>; + pinctrl-names = "default"; + + key-volume-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + function = LED_FUNCTION_BLUETOOTH; + color = <LED_COLOR_ID_BLUE>; + gpios = <&tlmm 159 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "bluetooth-power"; + default-state = "off"; + }; + + led-1 { + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_GREEN>; + gpios = <&tlmm 160 GPIO_ACTIVE_HIGH>; + default-state = "off"; + panic-indicator; + }; + + led-2 { + function = LED_FUNCTION_WLAN; + color = <LED_COLOR_ID_ORANGE>; + gpios = <&tlmm 162 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; + default-state = "off"; + }; + }; + + pmic-glink { + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink"; + #address-cells = <1>; + #size-cells = <0>; + orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; + + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_hs_in: endpoint { + remote-endpoint = <&usb_1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss_in: endpoint { + remote-endpoint = <&usb_dp_qmpphy_out>; + }; + }; + + port@2 { + reg = <2>; + + pmic_glink_sbu: endpoint { + remote-endpoint = <&fsa4480_sbu_mux>; + }; + }; + }; + }; + }; + + sound { + compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard"; + model = "SM8550-HDK"; + audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT", + "SpkrRight IN", "WSA_SPK2 OUT", + "IN1_HPHL", "HPHL_OUT", + "IN2_HPHR", "HPHR_OUT", + "AMIC1", "MIC BIAS1", + "AMIC2", "MIC BIAS2", + "AMIC5", "MIC BIAS4", + "TX SWR_ADC0", "ADC1_OUTPUT", + "TX SWR_ADC1", "ADC2_OUTPUT", + "TX SWR_ADC3", "ADC4_OUTPUT"; + + + wcd-playback-dai-link { + link-name = "WCD Playback"; + + cpu { + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; + }; + + codec { + sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; + }; + + platform { + sound-dai = <&q6apm>; + }; + }; + + wcd-capture-dai-link { + link-name = "WCD Capture"; + + cpu { + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; + }; + + codec { + sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>; + }; + + platform { + sound-dai = <&q6apm>; + }; + }; + + wsa-dai-link { + link-name = "WSA Playback"; + + cpu { + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; + }; + + codec { + sound-dai = <&north_spkr>, <&south_spkr>, <&swr0 0>, <&lpass_wsamacro 0>; + }; + + platform { + sound-dai = <&q6apm>; + }; + }; + + va-dai-link { + link-name = "VA Capture"; + + cpu { + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; + }; + + codec { + sound-dai = <&lpass_vamacro 0>; + }; + + platform { + sound-dai = <&q6apm>; + }; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + + vdd-bob1-supply = <&vph_pwr>; + vdd-bob2-supply = <&vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l3-supply = <&vreg_s4g_1p25>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob1>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l11-supply = <&vreg_s4g_1p25>; + vdd-l12-supply = <&vreg_s6g_1p86>; + vdd-l15-supply = <&vreg_s6g_1p86>; + vdd-l17-supply = <&vreg_bob2>; + + qcom,pmic-id = "b"; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3296000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2720000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1b_1p8: ldo1 { + regulator-name = "vreg_l1b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5b_3p1: ldo5 { + regulator-name = "vreg_l5b_3p1"; + regulator-min-microvolt = <3104000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7b_1p8: ldo7 { + regulator-name = "vreg_l7b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_1p8: ldo8 { + regulator-name = "vreg_l8b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11b_1p2: ldo11 { + regulator-name = "vreg_l11b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p8: ldo12 { + regulator-name = "vreg_l12b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p2: ldo14 { + regulator-name = "vreg_l14b_3p2"; + regulator-min-microvolt = <3200000>; + regulator-max-microvolt = <3200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16b_2p8: ldo16 { + regulator-name = "vreg_l16b_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s4g_1p25>; + vdd-l2-supply = <&vreg_s4e_0p95>; + vdd-l3-supply = <&vreg_s4e_0p95>; + + qcom,pmic-id = "c"; + + vreg_l3c_0p9: ldo3 { + regulator-name = "vreg_l3c_0p9"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s4e_0p95>; + vdd-l2-supply = <&vreg_s4e_0p95>; + vdd-l3-supply = <&vreg_s4e_0p95>; + + qcom,pmic-id = "d"; + + vreg_l1d_0p88: ldo1 { + regulator-name = "vreg_l1d_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + /* ldo2 supplies SM8550 VDD_LPI_MX */ + }; + + regulators-3 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s4e_0p95>; + vdd-l2-supply = <&vreg_s4e_0p95>; + vdd-l3-supply = <&vreg_s4g_1p25>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + + qcom,pmic-id = "e"; + + vreg_s4e_0p95: smps4 { + regulator-name = "vreg_s4e_0p95"; + regulator-min-microvolt = <904000>; + regulator-max-microvolt = <984000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5e_1p08: smps5 { + regulator-name = "vreg_s5e_1p08"; + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1120000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1e_0p88: ldo1 { + regulator-name = "vreg_l1e_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2e_0p9: ldo2 { + regulator-name = "vreg_l2e_0p9"; + regulator-min-microvolt = <904000>; + regulator-max-microvolt = <970000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s4e_0p95>; + vdd-l2-supply = <&vreg_s4e_0p95>; + vdd-l3-supply = <&vreg_s4e_0p95>; + vdd-s4-supply = <&vph_pwr>; + + qcom,pmic-id = "f"; + + vreg_s4f_0p5: smps4 { + regulator-name = "vreg_s4f_0p5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <700000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1f_0p9: ldo1 { + regulator-name = "vreg_l1f_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2f_0p88: ldo2 { + regulator-name = "vreg_l2f_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3f_0p88: ldo3 { + regulator-name = "vreg_l3f_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-5 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s4g_1p25>; + vdd-l2-supply = <&vreg_s4g_1p25>; + vdd-l3-supply = <&vreg_s4g_1p25>; + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + + qcom,pmic-id = "g"; + + vreg_s1g_1p25: smps1 { + regulator-name = "vreg_s1g_1p25"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2g_0p85: smps2 { + regulator-name = "vreg_s2g_0p85"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s3g_0p8: smps3 { + regulator-name = "vreg_s3g_0p8"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1004000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4g_1p25: smps4 { + regulator-name = "vreg_s4g_1p25"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1352000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5g_0p85: smps5 { + regulator-name = "vreg_s5g_0p85"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1004000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s6g_1p86: smps6 { + regulator-name = "vreg_s6g_1p86"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1g_1p2: ldo1 { + regulator-name = "vreg_l1g_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3g_1p2: ldo3 { + regulator-name = "vreg_l3g_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8010-rpmh-regulators"; + + vdd-l1-l2-supply = <&vreg_s4g_1p25>; + vdd-l3-l4-supply = <&vreg_bob2>; + vdd-l5-supply = <&vreg_s6g_1p86>; + vdd-l6-supply = <&vreg_s6g_1p86>; + vdd-l7-supply = <&vreg_bob1>; + + qcom,pmic-id = "m"; + + vreg_l1m_1p056: ldo1 { + regulator-name = "vreg_l1m_1p056"; + regulator-min-microvolt = <1056000>; + regulator-max-microvolt = <1056000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2m_1p056: ldo2 { + regulator-name = "vreg_l2m_1p056"; + regulator-min-microvolt = <1056000>; + regulator-max-microvolt = <1056000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3m_2p8: ldo3 { + regulator-name = "vreg_l3m_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4m_2p8: ldo4 { + regulator-name = "vreg_l4m_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5m_1p8: ldo5 { + regulator-name = "vreg_l5m_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6m_1p8: ldo6 { + regulator-name = "vreg_l6m_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7m_2p9: ldo7 { + regulator-name = "vreg_l7m_2p9"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8010-rpmh-regulators"; + + vdd-l1-l2-supply = <&vreg_s4g_1p25>; + vdd-l3-l4-supply = <&vreg_bob2>; + vdd-l5-supply = <&vreg_s6g_1p86>; + vdd-l6-supply = <&vreg_bob1>; + vdd-l7-supply = <&vreg_bob1>; + + qcom,pmic-id = "n"; + + vreg_l1n_1p1: ldo1 { + regulator-name = "vreg_l1n_1p1"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2n_1p1: ldo2 { + regulator-name = "vreg_l2n_1p1"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3n_2p8: ldo3 { + regulator-name = "vreg_l3n_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4n_2p8: ldo4 { + regulator-name = "vreg_l4n_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5n_1p8: ldo5 { + regulator-name = "vreg_l5n_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6n_3p3: ldo6 { + regulator-name = "vreg_l6n_3p3"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7n_2p96: ldo7 { + regulator-name = "vreg_l7n_2p96"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&i2c_master_hub_0 { + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + lt9611_codec: hdmi-bridge@2b { + compatible = "lontium,lt9611uxc"; + reg = <0x2b>; + + interrupts-extended = <&tlmm 8 IRQ_TYPE_EDGE_FALLING>; + + reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>; + + vdd-supply = <<9611_1v2>; + vcc-supply = <<9611_3v3>; + + pinctrl-0 = <<9611_irq_pin>, <<9611_rst_pin>; + pinctrl-names = "default"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lt9611_a: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + lt9611_out: endpoint { + remote-endpoint = <&hdmi_connector_out>; + }; + }; + }; + }; +}; + +&i2c_hub_2 { + status = "okay"; + + typec-mux@42 { + compatible = "fcs,fsa4480"; + reg = <0x42>; + + vcc-supply = <&vreg_bob1>; + + mode-switch; + orientation-switch; + + port { + fsa4480_sbu_mux: endpoint { + remote-endpoint = <&pmic_glink_sbu>; + }; + }; + }; +}; + +&ipa { + qcom,gsi-loader = "self"; + memory-region = <&ipa_fw_mem>; + firmware-name = "qcom/sm8550/ipa_fws.mbn"; + status = "okay"; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/sm8550/a740_zap.mbn"; + }; +}; + +&lpass_tlmm { + spkr_1_sd_n_active: spkr-1-sd-n-active-state { + pins = "gpio17"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-low; + }; + + spkr_2_sd_n_active: spkr-2-sd-n-active-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-low; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l3e_1p2>; + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <<9611_a>; + data-lanes = <0 1 2 3>; +}; + +&mdss_dsi0_phy { + vdds-supply = <&vreg_l1e_0p88>; + status = "okay"; +}; + +&mdss_dp0 { + status = "okay"; +}; + +&mdss_dp0_out { + remote-endpoint = <&usb_dp_qmpphy_dp_in>; + data-lanes = <0 1>; +}; + +&pcie0 { + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie0_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie0_phy { + vdda-phy-supply = <&vreg_l1e_0p88>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie1 { + wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; + perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie1_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie1_phy { + vdda-phy-supply = <&vreg_l3c_0p9>; + vdda-pll-supply = <&vreg_l3e_1p2>; + vdda-qref-supply = <&vreg_l1e_0p88>; + + status = "okay"; +}; + +&pm8550_gpios { + sdc2_card_det_n: sdc2-card-det-state { + pins = "gpio12"; + function = "normal"; + input-enable; + output-disable; + bias-pull-up; + power-source = <1>; /* 1.8 V */ + }; + + volume_up_n: volume-up-n-state { + pins = "gpio6"; + function = "normal"; + power-source = <1>; + bias-pull-up; + input-enable; + }; +}; + +/* The RGB signals are routed to 3 separate LEDs on the HDK8550 */ +&pm8550_pwm { + #address-cells = <1>; + #size-cells = <0>; + + status = "okay"; + + led@1 { + reg = <1>; + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_RED>; + default-state = "off"; + }; + + led@2 { + reg = <2>; + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + default-state = "off"; + }; + + led@3 { + reg = <3>; + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_BLUE>; + default-state = "off"; + }; +}; + +&pm8550b_eusb2_repeater { + vdd18-supply = <&vreg_l15b_1p8>; + vdd3-supply = <&vreg_l5b_3p1>; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + + status = "okay"; +}; + +&pcie_1_phy_aux_clk { + clock-frequency = <1000>; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/sm8550/adsp.mbn", + "qcom/sm8550/adsp_dtb.mbn"; + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/sm8550/cdsp.mbn", + "qcom/sm8550/cdsp_dtb.mbn"; + status = "okay"; +}; + +&remoteproc_mpss { + firmware-name = "qcom/sm8550/modem.mbn", + "qcom/sm8550/modem_dtb.mbn"; + status = "okay"; +}; + +&sdhc_2 { + cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>; + pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>; + pinctrl-names = "default", "sleep"; + + vmmc-supply = <&vreg_l9b_2p9>; + vqmmc-supply = <&vreg_l8b_1p8>; + + bus-width = <4>; + no-sdio; + no-mmc; + + status = "okay"; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&swr0 { + status = "okay"; + + /* WSA8845, Speaker North */ + north_spkr: speaker@0,0 { + compatible = "sdw20217020400"; + reg = <0 0>; + + pinctrl-0 = <&spkr_1_sd_n_active>; + pinctrl-names = "default"; + + powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>; + + vdd-1p8-supply = <&vreg_l15b_1p8>; + vdd-io-supply = <&vreg_l15b_1p8>; + + #sound-dai-cells = <0>; + sound-name-prefix = "SpkrLeft"; + }; + + /* WSA8845, Speaker South */ + south_spkr: speaker@0,1 { + compatible = "sdw20217020400"; + reg = <0 1>; + + pinctrl-0 = <&spkr_2_sd_n_active>; + pinctrl-names = "default"; + + powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>; + + vdd-1p8-supply = <&vreg_l15b_1p8>; + vdd-io-supply = <&vreg_l15b_1p8>; + + #sound-dai-cells = <0>; + sound-name-prefix = "SpkrRight"; + }; +}; + +&swr1 { + status = "okay"; + + /* WCD9385 RX */ + wcd_rx: codec@0,4 { + compatible = "sdw20217010d00"; + reg = <0 4>; + + qcom,rx-port-mapping = <1 2 3 4 5>; + }; +}; + +&swr2 { + status = "okay"; + + /* WCD9385 TX */ + wcd_tx: codec@0,3 { + compatible = "sdw20217010d00"; + reg = <0 3>; + + qcom,tx-port-mapping = <1 1 2 3>; + }; +}; + +&tlmm { + /* Reserved I/Os for NFC */ + gpio-reserved-ranges = <32 8>; + + bt_default: bt-default-state { + bt-en-pins { + pins = "gpio81"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + sw-ctrl-pins { + pins = "gpio82"; + function = "gpio"; + bias-pull-down; + }; + }; + + lt9611_irq_pin: lt9611-irq-state { + pins = "gpio8"; + function = "gpio"; + bias-disable; + }; + + lt9611_rst_pin: lt9611-rst-state { + pins = "gpio7"; + function = "gpio"; + output-high; + }; + + wcd_default: wcd-reset-n-active-state { + pins = "gpio108"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-low; + }; +}; + +&uart7 { + status = "okay"; +}; + +&uart14 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn7850-bt"; + + vddio-supply = <&vreg_l15b_1p8>; + vddaon-supply = <&vreg_s4e_0p95>; + vdddig-supply = <&vreg_s4e_0p95>; + vddrfa0p8-supply = <&vreg_s4e_0p95>; + vddrfa1p2-supply = <&vreg_s4g_1p25>; + vddrfa1p9-supply = <&vreg_s6g_1p86>; + + max-speed = <3200000>; + + enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>; + swctrl-gpios = <&tlmm 82 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&bt_default>; + pinctrl-names = "default"; + }; +}; + +&ufs_mem_hc { + reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l17b_2p5>; + vcc-max-microamp = <1300000>; + vccq-supply = <&vreg_l1g_1p2>; + vccq-max-microamp = <1200000>; + vdd-hba-supply = <&vreg_l3g_1p2>; + + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l1d_0p88>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "otg"; + usb-role-switch; +}; + +&usb_1_dwc3_hs { + remote-endpoint = <&pmic_glink_hs_in>; +}; + +&usb_1_dwc3_ss { + remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>; +}; + +&usb_1_hsphy { + vdd-supply = <&vreg_l1e_0p88>; + vdda12-supply = <&vreg_l3e_1p2>; + + phys = <&pm8550b_eusb2_repeater>; + + status = "okay"; +}; + +&usb_dp_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l3f_0p88>; + + orientation-switch; + + status = "okay"; +}; + +&usb_dp_qmpphy_dp_in { + remote-endpoint = <&mdss_dp0_out>; +}; + +&usb_dp_qmpphy_out { + remote-endpoint = <&pmic_glink_ss_in>; +}; + +&usb_dp_qmpphy_usb_ss_in { + remote-endpoint = <&usb_1_dwc3_ss>; +}; + +&xo_board { + clock-frequency = <76800000>; +};