| Message ID | 20240401-sy7802-v2-2-1138190a7448@apitzsch.eu (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add sy7802 flash led driver | expand |
On Mon, 01 Apr 2024, André Apitzsch via B4 Relay wrote: > From: André Apitzsch <git@apitzsch.eu> > > Add support for SY7802 flash LED controller. It can support up to 1.8A > flash current. This is a very small commit message for a 500+ line change! Please, tell us more. > Signed-off-by: André Apitzsch <git@apitzsch.eu> > --- > drivers/leds/flash/Kconfig | 11 + > drivers/leds/flash/Makefile | 1 + > drivers/leds/flash/leds-sy7802.c | 532 +++++++++++++++++++++++++++++++++++++++ > 3 files changed, 544 insertions(+) > > diff --git a/drivers/leds/flash/Kconfig b/drivers/leds/flash/Kconfig > index 809b6d98bb3e..f39f0bfe6eef 100644 > --- a/drivers/leds/flash/Kconfig > +++ b/drivers/leds/flash/Kconfig > @@ -121,4 +121,15 @@ config LEDS_SGM3140 > This option enables support for the SGM3140 500mA Buck/Boost Charge > Pump LED Driver. > > +config LEDS_SY7802 > + tristate "LED support for the Silergy SY7802" > + depends on I2C && OF > + depends on GPIOLIB > + select REGMAP_I2C > + help > + This option enables support for the SY7802 flash LED controller. > + SY7802 includes torch and flash functions with programmable current. > + > + This driver can be built as a module, it will be called "leds-sy7802". > + > endif # LEDS_CLASS_FLASH > diff --git a/drivers/leds/flash/Makefile b/drivers/leds/flash/Makefile > index 91d60a4b7952..48860eeced79 100644 > --- a/drivers/leds/flash/Makefile > +++ b/drivers/leds/flash/Makefile > @@ -11,3 +11,4 @@ obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom-flash.o > obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o > obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o > obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o > +obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o > diff --git a/drivers/leds/flash/leds-sy7802.c b/drivers/leds/flash/leds-sy7802.c > new file mode 100644 > index 000000000000..c03a571b0e08 > --- /dev/null > +++ b/drivers/leds/flash/leds-sy7802.c > @@ -0,0 +1,532 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* > + * Silergy SY7802 flash LED driver with I2C interface > + * > + * Copyright 2024 André Apitzsch <git@apitzsch.eu> > + */ > + > +#include <linux/gpio/consumer.h> > +#include <linux/i2c.h> > +#include <linux/kernel.h> > +#include <linux/led-class-flash.h> > +#include <linux/module.h> > +#include <linux/mutex.h> > +#include <linux/regmap.h> > +#include <linux/regulator/consumer.h> > + > +#define SY7802_MAX_LEDS 2 > +#define SY7802_LED_JOINT 2 > + > +#define SY7802_REG_ENABLE 0x10 > +#define SY7802_REG_TORCH_BRIGHTNESS 0xa0 > +#define SY7802_REG_FLASH_BRIGHTNESS 0xb0 > +#define SY7802_REG_FLASH_DURATION 0xc0 > +#define SY7802_REG_FLAGS 0xd0 > +#define SY7802_REG_CONFIG_1 0xe0 > +#define SY7802_REG_CONFIG_2 0xf0 > +#define SY7802_REG_VIN_MONITOR 0x80 > +#define SY7802_REG_LAST_FLASH 0x81 > +#define SY7802_REG_VLED_MONITOR 0x30 > +#define SY7802_REG_ADC_DELAY 0x31 > +#define SY7802_REG_DEV_ID 0xff > + > +#define SY7802_MODE_OFF 0 > +#define SY7802_MODE_TORCH 2 > +#define SY7802_MODE_FLASH 3 > +#define SY7802_MODE_MASK GENMASK(1, 0) > + > +#define SY7802_LEDS_SHIFT 3 > +#define SY7802_LEDS_MASK(_id) (BIT(_id) << SY7802_LEDS_SHIFT) > +#define SY7802_LEDS_MASK_ALL (SY7802_LEDS_MASK(0) | SY7802_LEDS_MASK(1)) > + > +#define SY7802_TORCH_CURRENT_SHIFT 3 > +#define SY7802_TORCH_CURRENT_MASK(_id) \ > + (GENMASK(2, 0) << (SY7802_TORCH_CURRENT_SHIFT * (_id))) > +#define SY7802_TORCH_CURRENT_MASK_ALL \ > + (SY7802_TORCH_CURRENT_MASK(0) | SY7802_TORCH_CURRENT_MASK(1)) > + > +#define SY7802_FLASH_CURRENT_SHIFT 4 > +#define SY7802_FLASH_CURRENT_MASK(_id) \ > + (GENMASK(3, 0) << (SY7802_FLASH_CURRENT_SHIFT * (_id))) > +#define SY7802_FLASH_CURRENT_MASK_ALL \ > + (SY7802_FLASH_CURRENT_MASK(0) | SY7802_FLASH_CURRENT_MASK(1)) > + > +#define SY7802_TIMEOUT_DEFAULT_US 512000U > +#define SY7802_TIMEOUT_MIN_US 32000U > +#define SY7802_TIMEOUT_MAX_US 1024000U > +#define SY7802_TIMEOUT_STEPSIZE_US 32000U > + > +#define SY7802_TORCH_BRIGHTNESS_MAX 8 > + > +#define SY7802_FLASH_BRIGHTNESS_DEFAULT 14 > +#define SY7802_FLASH_BRIGHTNESS_MIN 0 > +#define SY7802_FLASH_BRIGHTNESS_MAX 15 > +#define SY7802_FLASH_BRIGHTNESS_STEP 1 Much nicer to read if everything was aligned. > +#define SY7802_FLAG_TIMEOUT (1 << 0) > +#define SY7802_FLAG_THERMAL_SHUTDOWN (1 << 1) > +#define SY7802_FLAG_LED_FAULT (1 << 2) > +#define SY7802_FLAG_TX1_INTERRUPT (1 << 3) > +#define SY7802_FLAG_TX2_INTERRUPT (1 << 4) > +#define SY7802_FLAG_LED_THERMAL_FAULT (1 << 5) > +#define SY7802_FLAG_FLASH_INPUT_VOLTAGE_LOW (1 << 6) > +#define SY7802_FLAG_INPUT_VOLTAGE_LOW (1 << 7) Why not BIT()? > +#define SY7802_CHIP_ID 0x51 > + > +static const struct reg_default sy7802_regmap_defs[] = { > + { SY7802_REG_ENABLE, SY7802_LEDS_MASK_ALL }, > + { SY7802_REG_TORCH_BRIGHTNESS, 0x92 }, > + { SY7802_REG_FLASH_BRIGHTNESS, SY7802_FLASH_BRIGHTNESS_DEFAULT | > + SY7802_FLASH_BRIGHTNESS_DEFAULT << SY7802_FLASH_CURRENT_SHIFT }, > + { SY7802_REG_FLASH_DURATION, 0x6f }, > + { SY7802_REG_FLAGS, 0x0 }, > + { SY7802_REG_CONFIG_1, 0x68 }, > + { SY7802_REG_CONFIG_2, 0xf0 }, > +}; > + > +struct sy7802_led { > + struct led_classdev_flash flash; > + struct sy7802 *chip; > + u8 led_no; Is this LED number or no LED? How about led_num or led_id? > +}; > + > +struct sy7802 { > + struct mutex mutex; Place the big stuff (like struct device and regmap at the top). > + struct device *dev; > + struct regmap *regmap; > + > + struct gpio_desc *enable_gpio; > + struct regulator *vin_regulator; > + > + unsigned int fled_strobe_used; > + unsigned int fled_torch_used; > + unsigned int leds_active; > + int num_leds; > + struct sy7802_led leds[] __counted_by(num_leds); > +}; > + > +static int sy7802_torch_brightness_set(struct led_classdev *lcdev, enum led_brightness level) s/level/brightness/ > +{ > + struct sy7802_led *led = container_of(lcdev, struct sy7802_led, flash.led_cdev); > + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? SY7802_LEDS_MASK_ALL : > + SY7802_LEDS_MASK(led->led_no); Do all of the fancy multi-line assignment outside of the declaration block. > + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; > + u32 val = level ? led_enable_mask : SY7802_MODE_OFF; > + struct sy7802 *chip = led->chip; > + u32 curr; This is a temporary placeholder for fled_torch_used, right? fled_torch_used_tmp? Sometimes abbreviated to tmp. > + u32 mask; That's a lot of masks. Which one is this? > + int ret; > + > + mutex_lock(&chip->mutex); > + > + /* > + * There is only one set of flash control logic, and this flag is used to check if 'strobe' The ',' before 'and' is superfluous. > + * is currently being used. > + */ Doesn't the variable name kind of imply this? > + if (chip->fled_strobe_used) { > + dev_warn(chip->dev, "Please disable strobe first [%d]\n", chip->fled_strobe_used); "Cannot set torch brightness whilst strobe is enabled" > + ret = -EBUSY; > + goto unlock; > + } > + > + if (level) > + curr = chip->fled_torch_used | BIT(led->led_no); > + else > + curr = chip->fled_torch_used & ~BIT(led->led_no); > + > + if (curr) > + val |= SY7802_MODE_TORCH; > + > + /* Torch needs to be disabled first to apply new brightness */ "Disable touch to apply brightness" > + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, SY7802_MODE_MASK, > + SY7802_MODE_OFF); > + if (ret) > + goto unlock; > + > + mask = led->led_no == SY7802_LED_JOINT ? SY7802_TORCH_CURRENT_MASK_ALL : Why not just use led->led_no in place of mask? Easier to read if you drop SY7802_TORCH_CURRENT_MASK_ALL to its own line. > + SY7802_TORCH_CURRENT_MASK(led->led_no); > + > + /* Register expects brightness between 0 and MAX_BRIGHTNESS - 1 */ > + if (level) > + level -= 1; > + > + level |= (level << SY7802_TORCH_CURRENT_SHIFT); > + > + ret = regmap_update_bits(chip->regmap, SY7802_REG_TORCH_BRIGHTNESS, mask, level); > + if (ret) > + goto unlock; > + > + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, enable_mask, val); > + if (ret) > + goto unlock; > + > + chip->fled_torch_used = curr; > + > +unlock: > + mutex_unlock(&chip->mutex); > + return ret; > +} > + > +static int sy7802_flash_brightness_set(struct led_classdev_flash *fl_cdev, u32 brightness) > +{ > + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); > + struct led_flash_setting *s = &fl_cdev->brightness; > + u32 val = (brightness - s->min) / s->step; > + struct sy7802 *chip = led->chip; > + u32 mask; > + int ret; > + > + val |= (val << SY7802_FLASH_CURRENT_SHIFT); > + mask = led->led_no == SY7802_LED_JOINT ? SY7802_FLASH_CURRENT_MASK_ALL : > + SY7802_FLASH_CURRENT_MASK(led->led_no); > + > + mutex_lock(&chip->mutex); > + ret = regmap_update_bits(chip->regmap, SY7802_REG_FLASH_BRIGHTNESS, mask, val); > + mutex_unlock(&chip->mutex); > + > + return ret; > +} > + > +static int sy7802_strobe_set(struct led_classdev_flash *fl_cdev, bool state) Same comments as above apply throughout the driver. > +{ > + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); > + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? SY7802_LEDS_MASK_ALL : > + SY7802_LEDS_MASK(led->led_no); > + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; > + u32 val = state ? led_enable_mask : SY7802_MODE_OFF; > + struct sy7802 *chip = led->chip; > + u32 curr; > + int ret; > + > + mutex_lock(&chip->mutex); > + > + /* > + * There is only one set of flash control logic, and this flag is used to check if 'torch' > + * is currently being used. > + */ > + if (chip->fled_torch_used) { > + dev_warn(chip->dev, "Please disable torch first [0x%x]\n", chip->fled_torch_used); > + ret = -EBUSY; > + goto unlock; > + } > + > + if (state) > + curr = chip->fled_strobe_used | BIT(led->led_no); > + else > + curr = chip->fled_strobe_used & ~BIT(led->led_no); > + > + if (curr) > + val |= SY7802_MODE_FLASH; > + > + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, enable_mask, val); > + > + if (ret) > + goto unlock; > + > + chip->fled_strobe_used = curr; > + > +unlock: > + mutex_unlock(&chip->mutex); > + return ret; > +} > + > +static int sy7802_strobe_get(struct led_classdev_flash *fl_cdev, bool *state) > +{ > + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); > + struct sy7802 *chip = led->chip; > + > + mutex_lock(&chip->mutex); > + *state = !!(chip->fled_strobe_used & BIT(led->led_no)); > + mutex_unlock(&chip->mutex); > + > + return 0; > +} > + > +static int sy7802_timeout_set(struct led_classdev_flash *fl_cdev, > + u32 timeout) > +{ > + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); > + struct led_flash_setting *s = &fl_cdev->timeout; > + u32 val = (timeout - s->min) / s->step; > + struct sy7802 *chip = led->chip; > + > + return regmap_write(chip->regmap, SY7802_REG_FLASH_DURATION, val); > +} > + > +static int sy7802_fault_get(struct led_classdev_flash *fl_cdev, u32 *fault) > +{ > + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); > + struct sy7802 *chip = led->chip; > + u32 val, led_faults = 0; > + int ret; > + > + /* NOTE: reading register clears fault status */ > + ret = regmap_read(chip->regmap, SY7802_REG_FLAGS, &val); > + if (ret) > + return ret; > + > + if (val & (SY7802_FLAG_FLASH_INPUT_VOLTAGE_LOW | SY7802_FLAG_INPUT_VOLTAGE_LOW)) > + led_faults |= LED_FAULT_INPUT_VOLTAGE; > + > + if (val & SY7802_FLAG_THERMAL_SHUTDOWN) > + led_faults |= LED_FAULT_OVER_TEMPERATURE; > + > + if (val & SY7802_FLAG_TIMEOUT) > + led_faults |= LED_FAULT_TIMEOUT; > + > + *fault = led_faults; > + return 0; > +} > + > +static const struct led_flash_ops sy7802_flash_ops = { > + .flash_brightness_set = sy7802_flash_brightness_set, > + .strobe_set = sy7802_strobe_set, > + .strobe_get = sy7802_strobe_get, > + .timeout_set = sy7802_timeout_set, > + .fault_get = sy7802_fault_get, > +}; > + > +static void sy7802_init_flash_brightness(struct led_classdev_flash *fl_cdev) > +{ > + struct led_flash_setting *s; > + > + /* Init flash brightness setting */ > + s = &fl_cdev->brightness; > + s->min = SY7802_FLASH_BRIGHTNESS_MIN; > + s->max = SY7802_FLASH_BRIGHTNESS_MAX; > + s->step = SY7802_FLASH_BRIGHTNESS_STEP; > + s->val = SY7802_FLASH_BRIGHTNESS_DEFAULT; > +} > + > +static void sy7802_init_flash_timeout(struct led_classdev_flash *fl_cdev) > +{ > + struct led_flash_setting *s; > + > + /* Init flash timeout setting */ > + s = &fl_cdev->timeout; > + s->min = SY7802_TIMEOUT_MIN_US; > + s->max = SY7802_TIMEOUT_MAX_US; > + s->step = SY7802_TIMEOUT_STEPSIZE_US; > + s->val = SY7802_TIMEOUT_DEFAULT_US; > +} > + > +static int sy7802_led_register(struct device *dev, struct sy7802_led *led, > + struct device_node *np) > +{ > + struct led_init_data init_data = {}; > + int ret; > + > + init_data.fwnode = of_fwnode_handle(np); > + > + ret = devm_led_classdev_flash_register_ext(dev, &led->flash, &init_data); > + if (ret) { > + dev_err(dev, "Couldn't register flash %d\n", led->led_no); > + return ret; > + } > + > + return ret; > +} > + > +static int sy7802_init_flash_properties(struct device *dev, struct sy7802_led *led, > + struct device_node *np) > +{ > + struct led_classdev_flash *flash = &led->flash; > + struct led_classdev *lcdev = &flash->led_cdev; > + u32 sources[SY7802_MAX_LEDS]; > + int i, num, ret; > + > + num = of_property_count_u32_elems(np, "led-sources"); > + if (num < 1) { > + dev_err(dev, "Not specified or wrong number of led-sources\n"); > + return -EINVAL; > + } > + > + ret = of_property_read_u32_array(np, "led-sources", sources, num); > + if (ret) > + return ret; > + > + for (i = 0; i < num; i++) { > + if (sources[i] >= SY7802_MAX_LEDS) > + return -EINVAL; > + if (led->chip->leds_active & BIT(sources[i])) > + return -EINVAL; > + led->chip->leds_active |= BIT(sources[i]); > + } > + > + /* If both channels are specified in 'led-sources', joint flash output mode is used */ > + led->led_no = num == 2 ? SY7802_LED_JOINT : sources[0]; > + > + lcdev->max_brightness = SY7802_TORCH_BRIGHTNESS_MAX; > + lcdev->brightness_set_blocking = sy7802_torch_brightness_set; > + lcdev->flags |= LED_DEV_CAP_FLASH; > + > + flash->ops = &sy7802_flash_ops; > + > + sy7802_init_flash_brightness(flash); > + sy7802_init_flash_timeout(flash); > + > + return 0; > +} > + > +static int sy7802_chip_check(struct sy7802 *chip) > +{ > + struct device *dev = chip->dev; > + u32 chipid; > + int ret; > + > + ret = regmap_read(chip->regmap, SY7802_REG_DEV_ID, &chipid); > + if (ret) > + return dev_err_probe(dev, ret, "Failed to read chip ID\n"); > + > + if (chipid != SY7802_CHIP_ID) > + return dev_err_probe(dev, -ENODEV, "Chip reported wrong ID: %x\n", chipid); "Unsupported chip detected" > + > + return 0; > +} > + > +static void sy7802_enable(struct sy7802 *chip) > +{ > + gpiod_set_value_cansleep(chip->enable_gpio, 1); > + usleep_range(200, 300); > +} > + > +static void sy7802_disable(struct sy7802 *chip) > +{ > + gpiod_set_value_cansleep(chip->enable_gpio, 0); > +} > + > +static int sy7802_probe_dt(struct sy7802 *chip) > +{ > + struct device_node *np = dev_of_node(chip->dev), *child; This is ugly. Place 'child' on a separate line. > + int i = 0; If you're going to use a variable like this, rename it. 'count' or 'child_num' perhaps. And reset/assign it just before you're going to use it for clarity. > + int ret; > + > + regmap_write(chip->regmap, SY7802_REG_ENABLE, SY7802_MODE_OFF); > + regmap_write(chip->regmap, SY7802_REG_TORCH_BRIGHTNESS, LED_OFF); > + child_num = 0; > + for_each_available_child_of_node(np, child) { > + struct sy7802_led *led = chip->leds + i; > + > + led->chip = chip; > + led->led_no = i; > + > + ret = sy7802_init_flash_properties(chip->dev, led, child); > + if (ret) { > + of_node_put(child); > + return ret; > + } > + > + ret = sy7802_led_register(chip->dev, led, child); > + if (ret) { > + of_node_put(child); > + return ret; > + } > + > + i++; > + } > + return 0; > +} > + > +static const struct regmap_config sy7802_regmap_config = { > + .reg_bits = 8, > + .val_bits = 8, > + .max_register = 0xff, > + .cache_type = REGCACHE_MAPLE, > + .reg_defaults = sy7802_regmap_defs, > + .num_reg_defaults = ARRAY_SIZE(sy7802_regmap_defs), > +}; > + > +static int sy7802_probe(struct i2c_client *client) > +{ > + struct device *dev = &client->dev; > + struct sy7802 *chip; > + size_t count; > + int ret; > + > + count = device_get_child_node_count(dev); > + if (!count || count > SY7802_MAX_LEDS) > + return dev_err_probe(dev, -EINVAL, > + "No child node or node count over max led number %zu\n", count); Split them up and report on them individually or combine the error message: "Invalid amount of LED nodes" > + chip = devm_kzalloc(dev, struct_size(chip, leds, count), GFP_KERNEL); > + if (!chip) > + return -ENOMEM; > + > + chip->num_leds = count; > + > + chip->dev = dev; > + i2c_set_clientdata(client, chip); > + > + chip->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW); > + ret = PTR_ERR_OR_ZERO(chip->enable_gpio); > + if (ret) > + return dev_err_probe(dev, ret, "Failed to request enable gpio\n"); > + > + chip->vin_regulator = devm_regulator_get(dev, "vin"); > + ret = PTR_ERR_OR_ZERO(chip->vin_regulator); > + if (ret) > + return dev_err_probe(dev, ret, "Failed to request regulator\n"); > + > + ret = regulator_enable(chip->vin_regulator); > + if (ret) > + return dev_err_probe(dev, ret, "Failed to enable regulator\n"); > + > + chip->regmap = devm_regmap_init_i2c(client, &sy7802_regmap_config); > + if (IS_ERR(chip->regmap)) { > + regulator_disable(chip->vin_regulator); Nicer to use gotos for the error path. 3 calls to regulator_disable() is avoidable. > + return dev_err_probe(dev, PTR_ERR(chip->regmap), > + "Failed to allocate register map.\n"); > + } > + > + ret = sy7802_probe_dt(chip); > + if (ret < 0) { > + regulator_disable(chip->vin_regulator); > + return ret; > + } > + > + sy7802_enable(chip); > + > + ret = sy7802_chip_check(chip); > + if (ret) { > + sy7802_disable(chip); > + regulator_disable(chip->vin_regulator); > + return ret; > + } > + > + mutex_init(&chip->mutex); > + > + return ret; > +} > + > +static void sy7802_remove(struct i2c_client *client) > +{ > + struct sy7802 *chip = i2c_get_clientdata(client); > + > + sy7802_disable(chip); > + > + mutex_destroy(&chip->mutex); > + regulator_disable(chip->vin_regulator); > +} > + > +static const struct of_device_id __maybe_unused sy7802_leds_match[] = { > + { .compatible = "silergy,sy7802", }, > + {} > +}; > + > +MODULE_DEVICE_TABLE(of, sy7802_leds_match); > + > +static struct i2c_driver sy7802_driver = { > + .driver = { > + .name = "sy7802", > + .of_match_table = of_match_ptr(sy7802_leds_match), > + }, > + .probe = sy7802_probe, > + .remove = sy7802_remove, > +}; > + > +module_i2c_driver(sy7802_driver); > + > +MODULE_AUTHOR("André Apitzsch <git@apitzsch.eu>"); > +MODULE_DESCRIPTION("Silergy SY7802 flash LED driver"); > +MODULE_LICENSE("GPL"); > > -- > 2.44.0 > >
Hi Lee Jones, thanks for the feedback. I will address your comments in the next version. I have a few comments/questions though, see below. Best regards, André Am Donnerstag, dem 11.04.2024 um 13:48 +0100 schrieb Lee Jones: > On Mon, 01 Apr 2024, André Apitzsch via B4 Relay wrote: > > > > [..] > > + > > +#define SY7802_TIMEOUT_DEFAULT_US 512000U > > +#define SY7802_TIMEOUT_MIN_US 32000U > > +#define SY7802_TIMEOUT_MAX_US 1024000U > > +#define SY7802_TIMEOUT_STEPSIZE_US 32000U > > + > > +#define SY7802_TORCH_BRIGHTNESS_MAX 8 > > + > > +#define SY7802_FLASH_BRIGHTNESS_DEFAULT 14 > > +#define SY7802_FLASH_BRIGHTNESS_MIN 0 > > +#define SY7802_FLASH_BRIGHTNESS_MAX 15 > > +#define SY7802_FLASH_BRIGHTNESS_STEP 1 > > Much nicer to read if everything was aligned. Using tab size 8, SY7802_FLASH_BRIGHTNESS_* look aligned to me. Do you refer to SY7802_TORCH_BRIGHTNESS_MAX here? > > > [..] > > + > > + /* > > + * There is only one set of flash control logic, and this > > flag is used to check if 'strobe' > > The ',' before 'and' is superfluous. > > > + * is currently being used. > > + */ > > Doesn't the variable name kind of imply this? > > > + if (chip->fled_strobe_used) { > > + dev_warn(chip->dev, "Please disable strobe first > > [%d]\n", chip->fled_strobe_used); > > "Cannot set torch brightness whilst strobe is enabled" The comment and the warn message are taken from 'leds-mt6370-flash.c'. But I think using the warn message you suggested the comment can be removed. > > > + ret = -EBUSY; > > + goto unlock; > > + } > > + > > + if (level) > > + curr = chip->fled_torch_used | BIT(led->led_no); > > + else > > + curr = chip->fled_torch_used & ~BIT(led->led_no); > > + > > + if (curr) > > + val |= SY7802_MODE_TORCH; > > + > > + /* Torch needs to be disabled first to apply new > > brightness */ > > "Disable touch to apply brightness" > > > + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, > > SY7802_MODE_MASK, > > + SY7802_MODE_OFF); > > + if (ret) > > + goto unlock; > > + > > + mask = led->led_no == SY7802_LED_JOINT ? > > SY7802_TORCH_CURRENT_MASK_ALL : > > Why not just use led->led_no in place of mask? I might be missing something, but I don't know how to use led->led_no in place of mask, when led->led_no is in {0,1,2} and mask is in {0x07, 0x38, 0x3f}. > > Easier to read if you drop SY7802_TORCH_CURRENT_MASK_ALL to its own > line. > > > + SY7802_TORCH_CURRENT_MASK(led->led_no); > > + > > [..] > > + > > +static int sy7802_probe(struct i2c_client *client) > > +{ > > + struct device *dev = &client->dev; > > + struct sy7802 *chip; > > + size_t count; > > + int ret; > > + > > + count = device_get_child_node_count(dev); > > + if (!count || count > SY7802_MAX_LEDS) > > + return dev_err_probe(dev, -EINVAL, > > + "No child node or node count over max led > > number %zu\n", count); > > Split them up and report on them individually or combine the error > message: > > "Invalid amount of LED nodes" This snippet was also taken from 'leds-mt6370-flash.c'. >
On Wed, 01 May 2024, André Apitzsch wrote: > Hi Lee Jones, > > thanks for the feedback. I will address your comments in the next > version. I have a few comments/questions though, see below. > > Best regards, > André > > Am Donnerstag, dem 11.04.2024 um 13:48 +0100 schrieb Lee Jones: > > On Mon, 01 Apr 2024, André Apitzsch via B4 Relay wrote: > > > > > > [..] > > > + > > > +#define SY7802_TIMEOUT_DEFAULT_US 512000U > > > +#define SY7802_TIMEOUT_MIN_US 32000U > > > +#define SY7802_TIMEOUT_MAX_US 1024000U > > > +#define SY7802_TIMEOUT_STEPSIZE_US 32000U > > > + > > > +#define SY7802_TORCH_BRIGHTNESS_MAX 8 > > > + > > > +#define SY7802_FLASH_BRIGHTNESS_DEFAULT 14 > > > +#define SY7802_FLASH_BRIGHTNESS_MIN 0 > > > +#define SY7802_FLASH_BRIGHTNESS_MAX 15 > > > +#define SY7802_FLASH_BRIGHTNESS_STEP 1 > > > > Much nicer to read if everything was aligned. > > Using tab size 8, SY7802_FLASH_BRIGHTNESS_* look aligned to me. Do you > refer to SY7802_TORCH_BRIGHTNESS_MAX here? These were not aligned in my mailer. You can ignore. > > > [..] > > > + > > > + /* > > > + * There is only one set of flash control logic, and this > > > flag is used to check if 'strobe' > > > > The ',' before 'and' is superfluous. > > > > > + * is currently being used. > > > + */ > > > > Doesn't the variable name kind of imply this? > > > > > + if (chip->fled_strobe_used) { > > > + dev_warn(chip->dev, "Please disable strobe first > > > [%d]\n", chip->fled_strobe_used); > > > > "Cannot set torch brightness whilst strobe is enabled" > > The comment and the warn message are taken from 'leds-mt6370-flash.c'. > But I think using the warn message you suggested the comment can be > removed. It's an improvement, right? > > > + ret = -EBUSY; > > > + goto unlock; > > > + } > > > + > > > + if (level) > > > + curr = chip->fled_torch_used | BIT(led->led_no); > > > + else > > > + curr = chip->fled_torch_used & ~BIT(led->led_no); > > > + > > > + if (curr) > > > + val |= SY7802_MODE_TORCH; > > > + > > > + /* Torch needs to be disabled first to apply new > > > brightness */ > > > > "Disable touch to apply brightness" > > > > > + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, > > > SY7802_MODE_MASK, > > > + SY7802_MODE_OFF); > > > + if (ret) > > > + goto unlock; > > > + > > > + mask = led->led_no == SY7802_LED_JOINT ? > > > SY7802_TORCH_CURRENT_MASK_ALL : > > > > Why not just use led->led_no in place of mask? > > I might be missing something, but I don't know how to use led->led_no > in place of mask, when > led->led_no is in {0,1,2} and > mask is in {0x07, 0x38, 0x3f}. This doesn't make much sense. I guess you mean that led_no is a u8 and mask is a u32. What happens if you cast led_no to u32 in the call to regmap_update_bits()? > > Easier to read if you drop SY7802_TORCH_CURRENT_MASK_ALL to its own > > line. > > > > > + SY7802_TORCH_CURRENT_MASK(led->led_no); > > > + > > > [..] > > > + > > > +static int sy7802_probe(struct i2c_client *client) > > > +{ > > > + struct device *dev = &client->dev; > > > + struct sy7802 *chip; > > > + size_t count; > > > + int ret; > > > + > > > + count = device_get_child_node_count(dev); > > > + if (!count || count > SY7802_MAX_LEDS) > > > + return dev_err_probe(dev, -EINVAL, > > > + "No child node or node count over max led > > > number %zu\n", count); > > > > Split them up and report on them individually or combine the error > > message: > > > > "Invalid amount of LED nodes" > > This snippet was also taken from 'leds-mt6370-flash.c'. Old mistakes should not be repeated. :)
Am Donnerstag, dem 02.05.2024 um 10:10 +0100 schrieb Lee Jones: > On Wed, 01 May 2024, André Apitzsch wrote: > > > > > + ret = -EBUSY; > > > > + goto unlock; > > > > + } > > > > + > > > > + if (level) > > > > + curr = chip->fled_torch_used | BIT(led- > > > > >led_no); > > > > + else > > > > + curr = chip->fled_torch_used & ~BIT(led- > > > > >led_no); > > > > + > > > > + if (curr) > > > > + val |= SY7802_MODE_TORCH; > > > > + > > > > + /* Torch needs to be disabled first to apply new > > > > brightness */ > > > > > > "Disable touch to apply brightness" > > > > > > > + ret = regmap_update_bits(chip->regmap, > > > > SY7802_REG_ENABLE, > > > > SY7802_MODE_MASK, > > > > + SY7802_MODE_OFF); > > > > + if (ret) > > > > + goto unlock; > > > > + > > > > + mask = led->led_no == SY7802_LED_JOINT ? > > > > SY7802_TORCH_CURRENT_MASK_ALL : > > > > > > Why not just use led->led_no in place of mask? > > > > I might be missing something, but I don't know how to use led- > > >led_no > > in place of mask, when > > led->led_no is in {0,1,2} and > > mask is in {0x07, 0x38, 0x3f}. > > This doesn't make much sense. > > I guess you mean that led_no is a u8 and mask is a u32. > > What happens if you cast led_no to u32 in the call to > regmap_update_bits()? Sorry, I'm still confused. Could you elaborate your original question? > > > > Easier to read if you drop SY7802_TORCH_CURRENT_MASK_ALL to its > > > own > > > line. > > > > > > > + SY7802_TORCH_CURRENT_MASK(led->led_no); > > > > + > > > > [..] > > > > >
Le 01/04/2024 à 23:23, André Apitzsch via B4 Relay a écrit : > From: André Apitzsch <git@apitzsch.eu> > > Add support for SY7802 flash LED controller. It can support up to 1.8A > flash current. > > Signed-off-by: André Apitzsch <git@apitzsch.eu> > --- > drivers/leds/flash/Kconfig | 11 + > drivers/leds/flash/Makefile | 1 + > drivers/leds/flash/leds-sy7802.c | 532 +++++++++++++++++++++++++++++++++++++++ > 3 files changed, 544 insertions(+) ... > +static int sy7802_led_register(struct device *dev, struct sy7802_led *led, > + struct device_node *np) > +{ > + struct led_init_data init_data = {}; > + int ret; > + > + init_data.fwnode = of_fwnode_handle(np); > + > + ret = devm_led_classdev_flash_register_ext(dev, &led->flash, &init_data); > + if (ret) { > + dev_err(dev, "Couldn't register flash %d\n", led->led_no); > + return ret; > + } > + > + return ret; Hi, Nitpick: return 0; CJ > +}
On Thu, 11 Apr 2024, Lee Jones wrote: > On Mon, 01 Apr 2024, André Apitzsch via B4 Relay wrote: > > > From: André Apitzsch <git@apitzsch.eu> > > > > Add support for SY7802 flash LED controller. It can support up to 1.8A > > flash current. > > This is a very small commit message for a 500+ line change! > > Please, tell us more. > > > Signed-off-by: André Apitzsch <git@apitzsch.eu> > > --- > > drivers/leds/flash/Kconfig | 11 + > > drivers/leds/flash/Makefile | 1 + > > drivers/leds/flash/leds-sy7802.c | 532 +++++++++++++++++++++++++++++++++++++++ > > 3 files changed, 544 insertions(+) > > > > diff --git a/drivers/leds/flash/Kconfig b/drivers/leds/flash/Kconfig > > index 809b6d98bb3e..f39f0bfe6eef 100644 > > --- a/drivers/leds/flash/Kconfig > > +++ b/drivers/leds/flash/Kconfig > > @@ -121,4 +121,15 @@ config LEDS_SGM3140 > > This option enables support for the SGM3140 500mA Buck/Boost Charge > > Pump LED Driver. > > > > +config LEDS_SY7802 > > + tristate "LED support for the Silergy SY7802" > > + depends on I2C && OF > > + depends on GPIOLIB > > + select REGMAP_I2C > > + help > > + This option enables support for the SY7802 flash LED controller. > > + SY7802 includes torch and flash functions with programmable current. > > + > > + This driver can be built as a module, it will be called "leds-sy7802". > > + > > endif # LEDS_CLASS_FLASH > > diff --git a/drivers/leds/flash/Makefile b/drivers/leds/flash/Makefile > > index 91d60a4b7952..48860eeced79 100644 > > --- a/drivers/leds/flash/Makefile > > +++ b/drivers/leds/flash/Makefile > > @@ -11,3 +11,4 @@ obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom-flash.o > > obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o > > obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o > > obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o > > +obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o > > diff --git a/drivers/leds/flash/leds-sy7802.c b/drivers/leds/flash/leds-sy7802.c > > new file mode 100644 > > index 000000000000..c03a571b0e08 > > --- /dev/null > > +++ b/drivers/leds/flash/leds-sy7802.c > > @@ -0,0 +1,532 @@ [...] > > +static int sy7802_torch_brightness_set(struct led_classdev *lcdev, enum led_brightness level) > > s/level/brightness/ > > > +{ > > + struct sy7802_led *led = container_of(lcdev, struct sy7802_led, flash.led_cdev); > > + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? SY7802_LEDS_MASK_ALL : > > + SY7802_LEDS_MASK(led->led_no); > > Do all of the fancy multi-line assignment outside of the declaration block. > > > + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; > > + u32 val = level ? led_enable_mask : SY7802_MODE_OFF; > > + struct sy7802 *chip = led->chip; > > + u32 curr; > > This is a temporary placeholder for fled_torch_used, right? > > fled_torch_used_tmp? Sometimes abbreviated to tmp. > > > + u32 mask; > > That's a lot of masks. Which one is this? > > > + int ret; > > + > > + mutex_lock(&chip->mutex); > > + > > + /* > > + * There is only one set of flash control logic, and this flag is used to check if 'strobe' > > The ',' before 'and' is superfluous. > > > + * is currently being used. > > + */ > > Doesn't the variable name kind of imply this? > > > + if (chip->fled_strobe_used) { > > + dev_warn(chip->dev, "Please disable strobe first [%d]\n", chip->fled_strobe_used); > > "Cannot set torch brightness whilst strobe is enabled" > > > + ret = -EBUSY; > > + goto unlock; > > + } > > + > > + if (level) > > + curr = chip->fled_torch_used | BIT(led->led_no); > > + else > > + curr = chip->fled_torch_used & ~BIT(led->led_no); > > + > > + if (curr) > > + val |= SY7802_MODE_TORCH; > > + > > + /* Torch needs to be disabled first to apply new brightness */ > > "Disable touch to apply brightness" > > > + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, SY7802_MODE_MASK, > > + SY7802_MODE_OFF); > > + if (ret) > > + goto unlock; > > + > > + mask = led->led_no == SY7802_LED_JOINT ? SY7802_TORCH_CURRENT_MASK_ALL : > > Why not just use led->led_no in place of mask? mask and led->led_no are assigned the same value from this point on. > Easier to read if you drop SY7802_TORCH_CURRENT_MASK_ALL to its own line. > > > + SY7802_TORCH_CURRENT_MASK(led->led_no); > > + > > + /* Register expects brightness between 0 and MAX_BRIGHTNESS - 1 */ > > + if (level) > > + level -= 1; > > + > > + level |= (level << SY7802_TORCH_CURRENT_SHIFT); > > + > > + ret = regmap_update_bits(chip->regmap, SY7802_REG_TORCH_BRIGHTNESS, mask, level); So why not kill the single-use 'mask' variable and use a cast version of led->led_no here instead? > > + if (ret) > > + goto unlock; > > + > > + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, enable_mask, val); > > + if (ret) > > + goto unlock; > > + > > + chip->fled_torch_used = curr; > > + > > +unlock: > > + mutex_unlock(&chip->mutex); > > + return ret; > > +}
On Thu, 02 May 2024, André Apitzsch wrote: > Am Donnerstag, dem 02.05.2024 um 10:10 +0100 schrieb Lee Jones: > > On Wed, 01 May 2024, André Apitzsch wrote: > > > > > > > + ret = -EBUSY; > > > > > + goto unlock; > > > > > + } > > > > > + > > > > > + if (level) > > > > > + curr = chip->fled_torch_used | BIT(led- > > > > > >led_no); > > > > > + else > > > > > + curr = chip->fled_torch_used & ~BIT(led- > > > > > >led_no); > > > > > + > > > > > + if (curr) > > > > > + val |= SY7802_MODE_TORCH; > > > > > + > > > > > + /* Torch needs to be disabled first to apply new > > > > > brightness */ > > > > > > > > "Disable touch to apply brightness" > > > > > > > > > + ret = regmap_update_bits(chip->regmap, > > > > > SY7802_REG_ENABLE, > > > > > SY7802_MODE_MASK, > > > > > + SY7802_MODE_OFF); > > > > > + if (ret) > > > > > + goto unlock; > > > > > + > > > > > + mask = led->led_no == SY7802_LED_JOINT ? > > > > > SY7802_TORCH_CURRENT_MASK_ALL : > > > > > > > > Why not just use led->led_no in place of mask? > > > > > > I might be missing something, but I don't know how to use led- > > > >led_no > > > in place of mask, when > > > led->led_no is in {0,1,2} and > > > mask is in {0x07, 0x38, 0x3f}. > > > > This doesn't make much sense. > > > > I guess you mean that led_no is a u8 and mask is a u32. > > > > What happens if you cast led_no to u32 in the call to > > regmap_update_bits()? > > Sorry, I'm still confused. Could you elaborate your original question? Replied where there is still context.
Am Freitag, dem 03.05.2024 um 08:19 +0100 schrieb Lee Jones: > On Thu, 11 Apr 2024, Lee Jones wrote: > > > On Mon, 01 Apr 2024, André Apitzsch via B4 Relay wrote: > > > > > From: André Apitzsch <git@apitzsch.eu> > > > > > > Add support for SY7802 flash LED controller. It can support up to > > > 1.8A > > > flash current. > > > > This is a very small commit message for a 500+ line change! > > > > Please, tell us more. > > > > > Signed-off-by: André Apitzsch <git@apitzsch.eu> > > > --- > > > drivers/leds/flash/Kconfig | 11 + > > > drivers/leds/flash/Makefile | 1 + > > > drivers/leds/flash/leds-sy7802.c | 532 > > > +++++++++++++++++++++++++++++++++++++++ > > > 3 files changed, 544 insertions(+) > > > > > > diff --git a/drivers/leds/flash/Kconfig > > > b/drivers/leds/flash/Kconfig > > > index 809b6d98bb3e..f39f0bfe6eef 100644 > > > --- a/drivers/leds/flash/Kconfig > > > +++ b/drivers/leds/flash/Kconfig > > > @@ -121,4 +121,15 @@ config LEDS_SGM3140 > > > This option enables support for the SGM3140 500mA > > > Buck/Boost Charge > > > Pump LED Driver. > > > > > > +config LEDS_SY7802 > > > + tristate "LED support for the Silergy SY7802" > > > + depends on I2C && OF > > > + depends on GPIOLIB > > > + select REGMAP_I2C > > > + help > > > + This option enables support for the SY7802 flash LED > > > controller. > > > + SY7802 includes torch and flash functions with > > > programmable current. > > > + > > > + This driver can be built as a module, it will be > > > called "leds-sy7802". > > > + > > > endif # LEDS_CLASS_FLASH > > > diff --git a/drivers/leds/flash/Makefile > > > b/drivers/leds/flash/Makefile > > > index 91d60a4b7952..48860eeced79 100644 > > > --- a/drivers/leds/flash/Makefile > > > +++ b/drivers/leds/flash/Makefile > > > @@ -11,3 +11,4 @@ obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom- > > > flash.o > > > obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o > > > obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o > > > obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o > > > +obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o > > > diff --git a/drivers/leds/flash/leds-sy7802.c > > > b/drivers/leds/flash/leds-sy7802.c > > > new file mode 100644 > > > index 000000000000..c03a571b0e08 > > > --- /dev/null > > > +++ b/drivers/leds/flash/leds-sy7802.c > > > @@ -0,0 +1,532 @@ > > [...] > > > > +static int sy7802_torch_brightness_set(struct led_classdev > > > *lcdev, enum led_brightness level) > > > > s/level/brightness/ > > > > > +{ > > > + struct sy7802_led *led = container_of(lcdev, struct > > > sy7802_led, flash.led_cdev); > > > + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? > > > SY7802_LEDS_MASK_ALL : > > > + SY7802_LEDS_MASK(led->led_no); > > > > Do all of the fancy multi-line assignment outside of the > > declaration block. > > > > > + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; > > > + u32 val = level ? led_enable_mask : SY7802_MODE_OFF; > > > + struct sy7802 *chip = led->chip; > > > + u32 curr; > > > > This is a temporary placeholder for fled_torch_used, right? > > > > fled_torch_used_tmp? Sometimes abbreviated to tmp. > > > > > + u32 mask; > > > > That's a lot of masks. Which one is this? > > > > > + int ret; > > > + > > > + mutex_lock(&chip->mutex); > > > + > > > + /* > > > + * There is only one set of flash control logic, and > > > this flag is used to check if 'strobe' > > > > The ',' before 'and' is superfluous. > > > > > + * is currently being used. > > > + */ > > > > Doesn't the variable name kind of imply this? > > > > > + if (chip->fled_strobe_used) { > > > + dev_warn(chip->dev, "Please disable strobe first > > > [%d]\n", chip->fled_strobe_used); > > > > "Cannot set torch brightness whilst strobe is enabled" > > > > > + ret = -EBUSY; > > > + goto unlock; > > > + } > > > + > > > + if (level) > > > + curr = chip->fled_torch_used | BIT(led->led_no); > > > + else > > > + curr = chip->fled_torch_used & ~BIT(led- > > > >led_no); > > > + > > > + if (curr) > > > + val |= SY7802_MODE_TORCH; > > > + > > > + /* Torch needs to be disabled first to apply new > > > brightness */ > > > > "Disable touch to apply brightness" > > > > > + ret = regmap_update_bits(chip->regmap, > > > SY7802_REG_ENABLE, SY7802_MODE_MASK, > > > + SY7802_MODE_OFF); > > > + if (ret) > > > + goto unlock; > > > + > > > + mask = led->led_no == SY7802_LED_JOINT ? > > > SY7802_TORCH_CURRENT_MASK_ALL : > > > > Why not just use led->led_no in place of mask? > > mask and led->led_no are assigned the same value from this point on. Thanks for the clarification. How to you come to the conclusion that mask and led->led_no are assigned the same value from this point on? The value of led->led_no is used here only as part of the if condition (led->led_no == SY7802_LED_JOINT) and not assigned to mask. > > > Easier to read if you drop SY7802_TORCH_CURRENT_MASK_ALL to its own > > line. > > > > > + SY7802_TORCH_CURRENT_MASK(led->led_no); > > > + > > > + /* Register expects brightness between 0 and > > > MAX_BRIGHTNESS - 1 */ > > > + if (level) > > > + level -= 1; > > > + > > > + level |= (level << SY7802_TORCH_CURRENT_SHIFT); > > > + > > > + ret = regmap_update_bits(chip->regmap, > > > SY7802_REG_TORCH_BRIGHTNESS, mask, level); > > So why not kill the single-use 'mask' variable and use a cast version > of led->led_no here instead? > > > > + if (ret) > > > + goto unlock; > > > + > > > + ret = regmap_update_bits(chip->regmap, > > > SY7802_REG_ENABLE, enable_mask, val); > > > + if (ret) > > > + goto unlock; > > > + > > > + chip->fled_torch_used = curr; > > > + > > > +unlock: > > > + mutex_unlock(&chip->mutex); > > > + return ret; > > > +} >
On Sat, 04 May 2024, André Apitzsch wrote: > Am Freitag, dem 03.05.2024 um 08:19 +0100 schrieb Lee Jones: > > On Thu, 11 Apr 2024, Lee Jones wrote: > > > > > On Mon, 01 Apr 2024, André Apitzsch via B4 Relay wrote: > > > > > > > From: André Apitzsch <git@apitzsch.eu> > > > > > > > > Add support for SY7802 flash LED controller. It can support up to > > > > 1.8A > > > > flash current. > > > > > > This is a very small commit message for a 500+ line change! > > > > > > Please, tell us more. > > > > > > > Signed-off-by: André Apitzsch <git@apitzsch.eu> > > > > --- > > > > drivers/leds/flash/Kconfig | 11 + > > > > drivers/leds/flash/Makefile | 1 + > > > > drivers/leds/flash/leds-sy7802.c | 532 > > > > +++++++++++++++++++++++++++++++++++++++ > > > > 3 files changed, 544 insertions(+) > > > > > > > > diff --git a/drivers/leds/flash/Kconfig > > > > b/drivers/leds/flash/Kconfig > > > > index 809b6d98bb3e..f39f0bfe6eef 100644 > > > > --- a/drivers/leds/flash/Kconfig > > > > +++ b/drivers/leds/flash/Kconfig > > > > @@ -121,4 +121,15 @@ config LEDS_SGM3140 > > > > This option enables support for the SGM3140 500mA > > > > Buck/Boost Charge > > > > Pump LED Driver. > > > > > > > > +config LEDS_SY7802 > > > > + tristate "LED support for the Silergy SY7802" > > > > + depends on I2C && OF > > > > + depends on GPIOLIB > > > > + select REGMAP_I2C > > > > + help > > > > + This option enables support for the SY7802 flash LED > > > > controller. > > > > + SY7802 includes torch and flash functions with > > > > programmable current. > > > > + > > > > + This driver can be built as a module, it will be > > > > called "leds-sy7802". > > > > + > > > > endif # LEDS_CLASS_FLASH > > > > diff --git a/drivers/leds/flash/Makefile > > > > b/drivers/leds/flash/Makefile > > > > index 91d60a4b7952..48860eeced79 100644 > > > > --- a/drivers/leds/flash/Makefile > > > > +++ b/drivers/leds/flash/Makefile > > > > @@ -11,3 +11,4 @@ obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom- > > > > flash.o > > > > obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o > > > > obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o > > > > obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o > > > > +obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o > > > > diff --git a/drivers/leds/flash/leds-sy7802.c > > > > b/drivers/leds/flash/leds-sy7802.c > > > > new file mode 100644 > > > > index 000000000000..c03a571b0e08 > > > > --- /dev/null > > > > +++ b/drivers/leds/flash/leds-sy7802.c > > > > @@ -0,0 +1,532 @@ > > > > [...] > > > > > > +static int sy7802_torch_brightness_set(struct led_classdev > > > > *lcdev, enum led_brightness level) > > > > > > s/level/brightness/ > > > > > > > +{ > > > > + struct sy7802_led *led = container_of(lcdev, struct > > > > sy7802_led, flash.led_cdev); > > > > + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? > > > > SY7802_LEDS_MASK_ALL : > > > > + SY7802_LEDS_MASK(led->led_no); > > > > > > Do all of the fancy multi-line assignment outside of the > > > declaration block. > > > > > > > + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; > > > > + u32 val = level ? led_enable_mask : SY7802_MODE_OFF; > > > > + struct sy7802 *chip = led->chip; > > > > + u32 curr; > > > > > > This is a temporary placeholder for fled_torch_used, right? > > > > > > fled_torch_used_tmp? Sometimes abbreviated to tmp. > > > > > > > + u32 mask; > > > > > > That's a lot of masks. Which one is this? > > > > > > > + int ret; > > > > + > > > > + mutex_lock(&chip->mutex); > > > > + > > > > + /* > > > > + * There is only one set of flash control logic, and > > > > this flag is used to check if 'strobe' > > > > > > The ',' before 'and' is superfluous. > > > > > > > + * is currently being used. > > > > + */ > > > > > > Doesn't the variable name kind of imply this? > > > > > > > + if (chip->fled_strobe_used) { > > > > + dev_warn(chip->dev, "Please disable strobe first > > > > [%d]\n", chip->fled_strobe_used); > > > > > > "Cannot set torch brightness whilst strobe is enabled" > > > > > > > + ret = -EBUSY; > > > > + goto unlock; > > > > + } > > > > + > > > > + if (level) > > > > + curr = chip->fled_torch_used | BIT(led->led_no); > > > > + else > > > > + curr = chip->fled_torch_used & ~BIT(led- > > > > >led_no); > > > > + > > > > + if (curr) > > > > + val |= SY7802_MODE_TORCH; > > > > + > > > > + /* Torch needs to be disabled first to apply new > > > > brightness */ > > > > > > "Disable touch to apply brightness" > > > > > > > + ret = regmap_update_bits(chip->regmap, > > > > SY7802_REG_ENABLE, SY7802_MODE_MASK, > > > > + SY7802_MODE_OFF); > > > > + if (ret) > > > > + goto unlock; > > > > + > > > > + mask = led->led_no == SY7802_LED_JOINT ? > > > > SY7802_TORCH_CURRENT_MASK_ALL : > > > > > > Why not just use led->led_no in place of mask? > > > > mask and led->led_no are assigned the same value from this point on. > > Thanks for the clarification. > How to you come to the conclusion that mask and led->led_no are > assigned the same value from this point on? Because I am blind and didn't see the double equals ("=="). #shouldhavegonetospecsavers
diff --git a/drivers/leds/flash/Kconfig b/drivers/leds/flash/Kconfig index 809b6d98bb3e..f39f0bfe6eef 100644 --- a/drivers/leds/flash/Kconfig +++ b/drivers/leds/flash/Kconfig @@ -121,4 +121,15 @@ config LEDS_SGM3140 This option enables support for the SGM3140 500mA Buck/Boost Charge Pump LED Driver. +config LEDS_SY7802 + tristate "LED support for the Silergy SY7802" + depends on I2C && OF + depends on GPIOLIB + select REGMAP_I2C + help + This option enables support for the SY7802 flash LED controller. + SY7802 includes torch and flash functions with programmable current. + + This driver can be built as a module, it will be called "leds-sy7802". + endif # LEDS_CLASS_FLASH diff --git a/drivers/leds/flash/Makefile b/drivers/leds/flash/Makefile index 91d60a4b7952..48860eeced79 100644 --- a/drivers/leds/flash/Makefile +++ b/drivers/leds/flash/Makefile @@ -11,3 +11,4 @@ obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom-flash.o obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o +obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o diff --git a/drivers/leds/flash/leds-sy7802.c b/drivers/leds/flash/leds-sy7802.c new file mode 100644 index 000000000000..c03a571b0e08 --- /dev/null +++ b/drivers/leds/flash/leds-sy7802.c @@ -0,0 +1,532 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Silergy SY7802 flash LED driver with I2C interface + * + * Copyright 2024 André Apitzsch <git@apitzsch.eu> + */ + +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/led-class-flash.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> + +#define SY7802_MAX_LEDS 2 +#define SY7802_LED_JOINT 2 + +#define SY7802_REG_ENABLE 0x10 +#define SY7802_REG_TORCH_BRIGHTNESS 0xa0 +#define SY7802_REG_FLASH_BRIGHTNESS 0xb0 +#define SY7802_REG_FLASH_DURATION 0xc0 +#define SY7802_REG_FLAGS 0xd0 +#define SY7802_REG_CONFIG_1 0xe0 +#define SY7802_REG_CONFIG_2 0xf0 +#define SY7802_REG_VIN_MONITOR 0x80 +#define SY7802_REG_LAST_FLASH 0x81 +#define SY7802_REG_VLED_MONITOR 0x30 +#define SY7802_REG_ADC_DELAY 0x31 +#define SY7802_REG_DEV_ID 0xff + +#define SY7802_MODE_OFF 0 +#define SY7802_MODE_TORCH 2 +#define SY7802_MODE_FLASH 3 +#define SY7802_MODE_MASK GENMASK(1, 0) + +#define SY7802_LEDS_SHIFT 3 +#define SY7802_LEDS_MASK(_id) (BIT(_id) << SY7802_LEDS_SHIFT) +#define SY7802_LEDS_MASK_ALL (SY7802_LEDS_MASK(0) | SY7802_LEDS_MASK(1)) + +#define SY7802_TORCH_CURRENT_SHIFT 3 +#define SY7802_TORCH_CURRENT_MASK(_id) \ + (GENMASK(2, 0) << (SY7802_TORCH_CURRENT_SHIFT * (_id))) +#define SY7802_TORCH_CURRENT_MASK_ALL \ + (SY7802_TORCH_CURRENT_MASK(0) | SY7802_TORCH_CURRENT_MASK(1)) + +#define SY7802_FLASH_CURRENT_SHIFT 4 +#define SY7802_FLASH_CURRENT_MASK(_id) \ + (GENMASK(3, 0) << (SY7802_FLASH_CURRENT_SHIFT * (_id))) +#define SY7802_FLASH_CURRENT_MASK_ALL \ + (SY7802_FLASH_CURRENT_MASK(0) | SY7802_FLASH_CURRENT_MASK(1)) + +#define SY7802_TIMEOUT_DEFAULT_US 512000U +#define SY7802_TIMEOUT_MIN_US 32000U +#define SY7802_TIMEOUT_MAX_US 1024000U +#define SY7802_TIMEOUT_STEPSIZE_US 32000U + +#define SY7802_TORCH_BRIGHTNESS_MAX 8 + +#define SY7802_FLASH_BRIGHTNESS_DEFAULT 14 +#define SY7802_FLASH_BRIGHTNESS_MIN 0 +#define SY7802_FLASH_BRIGHTNESS_MAX 15 +#define SY7802_FLASH_BRIGHTNESS_STEP 1 + +#define SY7802_FLAG_TIMEOUT (1 << 0) +#define SY7802_FLAG_THERMAL_SHUTDOWN (1 << 1) +#define SY7802_FLAG_LED_FAULT (1 << 2) +#define SY7802_FLAG_TX1_INTERRUPT (1 << 3) +#define SY7802_FLAG_TX2_INTERRUPT (1 << 4) +#define SY7802_FLAG_LED_THERMAL_FAULT (1 << 5) +#define SY7802_FLAG_FLASH_INPUT_VOLTAGE_LOW (1 << 6) +#define SY7802_FLAG_INPUT_VOLTAGE_LOW (1 << 7) + +#define SY7802_CHIP_ID 0x51 + +static const struct reg_default sy7802_regmap_defs[] = { + { SY7802_REG_ENABLE, SY7802_LEDS_MASK_ALL }, + { SY7802_REG_TORCH_BRIGHTNESS, 0x92 }, + { SY7802_REG_FLASH_BRIGHTNESS, SY7802_FLASH_BRIGHTNESS_DEFAULT | + SY7802_FLASH_BRIGHTNESS_DEFAULT << SY7802_FLASH_CURRENT_SHIFT }, + { SY7802_REG_FLASH_DURATION, 0x6f }, + { SY7802_REG_FLAGS, 0x0 }, + { SY7802_REG_CONFIG_1, 0x68 }, + { SY7802_REG_CONFIG_2, 0xf0 }, +}; + +struct sy7802_led { + struct led_classdev_flash flash; + struct sy7802 *chip; + u8 led_no; +}; + +struct sy7802 { + struct mutex mutex; + struct device *dev; + struct regmap *regmap; + + struct gpio_desc *enable_gpio; + struct regulator *vin_regulator; + + unsigned int fled_strobe_used; + unsigned int fled_torch_used; + unsigned int leds_active; + int num_leds; + struct sy7802_led leds[] __counted_by(num_leds); +}; + +static int sy7802_torch_brightness_set(struct led_classdev *lcdev, enum led_brightness level) +{ + struct sy7802_led *led = container_of(lcdev, struct sy7802_led, flash.led_cdev); + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? SY7802_LEDS_MASK_ALL : + SY7802_LEDS_MASK(led->led_no); + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; + u32 val = level ? led_enable_mask : SY7802_MODE_OFF; + struct sy7802 *chip = led->chip; + u32 curr; + u32 mask; + int ret; + + mutex_lock(&chip->mutex); + + /* + * There is only one set of flash control logic, and this flag is used to check if 'strobe' + * is currently being used. + */ + if (chip->fled_strobe_used) { + dev_warn(chip->dev, "Please disable strobe first [%d]\n", chip->fled_strobe_used); + ret = -EBUSY; + goto unlock; + } + + if (level) + curr = chip->fled_torch_used | BIT(led->led_no); + else + curr = chip->fled_torch_used & ~BIT(led->led_no); + + if (curr) + val |= SY7802_MODE_TORCH; + + /* Torch needs to be disabled first to apply new brightness */ + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, SY7802_MODE_MASK, + SY7802_MODE_OFF); + if (ret) + goto unlock; + + mask = led->led_no == SY7802_LED_JOINT ? SY7802_TORCH_CURRENT_MASK_ALL : + SY7802_TORCH_CURRENT_MASK(led->led_no); + + /* Register expects brightness between 0 and MAX_BRIGHTNESS - 1 */ + if (level) + level -= 1; + + level |= (level << SY7802_TORCH_CURRENT_SHIFT); + + ret = regmap_update_bits(chip->regmap, SY7802_REG_TORCH_BRIGHTNESS, mask, level); + if (ret) + goto unlock; + + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, enable_mask, val); + if (ret) + goto unlock; + + chip->fled_torch_used = curr; + +unlock: + mutex_unlock(&chip->mutex); + return ret; +} + +static int sy7802_flash_brightness_set(struct led_classdev_flash *fl_cdev, u32 brightness) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + struct led_flash_setting *s = &fl_cdev->brightness; + u32 val = (brightness - s->min) / s->step; + struct sy7802 *chip = led->chip; + u32 mask; + int ret; + + val |= (val << SY7802_FLASH_CURRENT_SHIFT); + mask = led->led_no == SY7802_LED_JOINT ? SY7802_FLASH_CURRENT_MASK_ALL : + SY7802_FLASH_CURRENT_MASK(led->led_no); + + mutex_lock(&chip->mutex); + ret = regmap_update_bits(chip->regmap, SY7802_REG_FLASH_BRIGHTNESS, mask, val); + mutex_unlock(&chip->mutex); + + return ret; +} + +static int sy7802_strobe_set(struct led_classdev_flash *fl_cdev, bool state) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ? SY7802_LEDS_MASK_ALL : + SY7802_LEDS_MASK(led->led_no); + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask; + u32 val = state ? led_enable_mask : SY7802_MODE_OFF; + struct sy7802 *chip = led->chip; + u32 curr; + int ret; + + mutex_lock(&chip->mutex); + + /* + * There is only one set of flash control logic, and this flag is used to check if 'torch' + * is currently being used. + */ + if (chip->fled_torch_used) { + dev_warn(chip->dev, "Please disable torch first [0x%x]\n", chip->fled_torch_used); + ret = -EBUSY; + goto unlock; + } + + if (state) + curr = chip->fled_strobe_used | BIT(led->led_no); + else + curr = chip->fled_strobe_used & ~BIT(led->led_no); + + if (curr) + val |= SY7802_MODE_FLASH; + + ret = regmap_update_bits(chip->regmap, SY7802_REG_ENABLE, enable_mask, val); + + if (ret) + goto unlock; + + chip->fled_strobe_used = curr; + +unlock: + mutex_unlock(&chip->mutex); + return ret; +} + +static int sy7802_strobe_get(struct led_classdev_flash *fl_cdev, bool *state) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + struct sy7802 *chip = led->chip; + + mutex_lock(&chip->mutex); + *state = !!(chip->fled_strobe_used & BIT(led->led_no)); + mutex_unlock(&chip->mutex); + + return 0; +} + +static int sy7802_timeout_set(struct led_classdev_flash *fl_cdev, + u32 timeout) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + struct led_flash_setting *s = &fl_cdev->timeout; + u32 val = (timeout - s->min) / s->step; + struct sy7802 *chip = led->chip; + + return regmap_write(chip->regmap, SY7802_REG_FLASH_DURATION, val); +} + +static int sy7802_fault_get(struct led_classdev_flash *fl_cdev, u32 *fault) +{ + struct sy7802_led *led = container_of(fl_cdev, struct sy7802_led, flash); + struct sy7802 *chip = led->chip; + u32 val, led_faults = 0; + int ret; + + /* NOTE: reading register clears fault status */ + ret = regmap_read(chip->regmap, SY7802_REG_FLAGS, &val); + if (ret) + return ret; + + if (val & (SY7802_FLAG_FLASH_INPUT_VOLTAGE_LOW | SY7802_FLAG_INPUT_VOLTAGE_LOW)) + led_faults |= LED_FAULT_INPUT_VOLTAGE; + + if (val & SY7802_FLAG_THERMAL_SHUTDOWN) + led_faults |= LED_FAULT_OVER_TEMPERATURE; + + if (val & SY7802_FLAG_TIMEOUT) + led_faults |= LED_FAULT_TIMEOUT; + + *fault = led_faults; + return 0; +} + +static const struct led_flash_ops sy7802_flash_ops = { + .flash_brightness_set = sy7802_flash_brightness_set, + .strobe_set = sy7802_strobe_set, + .strobe_get = sy7802_strobe_get, + .timeout_set = sy7802_timeout_set, + .fault_get = sy7802_fault_get, +}; + +static void sy7802_init_flash_brightness(struct led_classdev_flash *fl_cdev) +{ + struct led_flash_setting *s; + + /* Init flash brightness setting */ + s = &fl_cdev->brightness; + s->min = SY7802_FLASH_BRIGHTNESS_MIN; + s->max = SY7802_FLASH_BRIGHTNESS_MAX; + s->step = SY7802_FLASH_BRIGHTNESS_STEP; + s->val = SY7802_FLASH_BRIGHTNESS_DEFAULT; +} + +static void sy7802_init_flash_timeout(struct led_classdev_flash *fl_cdev) +{ + struct led_flash_setting *s; + + /* Init flash timeout setting */ + s = &fl_cdev->timeout; + s->min = SY7802_TIMEOUT_MIN_US; + s->max = SY7802_TIMEOUT_MAX_US; + s->step = SY7802_TIMEOUT_STEPSIZE_US; + s->val = SY7802_TIMEOUT_DEFAULT_US; +} + +static int sy7802_led_register(struct device *dev, struct sy7802_led *led, + struct device_node *np) +{ + struct led_init_data init_data = {}; + int ret; + + init_data.fwnode = of_fwnode_handle(np); + + ret = devm_led_classdev_flash_register_ext(dev, &led->flash, &init_data); + if (ret) { + dev_err(dev, "Couldn't register flash %d\n", led->led_no); + return ret; + } + + return ret; +} + +static int sy7802_init_flash_properties(struct device *dev, struct sy7802_led *led, + struct device_node *np) +{ + struct led_classdev_flash *flash = &led->flash; + struct led_classdev *lcdev = &flash->led_cdev; + u32 sources[SY7802_MAX_LEDS]; + int i, num, ret; + + num = of_property_count_u32_elems(np, "led-sources"); + if (num < 1) { + dev_err(dev, "Not specified or wrong number of led-sources\n"); + return -EINVAL; + } + + ret = of_property_read_u32_array(np, "led-sources", sources, num); + if (ret) + return ret; + + for (i = 0; i < num; i++) { + if (sources[i] >= SY7802_MAX_LEDS) + return -EINVAL; + if (led->chip->leds_active & BIT(sources[i])) + return -EINVAL; + led->chip->leds_active |= BIT(sources[i]); + } + + /* If both channels are specified in 'led-sources', joint flash output mode is used */ + led->led_no = num == 2 ? SY7802_LED_JOINT : sources[0]; + + lcdev->max_brightness = SY7802_TORCH_BRIGHTNESS_MAX; + lcdev->brightness_set_blocking = sy7802_torch_brightness_set; + lcdev->flags |= LED_DEV_CAP_FLASH; + + flash->ops = &sy7802_flash_ops; + + sy7802_init_flash_brightness(flash); + sy7802_init_flash_timeout(flash); + + return 0; +} + +static int sy7802_chip_check(struct sy7802 *chip) +{ + struct device *dev = chip->dev; + u32 chipid; + int ret; + + ret = regmap_read(chip->regmap, SY7802_REG_DEV_ID, &chipid); + if (ret) + return dev_err_probe(dev, ret, "Failed to read chip ID\n"); + + if (chipid != SY7802_CHIP_ID) + return dev_err_probe(dev, -ENODEV, "Chip reported wrong ID: %x\n", chipid); + + return 0; +} + +static void sy7802_enable(struct sy7802 *chip) +{ + gpiod_set_value_cansleep(chip->enable_gpio, 1); + usleep_range(200, 300); +} + +static void sy7802_disable(struct sy7802 *chip) +{ + gpiod_set_value_cansleep(chip->enable_gpio, 0); +} + +static int sy7802_probe_dt(struct sy7802 *chip) +{ + struct device_node *np = dev_of_node(chip->dev), *child; + int i = 0; + int ret; + + regmap_write(chip->regmap, SY7802_REG_ENABLE, SY7802_MODE_OFF); + regmap_write(chip->regmap, SY7802_REG_TORCH_BRIGHTNESS, LED_OFF); + + for_each_available_child_of_node(np, child) { + struct sy7802_led *led = chip->leds + i; + + led->chip = chip; + led->led_no = i; + + ret = sy7802_init_flash_properties(chip->dev, led, child); + if (ret) { + of_node_put(child); + return ret; + } + + ret = sy7802_led_register(chip->dev, led, child); + if (ret) { + of_node_put(child); + return ret; + } + + i++; + } + return 0; +} + +static const struct regmap_config sy7802_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = 0xff, + .cache_type = REGCACHE_MAPLE, + .reg_defaults = sy7802_regmap_defs, + .num_reg_defaults = ARRAY_SIZE(sy7802_regmap_defs), +}; + +static int sy7802_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct sy7802 *chip; + size_t count; + int ret; + + count = device_get_child_node_count(dev); + if (!count || count > SY7802_MAX_LEDS) + return dev_err_probe(dev, -EINVAL, + "No child node or node count over max led number %zu\n", count); + + chip = devm_kzalloc(dev, struct_size(chip, leds, count), GFP_KERNEL); + if (!chip) + return -ENOMEM; + + chip->num_leds = count; + + chip->dev = dev; + i2c_set_clientdata(client, chip); + + chip->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW); + ret = PTR_ERR_OR_ZERO(chip->enable_gpio); + if (ret) + return dev_err_probe(dev, ret, "Failed to request enable gpio\n"); + + chip->vin_regulator = devm_regulator_get(dev, "vin"); + ret = PTR_ERR_OR_ZERO(chip->vin_regulator); + if (ret) + return dev_err_probe(dev, ret, "Failed to request regulator\n"); + + ret = regulator_enable(chip->vin_regulator); + if (ret) + return dev_err_probe(dev, ret, "Failed to enable regulator\n"); + + chip->regmap = devm_regmap_init_i2c(client, &sy7802_regmap_config); + if (IS_ERR(chip->regmap)) { + regulator_disable(chip->vin_regulator); + return dev_err_probe(dev, PTR_ERR(chip->regmap), + "Failed to allocate register map.\n"); + } + + ret = sy7802_probe_dt(chip); + if (ret < 0) { + regulator_disable(chip->vin_regulator); + return ret; + } + + sy7802_enable(chip); + + ret = sy7802_chip_check(chip); + if (ret) { + sy7802_disable(chip); + regulator_disable(chip->vin_regulator); + return ret; + } + + mutex_init(&chip->mutex); + + return ret; +} + +static void sy7802_remove(struct i2c_client *client) +{ + struct sy7802 *chip = i2c_get_clientdata(client); + + sy7802_disable(chip); + + mutex_destroy(&chip->mutex); + regulator_disable(chip->vin_regulator); +} + +static const struct of_device_id __maybe_unused sy7802_leds_match[] = { + { .compatible = "silergy,sy7802", }, + {} +}; + +MODULE_DEVICE_TABLE(of, sy7802_leds_match); + +static struct i2c_driver sy7802_driver = { + .driver = { + .name = "sy7802", + .of_match_table = of_match_ptr(sy7802_leds_match), + }, + .probe = sy7802_probe, + .remove = sy7802_remove, +}; + +module_i2c_driver(sy7802_driver); + +MODULE_AUTHOR("André Apitzsch <git@apitzsch.eu>"); +MODULE_DESCRIPTION("Silergy SY7802 flash LED driver"); +MODULE_LICENSE("GPL");