@@ -8,6 +8,7 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "ipq9574-rdp-common.dtsi"
/ {
@@ -15,6 +16,45 @@ / {
compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
};
+&pcie1_phy {
+ status = "okay";
+};
+
+&pcie1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_default>;
+
+ perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pcie2_phy {
+ status = "okay";
+};
+
+&pcie2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_default>;
+
+ perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pcie3_phy {
+ status = "okay";
+};
+
+&pcie3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie3_default>;
+
+ perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
&sdhc_1 {
pinctrl-0 = <&sdc_default_state>;
pinctrl-names = "default";
@@ -28,6 +68,79 @@ &sdhc_1 {
};
&tlmm {
+
+ pcie1_default: pcie1-default-state {
+ clkreq-n-pins {
+ pins = "gpio25";
+ function = "pcie1_clk";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio26";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ output-low;
+ };
+
+ wake-n-pins {
+ pins = "gpio27";
+ function = "pcie1_wake";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ pcie2_default: pcie2-default-state {
+ clkreq-n-pins {
+ pins = "gpio28";
+ function = "pcie2_clk";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio29";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ output-low;
+ };
+
+ wake-n-pins {
+ pins = "gpio30";
+ function = "pcie2_wake";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ pcie3_default: pcie3-default-state {
+ clkreq-n-pins {
+ pins = "gpio31";
+ function = "pcie3_clk";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio32";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ output-low;
+ };
+
+ wake-n-pins {
+ pins = "gpio33";
+ function = "pcie3_wake";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
sdc_default_state: sdc-default-state {
clk-pins {
pins = "gpio5";
Enable the PCIe controller and PHY nodes corresponding to RDP 433. Signed-off-by: devi priya <quic_devipriy@quicinc.com> --- Changes in V5: - No change arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 113 ++++++++++++++++++++ 1 file changed, 113 insertions(+)