diff mbox series

ARM: dts: qcom: msm8926-motorola-peregrine: Add accelerometer, magnetometer, regulator

Message ID 20240616-peregrine-v1-1-85d14ae1a11a@apitzsch.eu (mailing list archive)
State Changes Requested
Headers show
Series ARM: dts: qcom: msm8926-motorola-peregrine: Add accelerometer, magnetometer, regulator | expand

Commit Message

André Apitzsch via B4 Relay June 16, 2024, 2:15 p.m. UTC 
From: André Apitzsch <git@apitzsch.eu>

Add the accelerometer, magnetometer and regulator that are present on
the Motorola Moto G 4G (2013) device.

While at it, update framebuffer supplies and temperature sensor.

Signed-off-by: André Apitzsch <git@apitzsch.eu>
---
 .../dts/qcom/qcom-msm8926-motorola-peregrine.dts   | 121 +++++++++++++++++++++
 1 file changed, 121 insertions(+)


---
base-commit: c71189547381bb5f176c6b22a9edc3414f1837b9
change-id: 20240616-peregrine-6ec5e26b15ec

Best regards,

Comments

Konrad Dybcio June 17, 2024, 7:58 p.m. UTC | #1 
On 6/16/24 16:15, André Apitzsch via B4 Relay wrote:
> From: André Apitzsch <git@apitzsch.eu>
> 
> Add the accelerometer, magnetometer and regulator that are present on
> the Motorola Moto G 4G (2013) device.
> 
> While at it, update framebuffer supplies and temperature sensor.

That's a bit too much for a "while at it" ;) Please create separate commits

[...]

>   	sensor@48 {
>   		compatible = "ti,tmp108";
>   		reg = <0x48>;
> +		interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-0 = <&temp_alert_default>;
> +		pinctrl-names = "default";
> +		#thermal-sensor-cells = <0>;

FWIW the current driver doesn't seem to care about interrupts, perhaps
you could extend it


Konrad
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
index 0cbe2d2fbbb1..376a33125941 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
@@ -29,6 +29,10 @@  framebuffer0: framebuffer@3200000 {
 			height = <1280>;
 			stride = <(720 * 3)>;
 			format = "r8g8b8";
+			vsp-supply = <&reg_lcd_pos>;
+			vsn-supply = <&reg_lcd_neg>;
+			vdd-supply = <&pm8226_l28>;
+			vddio-supply = <&vddio_disp_vreg>;
 		};
 	};
 
@@ -51,6 +55,18 @@  key-volume-up {
 		};
 	};
 
+	vddio_disp_vreg: regulator-vddio-disp {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio_disp";
+		gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <300>;
+		enable-active-high;
+		regulator-boot-on;
+		vin-supply = <&pm8226_l8>;
+		pinctrl-0 = <&disp_vddio_default>;
+		pinctrl-names = "default";
+	};
+
 	reserved-memory {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -68,12 +84,67 @@  smem_region: smem@fa00000 {
 	};
 };
 
+&blsp1_i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	magnetometer@c {
+		compatible = "asahi-kasei,ak8963";
+		reg = <0xc>;
+		interrupts-extended = <&tlmm 38 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&pm8226_l19>;
+		pinctrl-0 = <&mag_int_default &mag_reset_default>;
+		pinctrl-names = "default";
+	};
+
+	accelerometer@18 {
+		compatible = "st,lis3dh-accel";
+		reg = <0x18>;
+		interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		pinctrl-0 = <&accel_int_default>;
+		pinctrl-names = "default";
+		st,drdy-int-pin = <1>;
+	};
+};
+
 &blsp1_i2c3 {
+	clock-frequency = <400000>;
 	status = "okay";
 
+	regulator@3e {
+		compatible = "ti,tps65132";
+		reg = <0x3e>;
+		pinctrl-0 = <&reg_lcd_default>;
+		pinctrl-names = "default";
+
+		reg_lcd_pos: outp {
+			regulator-name = "outp";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		};
+
+		reg_lcd_neg: outn {
+			regulator-name = "outn";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	sensor@48 {
 		compatible = "ti,tmp108";
 		reg = <0x48>;
+		interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&temp_alert_default>;
+		pinctrl-names = "default";
+		#thermal-sensor-cells = <0>;
 	};
 };
 
@@ -278,6 +349,56 @@  &smbb {
 	status = "okay";
 };
 
+&tlmm {
+	accel_int_default: accel-int-default-state {
+		pins = "gpio1";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	disp_vddio_default: disp-vddio-default-state {
+		pins = "gpio34";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	mag_int_default: mag-int-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_reset_default: mag-reset-default-state {
+		pins = "gpio62";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	reg_lcd_default: reg-lcd-default-state {
+		pins = "gpio31", "gpio33";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	temp_alert_default: temp-alert-default-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+};
+
 &usb {
 	extcon = <&smbb>;
 	dr_mode = "peripheral";