diff mbox series

[v2,1/3] ARM: dts: qcom: msm8926-motorola-peregrine: Add accelerometer, magnetometer, regulator

Message ID 20240617-peregrine-v2-1-c8835d2da7af@apitzsch.eu (mailing list archive)
State Accepted
Headers show
Series ARM: dts: qcom: msm8926-motorola-peregrine: Update device tree of Motorola Moto G 4G (2013) | expand

Commit Message

André Apitzsch via B4 Relay June 17, 2024, 9:22 p.m. UTC 
From: André Apitzsch <git@apitzsch.eu>

Add the accelerometer, magnetometer and regulator that are present on
the Motorola Moto G 4G (2013) device.

Signed-off-by: André Apitzsch <git@apitzsch.eu>
---
 .../dts/qcom/qcom-msm8926-motorola-peregrine.dts   | 85 ++++++++++++++++++++++
 1 file changed, 85 insertions(+)

Comments

Konrad Dybcio June 18, 2024, 11:53 a.m. UTC | #1 
On 6/17/24 23:22, André Apitzsch via B4 Relay wrote:
> From: André Apitzsch <git@apitzsch.eu>
> 
> Add the accelerometer, magnetometer and regulator that are present on
> the Motorola Moto G 4G (2013) device.
> 
> Signed-off-by: André Apitzsch <git@apitzsch.eu>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
index 0cbe2d2fbbb1..50ae3cfc95bb 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
@@ -68,9 +68,60 @@  smem_region: smem@fa00000 {
 	};
 };
 
+&blsp1_i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	magnetometer@c {
+		compatible = "asahi-kasei,ak8963";
+		reg = <0xc>;
+		interrupts-extended = <&tlmm 38 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&pm8226_l19>;
+		pinctrl-0 = <&mag_int_default &mag_reset_default>;
+		pinctrl-names = "default";
+	};
+
+	accelerometer@18 {
+		compatible = "st,lis3dh-accel";
+		reg = <0x18>;
+		interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		pinctrl-0 = <&accel_int_default>;
+		pinctrl-names = "default";
+		st,drdy-int-pin = <1>;
+	};
+};
+
 &blsp1_i2c3 {
+	clock-frequency = <400000>;
 	status = "okay";
 
+	regulator@3e {
+		compatible = "ti,tps65132";
+		reg = <0x3e>;
+		pinctrl-0 = <&reg_lcd_default>;
+		pinctrl-names = "default";
+
+		reg_lcd_pos: outp {
+			regulator-name = "outp";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		};
+
+		reg_lcd_neg: outn {
+			regulator-name = "outn";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	sensor@48 {
 		compatible = "ti,tmp108";
 		reg = <0x48>;
@@ -278,6 +329,40 @@  &smbb {
 	status = "okay";
 };
 
+&tlmm {
+	accel_int_default: accel-int-default-state {
+		pins = "gpio1";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_int_default: mag-int-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_reset_default: mag-reset-default-state {
+		pins = "gpio62";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	reg_lcd_default: reg-lcd-default-state {
+		pins = "gpio31", "gpio33";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+};
+
 &usb {
 	extcon = <&smbb>;
 	dr_mode = "peripheral";