diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index fd4c7c41ddc4..48ec781fa1d8 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -58,10 +58,13 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86518.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86528.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-yiming-uz801v3.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8929-wingtech-wt82918hd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-huawei-kiwi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-longcheer-l9100.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-samsung-a7.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-sony-xperia-kanuti-tulip.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-wingtech-wt82918.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-wingtech-wt82918hd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-motorola-potter.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-daisy.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-mido.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8929-pm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8929-pm8916.dtsi
new file mode 100644
index 000000000000..c2bf25997e9b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8929-pm8916.dtsi
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * msm8929-pm8916.dtsi describes common properties (e.g. regulator connections)
+ * that apply to most devices that make use of the MSM8929 SoC and PM8916 PMIC.
+ * Many regulators have a fixed purpose in the original reference design and
+ * were rarely re-used for different purposes. Devices that deviate from the
+ * typical reference design should not make use of this include and instead add
+ * the necessary properties in the board-specific device tree.
+ */
+
+#include "msm8929.dtsi"
+#include "pm8916.dtsi"
+
+&mdss_dsi0 {
+	vdda-supply = <&pm8916_l2>;
+	vddio-supply = <&pm8916_l6>;
+};
+
+&mdss_dsi0_phy {
+	vddio-supply = <&pm8916_l6>;
+};
+
+&mdss_dsi1 {
+	vdda-supply = <&pm8916_l2>;
+	vddio-supply = <&pm8916_l6>;
+};
+
+&mdss_dsi1_phy {
+	vddio-supply = <&pm8916_l6>;
+};
+
+&mpss {
+	pll-supply = <&pm8916_l7>;
+};
+
+&pm8916_codec {
+	vdd-cdc-io-supply = <&pm8916_l5>;
+	vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>;
+	vdd-micbias-supply = <&pm8916_l13>;
+};
+
+&rpm_requests {
+	pm8916_rpm_regulators: regulators {
+		compatible = "qcom,rpm-pm8916-regulators";
+		vdd_l1_l2_l3-supply = <&pm8916_s3>;
+		vdd_l4_l5_l6-supply = <&pm8916_s4>;
+		vdd_l7-supply = <&pm8916_s4>;
+
+		/* pm8916_s1 is managed by rpmpd (MSM8939_VDDMDCX) */
+		/* pm8916_s2 is managed by rpmpd (MSM8939_VDDCX) */
+		pm8916_s3: s3 {
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-always-on; /* Needed for L2 */
+		};
+		pm8916_s4: s4 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-always-on; /* Needed for L5/L7 */
+		};
+
+		/*
+		 * Some of the regulators are unused or managed by another
+		 * processor (e.g. the modem). We should still define nodes for
+		 * them to ensure the vote from the application processor can be
+		 * dropped in case the regulators are already on during boot.
+		 *
+		 * The labels for these nodes are omitted on purpose because
+		 * boards should configure a proper voltage before using them.
+		 */
+		l1 {};
+
+		pm8916_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-always-on; /* Needed for LPDDR RAM */
+		};
+
+		/* pm8916_l3 is managed by rpmpd (MSM8939_VDDMX) */
+
+		l4 {};
+
+		pm8916_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on; /* Needed for most digital I/O */
+		};
+
+		pm8916_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8916_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on; /* Needed for CPU PLL */
+		};
+
+		pm8916_l8: l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		pm8916_l9: l9 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		l10 {};
+
+		pm8916_l11: l11 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+			regulator-system-load = <200000>;
+		};
+
+		pm8916_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8916_l13: l13 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		l14 {};
+		l15 {};
+		l16 {};
+		l17 {};
+		l18 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8916_l8>;
+	vqmmc-supply = <&pm8916_l5>;
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8916_l11>;
+	vqmmc-supply = <&pm8916_l12>;
+};
+
+&usb_hs_phy {
+	v1p8-supply = <&pm8916_l7>;
+	v3p3-supply = <&pm8916_l13>;
+};
+
+&wcnss {
+	vddpx-supply = <&pm8916_l7>;
+};
+
+&wcnss_iris {
+	vddxo-supply = <&pm8916_l7>;
+	vddrfa-supply = <&pm8916_s3>;
+	vddpa-supply = <&pm8916_l9>;
+	vdddig-supply = <&pm8916_l5>;
+};
+
diff --git a/arch/arm64/boot/dts/qcom/msm8929-wingtech-wt82918hd.dts b/arch/arm64/boot/dts/qcom/msm8929-wingtech-wt82918hd.dts
new file mode 100644
index 000000000000..8feecffb16bf
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8929-wingtech-wt82918hd.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8929-pm8916.dtsi"
+#include "msm8939-wingtech-wt82918.dtsi"
+
+/ {
+	model = "Lenovo Vibe K5 (HD) (Wingtech WT82918)";
+	compatible = "wingtech,wt82918hd", "qcom,msm8929";
+	chassis-type = "handset";
+};
+
+&touchscreen {
+	touchscreen-size-x = <720>;
+	touchscreen-size-y = <1280>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8929.dtsi b/arch/arm64/boot/dts/qcom/msm8929.dtsi
new file mode 100644
index 000000000000..ef7bb1ced954
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8929.dtsi
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8939.dtsi"
+
+&opp_table {
+	/delete-node/ opp-550000000;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918.dts b/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918.dts
new file mode 100644
index 000000000000..aa6b699aa2a1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8939-pm8916.dtsi"
+#include "msm8939-wingtech-wt82918.dtsi"
+
+/ {
+	model = "Lenovo Vibe K5 (Wingtech WT82918)";
+	compatible = "wingtech,wt82918", "qcom,msm8939";
+	chassis-type = "handset";
+};
+
+&touchscreen {
+	touchscreen-size-x = <1080>;
+	touchscreen-size-y = <1920>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918.dtsi b/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918.dtsi
new file mode 100644
index 000000000000..800e0747a2f7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918.dtsi
@@ -0,0 +1,252 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8916-modem-qdsp6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+/ {
+	aliases {
+		mmc0 = &sdhc_1; /* eMMC */
+		mmc1 = &sdhc_2; /* SD card */
+		serial0 = &blsp_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pm8916_pwm 0 100000>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <128>;
+	};
+
+	flash-led-controller {
+		compatible = "sgmicro,sgm3140";
+		enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		flash-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&camera_front_flash_default>;
+		pinctrl-names = "default";
+
+		flash_led: led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_keys_default>;
+		pinctrl-names = "default";
+
+		label = "GPIO Buttons";
+
+		button-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&gpio_leds_default>;
+		pinctrl-names = "default";
+
+		led-0 {
+			gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_CHARGING;
+			color = <LED_COLOR_ID_RED>;
+			default-state = "off";
+			retain-state-suspended;
+		};
+
+		led-1 {
+			gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			retain-state-suspended;
+		};
+	};
+
+	usb_id: usb-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&usb_id_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&blsp_i2c2 {
+	status = "okay";
+
+	accelerometer@68 {
+		compatible = "invensense,icm20608";
+		reg = <0x68>;
+
+		interrupts-extended = <&tlmm 115 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-0 = <&accelerometer_default>;
+		pinctrl-names = "default";
+
+		vdd-supply = <&pm8916_l17>;
+		vddio-supply = <&pm8916_l6>;
+
+		mount-matrix = "-1", "0", "0",
+				"0", "1", "0",
+				"0", "0", "1";
+	};
+};
+
+&blsp_i2c5 {
+	status = "okay";
+
+	touchscreen: touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+
+		interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-names = "default";
+
+		vcc-supply = <&pm8916_l17>;
+		iovcc-supply = <&pm8916_l6>;
+
+		reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&blsp_uart2 {
+	status = "okay";
+};
+
+&mpss_mem {
+	reg = <0x0 0x86800000 0x0 0x5500000>;
+};
+
+&pm8916_pwm {
+	pinctrl-0 = <&pwm_out>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&pm8916_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8916_rpm_regulators {
+	pm8916_l17: l17 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+	};
+};
+
+&pm8916_vib {
+	status = "okay";
+};
+
+&sdhc_1 {
+	status = "okay";
+};
+
+&sdhc_2 {
+	pinctrl-0 = <&sdc2_default>;
+	pinctrl-1 = <&sdc2_sleep>;
+	pinctrl-names = "default", "sleep";
+	non-removable;
+	status = "okay";
+};
+
+&usb {
+	extcon = <&usb_id>, <&usb_id>;
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&usb_id>;
+};
+
+&wcnss {
+	status = "okay";
+};
+
+&wcnss_iris {
+	compatible = "qcom,wcn3620";
+};
+
+&wcnss_mem {
+	status = "okay";
+};
+
+&tlmm {
+	accelerometer_default: accelerometer-default-state {
+		pins = "gpio115";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	camera_front_flash_default: camera-front-flash-default-state {
+		pins = "gpio31", "gpio32";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	gpio_keys_default: gpio-keys-default-state {
+		pins = "gpio107";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	gpio_leds_default: gpio-leds-default-state {
+		pins = "gpio36", "gpio69";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	touchscreen_default: touchscreen-default-state {
+		reset-pins {
+			pins = "gpio12";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		touchscreen-pins {
+			pins = "gpio13";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	usb_id_default: usb-id-default-state {
+		pins = "gpio110";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+};
+
+&pm8916_mpps {
+	pwm_out: mpp4-state {
+		pins = "mpp4";
+		function = "digital";
+		power-source = <PM8916_MPP_VPH>;
+		output-low;
+		qcom,dtest = <1>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918hd.dts b/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918hd.dts
new file mode 100644
index 000000000000..59414db42508
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8939-wingtech-wt82918hd.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8939-pm8916.dtsi"
+#include "msm8939-wingtech-wt82918.dtsi"
+
+/ {
+	model = "Lenovo Vibe K5 (HD) (Wingtech WT82918)";
+	compatible = "wingtech,wt82918hdhw39", "qcom,msm8939";
+	chassis-type = "handset";
+};
+
+&touchscreen {
+	touchscreen-size-x = <720>;
+	touchscreen-size-y = <1280>;
+};
