diff mbox series

[3/5] arm64: dts: qcom: qcs8300-ride: enable ethernet0

Message ID 20241010-dts_qcs8300-v1-3-bf5acf05830b@quicinc.com (mailing list archive)
State Superseded
Headers show
Series Enable ethernet for qcs8300 | expand

Commit Message

Yijie Yang Oct. 10, 2024, 2:57 a.m. UTC 
Enable the SerDes PHY on qcs8300-ride.
Add the MDC and MDIO pin functions for ethernet0 on qcs8300-ride.
Enable the first 1Gb ethernet port on qcs8300-ride development board.

Signed-off-by: Yijie Yang <quic_yijiyang@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 112 ++++++++++++++++++++++++++++++
 1 file changed, 112 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
index 7eed19a694c3..b1c9f2cb9749 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
@@ -210,6 +210,95 @@  vreg_l9c: ldo9 {
 	};
 };
 
+&ethernet0 {
+	phy-mode = "sgmii";
+	phy-handle = <&sgmii_phy0>;
+
+	pinctrl-0 = <&ethernet0_default>;
+	pinctrl-names = "default";
+
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+	snps,ps-speed = <1000>;
+
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sgmii_phy0: phy@8 {
+			compatible = "ethernet-phy-id0141.0dd4";
+			reg = <0x8>;
+			device_type = "ethernet-phy";
+			interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <11000>;
+			reset-deassert-us = <70000>;
+		};
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <4>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <4>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
+};
+
 &gcc {
 	clocks = <&rpmhcc RPMH_CXO_CLK>,
 		 <&sleep_clk>,
@@ -247,6 +336,29 @@  &rpmhcc {
 	clock-names = "xo";
 };
 
+&serdes0 {
+	phy-supply = <&vreg_l5a>;
+	status = "okay";
+};
+
+&tlmm {
+	ethernet0_default: ethernet0-default-state {
+		ethernet0_mdc: ethernet0-mdc-pins {
+			pins = "gpio5";
+			function = "emac0_mdc";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		ethernet0_mdio: ethernet0-mdio-pins {
+			pins = "gpio6";
+			function = "emac0_mdio";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+	};
+};
+
 &uart7 {
 	status = "okay";
 };