| Message ID | 20241017042300.872963-4-quic_liuxin@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Enable UFS on QCS615 | expand |
On 17.10.2024 6:22 AM, Xin Liu wrote: > From: Sayali Lokhande <quic_sayalil@quicinc.com> > > Add the UFS Host Controller node and its PHY for QCS615 SoC. > > Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com> > Co-developed-by: Xin Liu <quic_liuxin@quicinc.com> > Signed-off-by: Xin Liu <quic_liuxin@quicinc.com> > --- + Taniya (see below) > arch/arm64/boot/dts/qcom/qcs615.dtsi | 74 ++++++++++++++++++++++++++++ > 1 file changed, 74 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/qcs615.dtsi b/arch/arm64/boot/dts/qcom/qcs615.dtsi > index fcba83fca7cf..689418466dc2 100644 > --- a/arch/arm64/boot/dts/qcom/qcs615.dtsi > +++ b/arch/arm64/boot/dts/qcom/qcs615.dtsi > @@ -458,6 +458,80 @@ mmss_noc: interconnect@1740000 { > qcom,bcm-voters = <&apps_bcm_voter>; > }; > > + ufs_mem_hc: ufs@1d84000 { ufshc@ would be consistent with other files in dts/qcom > + compatible = "qcom,qcs615-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; > + reg = <0x0 0x01d84000 0x0 0x3000>, <0x0 0x01d90000 0x0 0x8000>; > + reg-names = "std", "ice"; One per line, please > + interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; > + phys = <&ufs_mem_phy>; > + phy-names = "ufsphy"; > + lanes-per-direction = <1>; > + #reset-cells = <1>; > + resets = <&gcc GCC_UFS_PHY_BCR>; > + reset-names = "rst"; > + > + power-domains = <&gcc UFS_PHY_GDSC>; > + required-opps = <&rpmhpd_opp_nom>; > + > + iommus = <&apps_smmu 0x300 0x0>; > + dma-coherent; > + > + interconnects = <&aggre1_noc MASTER_UFS_MEM QCOM_ICC_TAG_ALWAYS > + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, > + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS > + &config_noc SLAVE_UFS_MEM_CFG QCOM_ICC_TAG_ALWAYS>; > + interconnect-names = "ufs-ddr", > + "cpu-ufs"; > + > + clocks = <&gcc GCC_UFS_PHY_AXI_CLK>, > + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, > + <&gcc GCC_UFS_PHY_AHB_CLK>, > + <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, > + <&rpmhcc RPMH_CXO_CLK>, > + <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, > + <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, > + <&gcc GCC_UFS_PHY_ICE_CORE_CLK>; > + clock-names = "core_clk", > + "bus_aggr_clk", > + "iface_clk", > + "core_clk_unipro", > + "ref_clk", > + "tx_lane0_sync_clk", > + "rx_lane0_sync_clk", > + "ice_core_clk"; > + freq-table-hz = <50000000 200000000>, > + <0 0>, > + <0 0>, > + <37500000 150000000>, > + <0 0>, > + <0 0>, > + <0 0>, > + <75000000 300000000>; Please try to match the order of properties present in sm8650.dtsi And please use an OPP table instead of freq-table-hz (see sm8*5*50.dtsi) > + > + status = "disabled"; > + }; > + > + ufs_mem_phy: phy@1d87000 { > + compatible = "qcom,qcs615-qmp-ufs-phy", "qcom,sm6115-qmp-ufs-phy"; > + reg = <0x0 0x01d87000 0x0 0xe00>; This register region is a bit longer > + clocks = <&rpmhcc RPMH_CXO_CLK>, > + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>, > + <&gcc GCC_UFS_MEM_CLKREF_CLK>; > + clock-names = "ref", > + "ref_aux", > + "qref"; > + > + power-domains = <&gcc UFS_PHY_GDSC>; > + > + resets = <&ufs_mem_hc 0>; > + reset-names = "ufsphy"; > + > + #clock-cells = <1>; The PHY is a clock provider. Normally, it's a parent of gcc_ufs_phy_[rt]x_symbol_n clocks. Taniya, could you please wire that up in your patchset? Konrad
在 2024/10/26 3:24, Konrad Dybcio 写道: > On 17.10.2024 6:22 AM, Xin Liu wrote: >> From: Sayali Lokhande <quic_sayalil@quicinc.com> >> >> Add the UFS Host Controller node and its PHY for QCS615 SoC. >> >> Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com> >> Co-developed-by: Xin Liu <quic_liuxin@quicinc.com> >> Signed-off-by: Xin Liu <quic_liuxin@quicinc.com> >> --- > > + Taniya (see below) > >> arch/arm64/boot/dts/qcom/qcs615.dtsi | 74 ++++++++++++++++++++++++++++ >> 1 file changed, 74 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/qcs615.dtsi b/arch/arm64/boot/dts/qcom/qcs615.dtsi >> index fcba83fca7cf..689418466dc2 100644 >> --- a/arch/arm64/boot/dts/qcom/qcs615.dtsi >> +++ b/arch/arm64/boot/dts/qcom/qcs615.dtsi >> @@ -458,6 +458,80 @@ mmss_noc: interconnect@1740000 { >> qcom,bcm-voters = <&apps_bcm_voter>; >> }; >> >> + ufs_mem_hc: ufs@1d84000 { > > ufshc@ would be consistent with other files in dts/qcom > I referred to qcom files such as sa8775p/sm8550/sm8650 etc.All use ufs@ > >> + compatible = "qcom,qcs615-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; >> + reg = <0x0 0x01d84000 0x0 0x3000>, <0x0 0x01d90000 0x0 0x8000>; >> + reg-names = "std", "ice"; > > One per line, please Thank you, I will fix it next version. > >> + interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; >> + phys = <&ufs_mem_phy>; >> + phy-names = "ufsphy"; >> + lanes-per-direction = <1>; >> + #reset-cells = <1>; >> + resets = <&gcc GCC_UFS_PHY_BCR>; >> + reset-names = "rst"; >> + >> + power-domains = <&gcc UFS_PHY_GDSC>; >> + required-opps = <&rpmhpd_opp_nom>; >> + >> + iommus = <&apps_smmu 0x300 0x0>; >> + dma-coherent; >> + >> + interconnects = <&aggre1_noc MASTER_UFS_MEM QCOM_ICC_TAG_ALWAYS >> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, >> + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS >> + &config_noc SLAVE_UFS_MEM_CFG QCOM_ICC_TAG_ALWAYS>; >> + interconnect-names = "ufs-ddr", >> + "cpu-ufs"; >> + >> + clocks = <&gcc GCC_UFS_PHY_AXI_CLK>, >> + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, >> + <&gcc GCC_UFS_PHY_AHB_CLK>, >> + <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, >> + <&rpmhcc RPMH_CXO_CLK>, >> + <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, >> + <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, >> + <&gcc GCC_UFS_PHY_ICE_CORE_CLK>; >> + clock-names = "core_clk", >> + "bus_aggr_clk", >> + "iface_clk", >> + "core_clk_unipro", >> + "ref_clk", >> + "tx_lane0_sync_clk", >> + "rx_lane0_sync_clk", >> + "ice_core_clk"; >> + freq-table-hz = <50000000 200000000>, >> + <0 0>, >> + <0 0>, >> + <37500000 150000000>, >> + <0 0>, >> + <0 0>, >> + <0 0>, >> + <75000000 300000000>; > > Please try to match the order of properties present in sm8650.dtsi Thank you, I will fix it next version. > > And please use an OPP table instead of freq-table-hz (see sm8*5*50.dtsi) Thank you, I will fix it next version. > >> + >> + status = "disabled"; >> + }; >> + >> + ufs_mem_phy: phy@1d87000 { >> + compatible = "qcom,qcs615-qmp-ufs-phy", "qcom,sm6115-qmp-ufs-phy"; >> + reg = <0x0 0x01d87000 0x0 0xe00>; > > This register region is a bit longer I just confirmed again, there's no problem here. > >> + clocks = <&rpmhcc RPMH_CXO_CLK>, >> + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>, >> + <&gcc GCC_UFS_MEM_CLKREF_CLK>; >> + clock-names = "ref", >> + "ref_aux", >> + "qref"; >> + >> + power-domains = <&gcc UFS_PHY_GDSC>; >> + >> + resets = <&ufs_mem_hc 0>; >> + reset-names = "ufsphy"; >> + >> + #clock-cells = <1>; > > The PHY is a clock provider. Normally, it's a parent of > gcc_ufs_phy_[rt]x_symbol_n clocks. > > Taniya, could you please wire that up in your patchset? > > Konrad
On Wed, Nov 13, 2024 at 05:19:49PM +0800, Xin Liu wrote: > > > 在 2024/10/26 3:24, Konrad Dybcio 写道: > > On 17.10.2024 6:22 AM, Xin Liu wrote: > > > From: Sayali Lokhande <quic_sayalil@quicinc.com> > > > > > > Add the UFS Host Controller node and its PHY for QCS615 SoC. > > > > > > Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com> > > > Co-developed-by: Xin Liu <quic_liuxin@quicinc.com> > > > Signed-off-by: Xin Liu <quic_liuxin@quicinc.com> > > > --- > > > > + Taniya (see below) > > > > > arch/arm64/boot/dts/qcom/qcs615.dtsi | 74 ++++++++++++++++++++++++++++ > > > 1 file changed, 74 insertions(+) > > > > > > diff --git a/arch/arm64/boot/dts/qcom/qcs615.dtsi b/arch/arm64/boot/dts/qcom/qcs615.dtsi > > > index fcba83fca7cf..689418466dc2 100644 > > > --- a/arch/arm64/boot/dts/qcom/qcs615.dtsi > > > +++ b/arch/arm64/boot/dts/qcom/qcs615.dtsi > > > @@ -458,6 +458,80 @@ mmss_noc: interconnect@1740000 { > > > qcom,bcm-voters = <&apps_bcm_voter>; > > > }; > > > + ufs_mem_hc: ufs@1d84000 { > > > > ufshc@ would be consistent with other files in dts/qcom > > > I referred to qcom files such as sa8775p/sm8550/sm8650 etc.All use ufs@ That's an oddity. But 'ufshc' is documented in the devicetree spec. So you should use it for UFSHC nodes. - Mani > > > > > + compatible = "qcom,qcs615-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; > > > + reg = <0x0 0x01d84000 0x0 0x3000>, <0x0 0x01d90000 0x0 0x8000>; > > > + reg-names = "std", "ice"; > > > > One per line, please > Thank you, I will fix it next version. > > > > > + interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; > > > + phys = <&ufs_mem_phy>; > > > + phy-names = "ufsphy"; > > > + lanes-per-direction = <1>; > > > + #reset-cells = <1>; > > > + resets = <&gcc GCC_UFS_PHY_BCR>; > > > + reset-names = "rst"; > > > + > > > + power-domains = <&gcc UFS_PHY_GDSC>; > > > + required-opps = <&rpmhpd_opp_nom>; > > > + > > > + iommus = <&apps_smmu 0x300 0x0>; > > > + dma-coherent; > > > + > > > + interconnects = <&aggre1_noc MASTER_UFS_MEM QCOM_ICC_TAG_ALWAYS > > > + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, > > > + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS > > > + &config_noc SLAVE_UFS_MEM_CFG QCOM_ICC_TAG_ALWAYS>; > > > + interconnect-names = "ufs-ddr", > > > + "cpu-ufs"; > > > + > > > + clocks = <&gcc GCC_UFS_PHY_AXI_CLK>, > > > + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, > > > + <&gcc GCC_UFS_PHY_AHB_CLK>, > > > + <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, > > > + <&rpmhcc RPMH_CXO_CLK>, > > > + <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, > > > + <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, > > > + <&gcc GCC_UFS_PHY_ICE_CORE_CLK>; > > > + clock-names = "core_clk", > > > + "bus_aggr_clk", > > > + "iface_clk", > > > + "core_clk_unipro", > > > + "ref_clk", > > > + "tx_lane0_sync_clk", > > > + "rx_lane0_sync_clk", > > > + "ice_core_clk"; > > > + freq-table-hz = <50000000 200000000>, > > > + <0 0>, > > > + <0 0>, > > > + <37500000 150000000>, > > > + <0 0>, > > > + <0 0>, > > > + <0 0>, > > > + <75000000 300000000>; > > > > Please try to match the order of properties present in sm8650.dtsi > Thank you, I will fix it next version. > > > > And please use an OPP table instead of freq-table-hz (see sm8*5*50.dtsi) > Thank you, I will fix it next version. > > > > > + > > > + status = "disabled"; > > > + }; > > > + > > > + ufs_mem_phy: phy@1d87000 { > > > + compatible = "qcom,qcs615-qmp-ufs-phy", "qcom,sm6115-qmp-ufs-phy"; > > > + reg = <0x0 0x01d87000 0x0 0xe00>; > > > > This register region is a bit longer > I just confirmed again, there's no problem here. > > > > > + clocks = <&rpmhcc RPMH_CXO_CLK>, > > > + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>, > > > + <&gcc GCC_UFS_MEM_CLKREF_CLK>; > > > + clock-names = "ref", > > > + "ref_aux", > > > + "qref"; > > > + > > > + power-domains = <&gcc UFS_PHY_GDSC>; > > > + > > > + resets = <&ufs_mem_hc 0>; > > > + reset-names = "ufsphy"; > > > + > > > + #clock-cells = <1>; > > > > The PHY is a clock provider. Normally, it's a parent of > > gcc_ufs_phy_[rt]x_symbol_n clocks. > > > > Taniya, could you please wire that up in your patchset? > > > > Konrad >
On 13.11.2024 10:27 AM, Manivannan Sadhasivam wrote: > On Wed, Nov 13, 2024 at 05:19:49PM +0800, Xin Liu wrote: >> >> >> 在 2024/10/26 3:24, Konrad Dybcio 写道: >>> On 17.10.2024 6:22 AM, Xin Liu wrote: >>>> From: Sayali Lokhande <quic_sayalil@quicinc.com> >>>> >>>> Add the UFS Host Controller node and its PHY for QCS615 SoC. >>>> >>>> Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com> >>>> Co-developed-by: Xin Liu <quic_liuxin@quicinc.com> >>>> Signed-off-by: Xin Liu <quic_liuxin@quicinc.com> >>>> --- [...] >>>> + >>>> + status = "disabled"; >>>> + }; >>>> + >>>> + ufs_mem_phy: phy@1d87000 { >>>> + compatible = "qcom,qcs615-qmp-ufs-phy", "qcom,sm6115-qmp-ufs-phy"; >>>> + reg = <0x0 0x01d87000 0x0 0xe00>; >>> >>> This register region is a bit longer >> I just confirmed again, there's no problem here. I'd happen to disagree, please make it 0xe10-long Konrad
On 14.11.2024 4:20 PM, Konrad Dybcio wrote: > On 13.11.2024 10:27 AM, Manivannan Sadhasivam wrote: >> On Wed, Nov 13, 2024 at 05:19:49PM +0800, Xin Liu wrote: >>> >>> >>> 在 2024/10/26 3:24, Konrad Dybcio 写道: >>>> On 17.10.2024 6:22 AM, Xin Liu wrote: >>>>> From: Sayali Lokhande <quic_sayalil@quicinc.com> >>>>> >>>>> Add the UFS Host Controller node and its PHY for QCS615 SoC. >>>>> >>>>> Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com> >>>>> Co-developed-by: Xin Liu <quic_liuxin@quicinc.com> >>>>> Signed-off-by: Xin Liu <quic_liuxin@quicinc.com> >>>>> --- > > [...] > > >>>>> + >>>>> + status = "disabled"; >>>>> + }; >>>>> + >>>>> + ufs_mem_phy: phy@1d87000 { >>>>> + compatible = "qcom,qcs615-qmp-ufs-phy", "qcom,sm6115-qmp-ufs-phy"; >>>>> + reg = <0x0 0x01d87000 0x0 0xe00>; >>>> >>>> This register region is a bit longer >>> I just confirmed again, there's no problem here. > > I'd happen to disagree, please make it 0xe10-long Ignore, I was looking at the wrong SoC. Sorry. Konrad
diff --git a/arch/arm64/boot/dts/qcom/qcs615.dtsi b/arch/arm64/boot/dts/qcom/qcs615.dtsi index fcba83fca7cf..689418466dc2 100644 --- a/arch/arm64/boot/dts/qcom/qcs615.dtsi +++ b/arch/arm64/boot/dts/qcom/qcs615.dtsi @@ -458,6 +458,80 @@ mmss_noc: interconnect@1740000 { qcom,bcm-voters = <&apps_bcm_voter>; }; + ufs_mem_hc: ufs@1d84000 { + compatible = "qcom,qcs615-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; + reg = <0x0 0x01d84000 0x0 0x3000>, <0x0 0x01d90000 0x0 0x8000>; + reg-names = "std", "ice"; + interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; + phys = <&ufs_mem_phy>; + phy-names = "ufsphy"; + lanes-per-direction = <1>; + #reset-cells = <1>; + resets = <&gcc GCC_UFS_PHY_BCR>; + reset-names = "rst"; + + power-domains = <&gcc UFS_PHY_GDSC>; + required-opps = <&rpmhpd_opp_nom>; + + iommus = <&apps_smmu 0x300 0x0>; + dma-coherent; + + interconnects = <&aggre1_noc MASTER_UFS_MEM QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_UFS_MEM_CFG QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "ufs-ddr", + "cpu-ufs"; + + clocks = <&gcc GCC_UFS_PHY_AXI_CLK>, + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&gcc GCC_UFS_PHY_AHB_CLK>, + <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, + <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, + <&gcc GCC_UFS_PHY_ICE_CORE_CLK>; + clock-names = "core_clk", + "bus_aggr_clk", + "iface_clk", + "core_clk_unipro", + "ref_clk", + "tx_lane0_sync_clk", + "rx_lane0_sync_clk", + "ice_core_clk"; + freq-table-hz = <50000000 200000000>, + <0 0>, + <0 0>, + <37500000 150000000>, + <0 0>, + <0 0>, + <0 0>, + <75000000 300000000>; + + status = "disabled"; + }; + + ufs_mem_phy: phy@1d87000 { + compatible = "qcom,qcs615-qmp-ufs-phy", "qcom,sm6115-qmp-ufs-phy"; + reg = <0x0 0x01d87000 0x0 0xe00>; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>, + <&gcc GCC_UFS_MEM_CLKREF_CLK>; + clock-names = "ref", + "ref_aux", + "qref"; + + power-domains = <&gcc UFS_PHY_GDSC>; + + resets = <&ufs_mem_hc 0>; + reset-names = "ufsphy"; + + #clock-cells = <1>; + #phy-cells = <0>; + + status = "disabled"; + }; + tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex"; reg = <0x0 0x01f40000 0x0 0x20000>;