@@ -8,6 +8,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/gpio-keys.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "x1e80100.dtsi"
@@ -277,6 +278,23 @@ vreg_edp_3p3: regulator-edp-3p3 {
regulator-boot-on;
};
+ vreg_misc_3p3: regulator-misc-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_MISC_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&misc_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vreg_nvme: regulator-nvme {
compatible = "regulator-fixed";
@@ -691,6 +709,9 @@ touchpad@15 {
hid-descr-addr = <0x1>;
interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l12b_1p2>;
+
pinctrl-0 = <&tpad_default>;
pinctrl-names = "default";
@@ -704,6 +725,9 @@ keyboard@3a {
hid-descr-addr = <0x1>;
interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l12b_1p2>;
+
pinctrl-0 = <&kybd_default>;
pinctrl-names = "default";
@@ -723,6 +747,9 @@ touchscreen@10 {
hid-descr-addr = <0x1>;
interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l15b_1p8>;
+
pinctrl-0 = <&ts0_default>;
pinctrl-names = "default";
};
@@ -856,6 +883,19 @@ &pcie6a_phy {
status = "okay";
};
+&pm8550ve_8_gpios {
+ misc_3p3_reg_en: misc-3p3-reg-en-state {
+ pins = "gpio6";
+ function = "normal";
+ bias-disable;
+ drive-push-pull;
+ input-disable;
+ output-enable;
+ power-source = <1>; /* 1.8 V */
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ };
+};
+
&pmc8380_3_gpios {
edp_bl_en: edp-bl-en-state {
pins = "gpio4";
Add the missing HID supplies to avoid relying on other consumers to keep them on. This also avoids the following warnings on boot: i2c_hid_of 0-0010: supply vdd not found, using dummy regulator i2c_hid_of 0-0010: supply vddl not found, using dummy regulator i2c_hid_of 1-0015: supply vdd not found, using dummy regulator i2c_hid_of 1-0015: supply vddl not found, using dummy regulator i2c_hid_of 1-003a: supply vdd not found, using dummy regulator i2c_hid_of 1-003a: supply vddl not found, using dummy regulator Note that VREG_MISC_3P3 is also used for things like the fingerprint reader which are not yet fully described so mark the regulator as always on for now. Fixes: d7e03cce0400 ("arm64: dts: qcom: x1e80100-crd: Enable more support") Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> --- Changes in v3 - move 'pinctrl-names' after 'pinctrl-0' Changes in v2: - amend the pin config in order not to rely on the boot firmware arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 40 +++++++++++++++++++++++ 1 file changed, 40 insertions(+)