@@ -4094,6 +4094,112 @@ lpass_lpicx_noc: interconnect@7430000 {
#interconnect-cells = <2>;
};
+ sdhc_2: mmc@8804000 {
+ compatible = "qcom,x1e80100-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0 0x08804000 0 0x1000>;
+
+ interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+ <&gcc GCC_SDCC2_APPS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "core", "xo";
+ iommus = <&apps_smmu 0x520 0>;
+ qcom,dll-config = <0x0007642c>;
+ qcom,ddr-config = <0x80040868>;
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&sdhc2_opp_table>;
+
+ interconnects = <&aggre2_noc MASTER_SDCC_2 QCOM_ICC_TAG_ALWAYS
+ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+ <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+ &config_noc SLAVE_SDCC_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
+ interconnect-names = "sdhc-ddr", "cpu-sdhc";
+ bus-width = <4>;
+ dma-coherent;
+
+ status = "disabled";
+
+ sdhc2_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-19200000 {
+ opp-hz = /bits/ 64 <19200000>;
+ required-opps = <&rpmhpd_opp_min_svs>;
+ };
+
+ opp-50000000 {
+ opp-hz = /bits/ 64 <50000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-202000000 {
+ opp-hz = /bits/ 64 <202000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
+ sdhc_4: mmc@8844000 {
+ compatible = "qcom,x1e80100-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0 0x08844000 0 0x1000>;
+
+ interrupts = <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC4_AHB_CLK>,
+ <&gcc GCC_SDCC4_APPS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "core", "xo";
+ iommus = <&apps_smmu 0x160 0>;
+ qcom,dll-config = <0x0007642c>;
+ qcom,ddr-config = <0x80040868>;
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&sdhc4_opp_table>;
+
+ interconnects = <&aggre2_noc MASTER_SDCC_4 QCOM_ICC_TAG_ALWAYS
+ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+ <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+ &config_noc SLAVE_SDCC_4 QCOM_ICC_TAG_ACTIVE_ONLY>;
+ interconnect-names = "sdhc-ddr", "cpu-sdhc";
+ bus-width = <4>;
+ dma-coherent;
+
+ status = "disabled";
+
+ sdhc4_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-19200000 {
+ opp-hz = /bits/ 64 <19200000>;
+ required-opps = <&rpmhpd_opp_min_svs>;
+ };
+
+ opp-50000000 {
+ opp-hz = /bits/ 64 <50000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-202000000 {
+ opp-hz = /bits/ 64 <202000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
usb_2_hsphy: phy@88e0000 {
compatible = "qcom,x1e80100-snps-eusb2-phy",
"qcom,sm8550-snps-eusb2-phy";
@@ -5846,6 +5952,46 @@ rx-pins {
bias-disable;
};
};
+
+ sdc2_default: sdc2-default-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdc2_sleep: sdc2-sleep-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
};
apps_smmu: iommu@15000000 {
The X Elite platform features two SDHC v5 controllers. Describe the controllers along with the pin configuration in TLMM for the SDC2, since they are hardwired and cannot be muxed to any other function. The SDC4 pin configuration can be muxed to different functions, so leave those to board specific dts. Signed-off-by: Abel Vesa <abel.vesa@linaro.org> --- arch/arm64/boot/dts/qcom/x1e80100.dtsi | 146 +++++++++++++++++++++++++++++++++ 1 file changed, 146 insertions(+)