diff mbox series

[v4,03/17] arm64: dts: qcom: sm8150: Disable USB U1/U2 entry

Message ID 20241231081115.3149850-4-quic_prashk@quicinc.com (mailing list archive)
State Accepted
Commit 20f36ce4db5b544de640b5e47ac656fdd97b4896
Headers show
Series Disable USB U1/U2 entry for QC ARM64 targets | expand

Commit Message

Prashanth K Dec. 31, 2024, 8:11 a.m. UTC 
From: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>

Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:

1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.

2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.

Disabling these intermittent power states enhances device stability
without affecting power usage.

Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index cedae8d03a51..4dbda54b47a5 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3658,6 +3658,8 @@  usb_1_dwc3: usb@a600000 {
 				iommus = <&apps_smmu 0x140 0>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
+				snps,dis-u1-entry-quirk;
+				snps,dis-u2-entry-quirk;
 				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
 				phy-names = "usb2-phy", "usb3-phy";
 
@@ -3735,6 +3737,8 @@  usb_2_dwc3: usb@a800000 {
 				iommus = <&apps_smmu 0x160 0>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
+				snps,dis-u1-entry-quirk;
+				snps,dis-u2-entry-quirk;
 				phys = <&usb_2_hsphy>, <&usb_2_qmpphy>;
 				phy-names = "usb2-phy", "usb3-phy";
 			};