@@ -17,6 +17,7 @@ / {
aliases {
serial0 = &uart21;
+ serial1 = &uart14;
};
wcd938x: audio-codec {
@@ -281,6 +282,42 @@ vreg_nvme: regulator-nvme {
regulator-boot-on;
};
+ vreg_wcn_0p95: regulator-wcn-0p95 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_0P95";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_1p9: regulator-wcn-1p9 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_1P9";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_3p3: regulator-wcn-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wcn_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
usb-1-ss0-sbu-mux {
compatible = "onnn,fsusb42", "gpio-sbu-mux";
@@ -337,6 +374,65 @@ usb_1_ss2_sbu_mux: endpoint {
};
};
};
+
+ wcn7850-pmu {
+ compatible = "qcom,wcn7850-pmu";
+
+ vdd-supply = <&vreg_wcn_0p95>;
+ vddio-supply = <&vreg_l15b_1p8>;
+ vddaon-supply = <&vreg_wcn_0p95>;
+ vdddig-supply = <&vreg_wcn_0p95>;
+ vddrfa1p2-supply = <&vreg_wcn_1p9>;
+ vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+ wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+ bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&wcn_wlan_bt_en>;
+ pinctrl-names = "default";
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
};
&apps_rsc {
@@ -825,6 +921,23 @@ &pcie4_phy {
status = "okay";
};
+&pcie4_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1107";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
&pcie6a {
perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
@@ -1135,6 +1248,37 @@ wcd_default: wcd-reset-n-active-state {
bias-disable;
output-low;
};
+
+ wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+ pins = "gpio116", "gpio117";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wcn_sw_en: wcn-sw-en-state {
+ pins = "gpio214";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+ max-speed = <3200000>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ };
};
&uart21 {
Add the WiFi/BT nodes for QCP and describe the regulators for the WCN7850 combo chip using the new power sequencing bindings. All voltages are derived from chained fixed regulators controlled using a single GPIO. The same setup also works for CRD (and likely most of the other X1E80100 laptops). However, unlike the QCP they use soldered or removable M.2 cards supplied by a single 3.3V fixed regulator. The other necessary voltages are then derived inside the M.2 card. Describing this properly requires new bindings, so this commit only adds QCP for now. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> --- Changes in v3: - Fix node ordering (Johan) - Link to v2: https://lore.kernel.org/r/20250211-x1e80100-pwrseq-qcp-v2-1-c4349ca974ab@linaro.org Changes in v2: - Rebase on qcom for-next, patch 1-2 were applied already - Mention dummy regulator warning - Link to v1: https://lore.kernel.org/r/20241007-x1e80100-pwrseq-qcp-v1-0-f7166510ab17@linaro.org --- The Linux driver currently warns about a missing regulator supply: pwrseq-qcom_wcn wcn7850-pmu: supply vddio1p2 not found, using dummy regulator This supply exists on the WCN7850 chip, but nothing is connected there on the QCP. Bartosz is working on hiding this warning in the driver. Since the DT is correct and the same setup is already used on SM8550 upstream, this doesn't block this patch. --- arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 144 ++++++++++++++++++++++++++++++ 1 file changed, 144 insertions(+) --- base-commit: c177fed7617d6306541305e93e575c0c01600ff0 change-id: 20241007-x1e80100-pwrseq-qcp-2bf898c60353 Best regards,