new file mode 100644
@@ -0,0 +1,160 @@
+Qualcomm Technologies, Inc. RPMh Regulators
+
+rpmh-regulator devices support PMIC regulator management via the Voltage
+Regulator Manager (VRM) and Oscillator Buffer (XOB) RPMh accelerators. The APPS
+processor communicates with these hardware blocks via a Resource State
+Coordinator (RSC) using command packets. The VRM allows changing three
+parameters for a given regulator: enable state, output voltage, and operating
+mode. The XOB allows changing only a single parameter for a given regulator:
+its enable state. Despite its name, the XOB is capable of controlling the
+enable state of any PMIC peripheral. It is used for clock buffers, low-voltage
+switches, and LDO/SMPS regulators which have a fixed voltage and mode.
+
+=======================
+Required Node Structure
+=======================
+
+RPMh regulators must be described in two levels of device nodes. The first
+level describes the PMIC containing the regulators and must reside within an
+RPMh device node. The second level describes each regulator within the PMIC
+which is to be used on the board. Each of these regulators maps to a single
+RPMh resource.
+
+The names used for regulator nodes must match those supported by a given PMIC.
+Supported regulator node names:
+ PM8998: smps1 - smps13, ldo1 - ldo28, lvs1 - lvs2
+ PMI8998: bob
+ PM8005: smps1 - smps4
+
+========================
+First Level Nodes - PMIC
+========================
+
+- compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must be one of: "qcom,pm8998-rpmh-regulators",
+ "qcom,pmi8998-rpmh-regulators" or
+ "qcom,pm8005-rpmh-regulators".
+
+- qcom,pmic-id
+ Usage: required
+ Value type: <string>
+ Definition: RPMh resource name suffix used for the regulators found on
+ this PMIC. Typical values: "a", "b", "c", "d", "e", "f".
+
+- vdd-s1-supply
+- vdd-s2-supply
+- vdd-s3-supply
+- vdd-s4-supply
+ Usage: optional (PM8998 and PM8005 only)
+ Value type: <phandle>
+ Definition: phandle of the parent supply regulator of one or more of the
+ regulators for this PMIC.
+
+- vdd-s5-supply
+- vdd-s6-supply
+- vdd-s7-supply
+- vdd-s8-supply
+- vdd-s9-supply
+- vdd-s10-supply
+- vdd-s11-supply
+- vdd-s12-supply
+- vdd-s13-supply
+- vdd-l1-l27-supply
+- vdd-l2-l8-l17-supply
+- vdd-l3-l11-supply
+- vdd-l4-l5-supply
+- vdd-l6-supply
+- vdd-l7-l12-l14-l15-supply
+- vdd-l9-supply
+- vdd-l10-l23-l25-supply
+- vdd-l13-l19-l21-supply
+- vdd-l16-l28-supply
+- vdd-l18-l22-supply
+- vdd-l20-l24-supply
+- vdd-l26-supply
+- vin-lvs-1-2-supply
+ Usage: optional (PM8998 only)
+ Value type: <phandle>
+ Definition: phandle of the parent supply regulator of one or more of the
+ regulators for this PMIC.
+
+- vdd-bob-supply
+ Usage: optional (PMI8998 only)
+ Value type: <phandle>
+ Definition: BOB regulator parent supply phandle
+
+===============================
+Second Level Nodes - Regulators
+===============================
+
+- qcom,always-wait-for-ack
+ Usage: optional
+ Value type: <empty>
+ Definition: Boolean flag which indicates that the application processor
+ must wait for an ACK or a NACK from RPMh for every request
+ sent for this regulator including those which are for a
+ strictly lower power state.
+
+Other properties defined in Documentation/devicetree/bindings/regulator.txt
+may also be used. regulator-initial-mode and regulator-allowed-modes may be
+specified for VRM regulators using mode values from
+include/dt-bindings/regulator/qcom,rpmh-regulator.h. regulator-allow-bypass
+may be specified for BOB type regulators managed via VRM.
+regulator-allow-set-load may be specified for LDO type regulators managed via
+VRM.
+
+========
+Examples
+========
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+&apps_rsc {
+ pm8998-rpmh-regulators {
+ compatible = "qcom,pm8998-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-l7-l12-l14-l15-supply = <&pm8998_s5>;
+
+ smps2 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ pm8998_s5: smps5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allowed-modes =
+ <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ lvs1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+
+ pmi8998-rpmh-regulators {
+ compatible = "qcom,pmi8998-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-allowed-modes =
+ <RPMH_REGULATOR_MODE_AUTO
+ RPMH_REGULATOR_MODE_HPM>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2018, The Linux Foundation. All rights reserved. */
+
+#ifndef __QCOM_RPMH_REGULATOR_H
+#define __QCOM_RPMH_REGULATOR_H
+
+/*
+ * These mode constants may be used to specify modes for various RPMh regulator
+ * device tree properties (e.g. regulator-initial-mode). Each type of regulator
+ * supports a subset of the possible modes.
+ *
+ * %RPMH_REGULATOR_MODE_RET: Retention mode in which only an extremely small
+ * load current is allowed. This mode is supported
+ * by LDO and SMPS type regulators.
+ * %RPMH_REGULATOR_MODE_LPM: Low power mode in which a small load current is
+ * allowed. This mode corresponds to PFM for SMPS
+ * and BOB type regulators. This mode is supported
+ * by LDO, HFSMPS, BOB, and PMIC4 FTSMPS type
+ * regulators.
+ * %RPMH_REGULATOR_MODE_AUTO: Auto mode in which the regulator hardware
+ * automatically switches between LPM and HPM based
+ * upon the real-time load current. This mode is
+ * supported by HFSMPS, BOB, and PMIC4 FTSMPS type
+ * regulators.
+ * %RPMH_REGULATOR_MODE_HPM: High power mode in which the full rated current
+ * of the regulator is allowed. This mode
+ * corresponds to PWM for SMPS and BOB type
+ * regulators. This mode is supported by all types
+ * of regulators.
+ */
+#define RPMH_REGULATOR_MODE_RET 0
+#define RPMH_REGULATOR_MODE_LPM 1
+#define RPMH_REGULATOR_MODE_AUTO 2
+#define RPMH_REGULATOR_MODE_HPM 3
+
+#endif