@@ -7,3 +7,18 @@ menuconfig SPMI
SPMI (System Power Management Interface) is a two-wire
serial interface between baseband and application processors
and Power Management Integrated Circuits (PMIC).
+
+if SPMI
+
+config SPMI_MSM_PMIC_ARB
+ tristate "Qualcomm MSM SPMI Controller (PMIC Arbiter)"
+ depends on ARCH_MSM
+ help
+ If you say yes to this option, support will be included for the
+ built-in SPMI PMIC Arbiter interface on Qualcomm MSM family
+ processors.
+
+ This is required for communicating with Qualcomm PMICs and
+ other devices that have the SPMI interface.
+
+endif
@@ -2,3 +2,5 @@
# Makefile for kernel SPMI framework.
#
obj-$(CONFIG_SPMI) += spmi.o
+
+obj-$(CONFIG_SPMI_MSM_PMIC_ARB) += spmi-pmic-arb.o
new file mode 100644
@@ -0,0 +1,403 @@
+/* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+#include <linux/spmi.h>
+
+/* PMIC Arbiter configuration registers */
+#define PMIC_ARB_VERSION 0x0000
+#define PMIC_ARB_INT_EN 0x0004
+
+/* PMIC Arbiter channel registers */
+#define PMIC_ARB_CMD(N) (0x0800 + (0x80 * (N)))
+#define PMIC_ARB_CONFIG(N) (0x0804 + (0x80 * (N)))
+#define PMIC_ARB_STATUS(N) (0x0808 + (0x80 * (N)))
+#define PMIC_ARB_WDATA0(N) (0x0810 + (0x80 * (N)))
+#define PMIC_ARB_WDATA1(N) (0x0814 + (0x80 * (N)))
+#define PMIC_ARB_RDATA0(N) (0x0818 + (0x80 * (N)))
+#define PMIC_ARB_RDATA1(N) (0x081C + (0x80 * (N)))
+
+/* Interrupt Controller */
+#define SPMI_PIC_OWNER_ACC_STATUS(M, N) (0x0000 + ((32 * (M)) + (4 * (N))))
+#define SPMI_PIC_ACC_ENABLE(N) (0x0200 + (4 * (N)))
+#define SPMI_PIC_IRQ_STATUS(N) (0x0600 + (4 * (N)))
+#define SPMI_PIC_IRQ_CLEAR(N) (0x0A00 + (4 * (N)))
+
+/* Mapping Table */
+#define SPMI_MAPPING_TABLE_REG(N) (0x0B00 + (4 * (N)))
+#define SPMI_MAPPING_BIT_INDEX(X) (((X) >> 18) & 0xF)
+#define SPMI_MAPPING_BIT_IS_0_FLAG(X) (((X) >> 17) & 0x1)
+#define SPMI_MAPPING_BIT_IS_0_RESULT(X) (((X) >> 9) & 0xFF)
+#define SPMI_MAPPING_BIT_IS_1_FLAG(X) (((X) >> 8) & 0x1)
+#define SPMI_MAPPING_BIT_IS_1_RESULT(X) (((X) >> 0) & 0xFF)
+
+#define SPMI_MAPPING_TABLE_LEN 255
+#define SPMI_MAPPING_TABLE_TREE_DEPTH 16 /* Maximum of 16-bits */
+
+/* Ownership Table */
+#define SPMI_OWNERSHIP_TABLE_REG(N) (0x0700 + (4 * (N)))
+#define SPMI_OWNERSHIP_PERIPH2OWNER(X) ((X) & 0x7)
+
+/* Channel Status fields */
+enum pmic_arb_chnl_status {
+ PMIC_ARB_STATUS_DONE = (1 << 0),
+ PMIC_ARB_STATUS_FAILURE = (1 << 1),
+ PMIC_ARB_STATUS_DENIED = (1 << 2),
+ PMIC_ARB_STATUS_DROPPED = (1 << 3),
+};
+
+/* Command register fields */
+#define PMIC_ARB_CMD_MAX_BYTE_COUNT 8
+
+/* Command Opcodes */
+enum pmic_arb_cmd_op_code {
+ PMIC_ARB_OP_EXT_WRITEL = 0,
+ PMIC_ARB_OP_EXT_READL = 1,
+ PMIC_ARB_OP_EXT_WRITE = 2,
+ PMIC_ARB_OP_RESET = 3,
+ PMIC_ARB_OP_SLEEP = 4,
+ PMIC_ARB_OP_SHUTDOWN = 5,
+ PMIC_ARB_OP_WAKEUP = 6,
+ PMIC_ARB_OP_AUTHENTICATE = 7,
+ PMIC_ARB_OP_MSTR_READ = 8,
+ PMIC_ARB_OP_MSTR_WRITE = 9,
+ PMIC_ARB_OP_EXT_READ = 13,
+ PMIC_ARB_OP_WRITE = 14,
+ PMIC_ARB_OP_READ = 15,
+ PMIC_ARB_OP_ZERO_WRITE = 16,
+};
+
+/* Maximum number of support PMIC peripherals */
+#define PMIC_ARB_MAX_PERIPHS 256
+#define PMIC_ARB_PERIPH_ID_VALID (1 << 15)
+#define PMIC_ARB_TIMEOUT_US 100
+#define PMIC_ARB_MAX_TRANS_BYTES (8)
+
+#define PMIC_ARB_APID_MASK 0xFF
+#define PMIC_ARB_PPID_MASK 0xFFF
+
+/* interrupt enable bit */
+#define SPMI_PIC_ACC_ENABLE_BIT BIT(0)
+
+/**
+ * spmi_pmic_arb_dev - SPMI PMIC Arbiter object
+ *
+ * @base: address of the PMIC Arbiter core registers
+ * @intr: address of the SPMI interrupt control registers
+ * @cnfg: address of the PMIC Arbiter configuration registers
+ * @mapping_table: in-memory copy of PPID -> APID mapping table
+ */
+struct spmi_pmic_arb_dev {
+ void __iomem *base;
+ void __iomem *intr;
+ void __iomem *cnfg;
+ bool allow_wakeup;
+ spinlock_t lock;
+ u8 channel;
+ u8 min_apid;
+ u8 max_apid;
+ u32 mapping_table[SPMI_MAPPING_TABLE_LEN];
+};
+
+static inline u32 pmic_arb_base_read(struct spmi_pmic_arb_dev *dev, u32 offset)
+{
+ return readl_relaxed(dev->base + offset);
+}
+
+static inline void pmic_arb_base_write(struct spmi_pmic_arb_dev *dev, u32 offset,
+ u32 val)
+{
+ writel_relaxed(val, dev->base + offset);
+}
+
+/**
+ * pa_read_data: reads pmic-arb's register and copy 1..4 bytes to buf
+ * @bc byte count -1. range: 0..3
+ * @reg register's address
+ * @buf output parameter, length must be bc+1
+ */
+static void pa_read_data(struct spmi_pmic_arb_dev *dev, u8 *buf, u32 reg, u8 bc)
+{
+ u32 data = pmic_arb_base_read(dev, reg);
+ memcpy(buf, &data, (bc & 3) + 1);
+}
+
+/**
+ * pa_write_data: write 1..4 bytes from buf to pmic-arb's register
+ * @bc byte-count -1. range: 0..3
+ * @reg register's address
+ * @buf buffer to write. length must be bc+1
+ */
+static void
+pa_write_data(struct spmi_pmic_arb_dev *dev, const u8 *buf, u32 reg, u8 bc)
+{
+ u32 data = 0;
+ memcpy(&data, buf, (bc & 3) + 1);
+ pmic_arb_base_write(dev, reg, data);
+}
+
+static int pmic_arb_wait_for_done(struct spmi_controller *ctrl)
+{
+ struct spmi_pmic_arb_dev *dev = spmi_controller_get_drvdata(ctrl);
+ u32 status = 0;
+ u32 timeout = PMIC_ARB_TIMEOUT_US;
+ u32 offset = PMIC_ARB_STATUS(dev->channel);
+
+ while (timeout--) {
+ status = pmic_arb_base_read(dev, offset);
+
+ if (status & PMIC_ARB_STATUS_DONE) {
+ if (status & PMIC_ARB_STATUS_DENIED) {
+ dev_err(&ctrl->dev,
+ "%s: transaction denied (0x%x)\n",
+ __func__, status);
+ return -EPERM;
+ }
+
+ if (status & PMIC_ARB_STATUS_FAILURE) {
+ dev_err(&ctrl->dev,
+ "%s: transaction failed (0x%x)\n",
+ __func__, status);
+ return -EIO;
+ }
+
+ if (status & PMIC_ARB_STATUS_DROPPED) {
+ dev_err(&ctrl->dev,
+ "%s: transaction dropped (0x%x)\n",
+ __func__, status);
+ return -EIO;
+ }
+
+ return 0;
+ }
+ udelay(1);
+ }
+
+ dev_err(&ctrl->dev,
+ "%s: timeout, status 0x%x\n",
+ __func__, status);
+ return -ETIMEDOUT;
+}
+
+/* Non-data command */
+static int pmic_arb_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid)
+{
+ struct spmi_pmic_arb_dev *pmic_arb = spmi_controller_get_drvdata(ctrl);
+ unsigned long flags;
+ u32 cmd;
+ int rc;
+
+ dev_dbg(&ctrl->dev, "op:0x%x sid:%d\n", opc, sid);
+
+ /* Check for valid non-data command */
+ if (opc < SPMI_CMD_RESET || opc > SPMI_CMD_WAKEUP)
+ return -EINVAL;
+
+ cmd = ((opc | 0x40) << 27) | ((sid & 0xf) << 20);
+
+ spin_lock_irqsave(&pmic_arb->lock, flags);
+ pmic_arb_base_write(pmic_arb, PMIC_ARB_CMD(pmic_arb->channel), cmd);
+ rc = pmic_arb_wait_for_done(ctrl);
+ spin_unlock_irqrestore(&pmic_arb->lock, flags);
+
+ return rc;
+}
+
+static int pmic_arb_read_cmd(struct spmi_controller *ctrl,
+ u8 opc, u8 sid, u16 addr, u8 bc, u8 *buf)
+{
+ struct spmi_pmic_arb_dev *pmic_arb = spmi_controller_get_drvdata(ctrl);
+ unsigned long flags;
+ u32 cmd;
+ int rc;
+
+ if (bc >= PMIC_ARB_MAX_TRANS_BYTES) {
+ dev_err(&ctrl->dev,
+ "pmic-arb supports 1..%d bytes per trans, but:%d requested",
+ PMIC_ARB_MAX_TRANS_BYTES, bc+1);
+ return -EINVAL;
+ }
+ dev_dbg(&ctrl->dev,
+ "op:0x%x sid:%d bc:%d addr:0x%x\n", opc, sid, bc, addr);
+
+ /* Check the opcode */
+ if (opc >= 0x60 && opc <= 0x7F)
+ opc = PMIC_ARB_OP_READ;
+ else if (opc >= 0x20 && opc <= 0x2F)
+ opc = PMIC_ARB_OP_EXT_READ;
+ else if (opc >= 0x38 && opc <= 0x3F)
+ opc = PMIC_ARB_OP_EXT_READL;
+ else
+ return -EINVAL;
+
+ cmd = (opc << 27) | ((sid & 0xf) << 20) | (addr << 4) | (bc & 0x7);
+
+ spin_lock_irqsave(&pmic_arb->lock, flags);
+ pmic_arb_base_write(pmic_arb, PMIC_ARB_CMD(pmic_arb->channel), cmd);
+ rc = pmic_arb_wait_for_done(ctrl);
+ if (rc)
+ goto done;
+
+ /* Read from FIFO, note 'bc' is actually number of bytes minus 1 */
+ pa_read_data(pmic_arb, buf, PMIC_ARB_RDATA0(pmic_arb->channel)
+ , min_t(u8, bc, 3));
+
+ if (bc > 3)
+ pa_read_data(pmic_arb, buf + 4,
+ PMIC_ARB_RDATA1(pmic_arb->channel), bc - 4);
+
+done:
+ spin_unlock_irqrestore(&pmic_arb->lock, flags);
+ return rc;
+}
+
+static int pmic_arb_write_cmd(struct spmi_controller *ctrl,
+ u8 opc, u8 sid, u16 addr, u8 bc, const u8 *buf)
+{
+ struct spmi_pmic_arb_dev *pmic_arb = spmi_controller_get_drvdata(ctrl);
+ unsigned long flags;
+ u32 cmd;
+ int rc;
+
+ if (bc >= PMIC_ARB_MAX_TRANS_BYTES) {
+ dev_err(&ctrl->dev,
+ "pmic-arb supports 1..%d bytes per trans, but:%d requested",
+ PMIC_ARB_MAX_TRANS_BYTES, bc+1);
+ return -EINVAL;
+ }
+ dev_dbg(&ctrl->dev,
+ "op:0x%x sid:%d bc:%d addr:0x%x\n", opc, sid, bc, addr);
+
+ /* Check the opcode */
+ if (opc >= 0x40 && opc <= 0x5F)
+ opc = PMIC_ARB_OP_WRITE;
+ else if (opc >= 0x00 && opc <= 0x0F)
+ opc = PMIC_ARB_OP_EXT_WRITE;
+ else if (opc >= 0x30 && opc <= 0x37)
+ opc = PMIC_ARB_OP_EXT_WRITEL;
+ else if (opc >= 0x80 && opc <= 0xFF)
+ opc = PMIC_ARB_OP_ZERO_WRITE;
+ else
+ return -EINVAL;
+
+ cmd = (opc << 27) | ((sid & 0xf) << 20) | (addr << 4) | (bc & 0x7);
+
+ /* Write data to FIFOs */
+ spin_lock_irqsave(&pmic_arb->lock, flags);
+ pa_write_data(pmic_arb, buf, PMIC_ARB_WDATA0(pmic_arb->channel)
+ , min_t(u8, bc, 3));
+ if (bc > 3)
+ pa_write_data(pmic_arb, buf + 4,
+ PMIC_ARB_WDATA1(pmic_arb->channel), bc - 4);
+
+ /* Start the transaction */
+ pmic_arb_base_write(pmic_arb, PMIC_ARB_CMD(pmic_arb->channel), cmd);
+ rc = pmic_arb_wait_for_done(ctrl);
+ spin_unlock_irqrestore(&pmic_arb->lock, flags);
+
+ return rc;
+}
+
+static int spmi_pmic_arb_probe(struct platform_device *pdev)
+{
+ struct spmi_pmic_arb_dev *pa;
+ struct spmi_controller *ctrl;
+ struct resource *res;
+ int err, i;
+
+ ctrl = spmi_controller_alloc(&pdev->dev, sizeof(*pa));
+ if (!ctrl)
+ return -ENOMEM;
+
+ pa = spmi_controller_get_drvdata(ctrl);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "core");
+ pa->base = devm_ioremap_resource(&ctrl->dev, res);
+ if (IS_ERR(pa->base)) {
+ err = PTR_ERR(pa->base);
+ goto err_put_ctrl;
+ }
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "intr");
+ pa->intr = devm_ioremap_resource(&ctrl->dev, res);
+ if (IS_ERR(pa->intr)) {
+ err = PTR_ERR(pa->intr);
+ goto err_put_ctrl;
+ }
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "cnfg");
+ pa->cnfg = devm_ioremap_resource(&ctrl->dev, res);
+ if (IS_ERR(pa->cnfg)) {
+ err = PTR_ERR(pa->cnfg);
+ goto err_put_ctrl;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(pa->mapping_table); ++i)
+ pa->mapping_table[i] = readl_relaxed(
+ pa->cnfg + SPMI_MAPPING_TABLE_REG(i));
+
+ platform_set_drvdata(pdev, ctrl);
+ spin_lock_init(&pa->lock);
+
+ pa->channel = 0;
+ pa->max_apid = 0;
+ pa->min_apid = PMIC_ARB_MAX_PERIPHS - 1;
+
+ ctrl->cmd = pmic_arb_cmd;
+ ctrl->read_cmd = pmic_arb_read_cmd;
+ ctrl->write_cmd = pmic_arb_write_cmd;
+
+ err = spmi_controller_add(ctrl);
+ if (err)
+ goto err_put_ctrl;
+
+ dev_dbg(&ctrl->dev, "PMIC Arb Version 0x%x\n",
+ pmic_arb_base_read(pa, PMIC_ARB_VERSION));
+
+ return 0;
+
+err_put_ctrl:
+ spmi_controller_put(ctrl);
+ return err;
+}
+
+static int __exit spmi_pmic_arb_remove(struct platform_device *pdev)
+{
+ struct spmi_controller *ctrl = platform_get_drvdata(pdev);
+ spmi_controller_remove(ctrl);
+ return 0;
+}
+
+static struct of_device_id spmi_pmic_arb_match_table[] = {
+ { .compatible = "qcom,spmi-pmic-arb", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, spmi_pmic_arb_match_table);
+
+static struct platform_driver spmi_pmic_arb_driver = {
+ .probe = spmi_pmic_arb_probe,
+ .remove = __exit_p(spmi_pmic_arb_remove),
+ .driver = {
+ .name = "spmi_pmic_arb",
+ .owner = THIS_MODULE,
+ .of_match_table = spmi_pmic_arb_match_table,
+ },
+};
+module_platform_driver(spmi_pmic_arb_driver);